Check The Signal Status; Set The Hdcp Settings; Emulate The Correct Edid - Lightware UBEX-PRO20-HDMI-F110 User Manual

 
     
3. Installation 3. Installation
3.6.4. Check the Signal Status
The Crosspoint menu in the LDC software displays all important information about the incoming, transmitting,
and outgoing HDMI signals. For more detailed information see the
The video crosspoint menu in the LDC software for TX-RX pair
Transmitter (UBEX TX) Side
Step 1. Check the HDMI signal status on the HDMI in 1 and 2 input ports - if the signal status indicator is green, the
signal is present; if it is grey, there is no incoming signal on the port.
Step 2. Check the HDMI signal status on the HDMI out 1 and 2 local output ports - if the signal status indicator is
green, the signal is present and sink device is connected; if it is grey, no transmitted signal on the port.
Step 3. Check the video streams in the Stream 1 and 2 panels - if the signal status indicator is green, the signal is
present; if it is grey, there is no incoming signal on the port. Also check the enable status of the stream
on the stream settings panel.
Receiver (UBEX RX) Side
Step 1. Check the Stream switcher - the desired stream is switched to the HDMI output port.
Step 2. Check the HDMI signal status on the HDMI out 1 and 2 output ports - if the signal status indicator is green,
the signal is present and sink device is connected; if it is grey, no transmitted signal on the port.
Transceiver (UBEX TRX) Side
Step 1. Check the HDMI signal status on the HDMI in 2 input port - if the signal status indicator is green, the signal
is present; if it is grey, there is no incoming signal on the port.
Step 2. Check the HDMI signal status on the HDMI out 1 output port - if the signal status indicator is green, the
signal is present and sink device is connected; if it is grey, no transmitted signal on the port.
UBEX series – Extender Application Mode – User's Manual UBEX series – Extender Application Mode – User's Manual
Video Crosspoint Menu section.
Applied F-series endpoint firmware package: v1.4.1 | Applied R-series endpoint firmware package: v1.4.1 | LDC software: v1.34.0b2
SFP+ Links
Check the connection status of the SFP+ links:
▪ Green arrows mean connection is established and TCP/IP packages are
transmitted successfully.
▪ Amber arrows mean connection is established but error happened during
the transmission of the TCP/IP packages - check the SFP+ connection.
▪ Red arrows mean no connection is established between the endpoint
devices.
3.6.5. Set the HDCP Settings
Check the HDCP settings either on the input and output ports. For more details about the HDCP technology
see the HDCP Management section.
▪ Open the HDMI in 1 and 2 port properties
panel on the transmitter or transceiver side
and check the HDCP enable setting. Put a tick
to enable HDCP capability on the port.
▪ Open the HDMI out 1 and 2 local output
port properties panels on the transmitter or
transceiver side and check the HDCP mode
setting.
▪ Open the HDMI out 1 and 2 output port
properties panels on the receiver
transceiver side and check the HDCP mode
setting.
INFO:
UBEX extenders always authenticate the highest version of HDCP-encryption and cannot force the
lower version.
3.6.6. Emulate the Correct EDID
Emulate the right EDID to the HDMI input ports of the transmitter/transceiver. The EDID must be set according
to the desired resolution / refresh rate of the stream.
INFO:
You can find detailed information about the EDID Management menu of the LDC software in the
EDID Management Menu section; about the technology in general please read the
section.
Navigate to the EDID Management menu in the LDC software. Select the Emulated EDIDs on the right side panel,
and select Factory EDIDs on the left side panel. See the entire list of the pre-installed factory EDIDs in the
Factory EDID List section.
or
EDID Management
32 32