Local Trx O1 Port; Remote Trx I2 Port; Remote Trx O1 Port - Lightware UBEX-PRO20-HDMI-F110 User Manual

 
     
5. Front Panel LCD Menu Operations 5. Front Panel LCD Menu Operations
Video Settings
The following settings can be set for the stream of the HDMI input 2
port:
▪ Resolution mode #frc
– Passthrough: pass-through mode; the original resolution of
the stream is transmitted.
– Forced: the resolution which is set in the Resolution setting
menu is forced.
▪ Resolution setting - select a resolution to force from the pre-
installed list. The entire list can be found in the
the Scaler / FRC section.
▪ Image Position - Center
▪ Color space - Passthrough / Force RGB / Force YCbCr 4:4:4 /
Force YCbCr 4:2:2 #csc #colorspace
Stream Output
The following settings and information is related to the video stream
which is sent toward the remote TRX endpoint:
▪ Stream enable - Enabled / Disabled
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
5.5.2. Local TRX O1 Port
Stream Input
The following settings and information are related to the video stream
coming from the input port of the remote TRX endpoint:
▪ Stream enable - Enabled / Disabled
Signal present
▪
▪ Active resolution
▪ Total resolution
▪ Color space
Video Settings
The following settings can be set for the stream of the HDMI output 1
port:
▪
Resolutions of
▪
▪
▪
▪
#streamenable
#streamenable
HDMI Output
The following information are displayed for the HDMI output 2 port of
the transceiver:
▪
▪
▪
▪
▪
▪
▪
Applied F-series endpoint firmware package: v1.4.1 | Applied R-series endpoint firmware package: v1.4.1 | LDC software: v1.34.0b2
UBEX series – Extender Application Mode – User's Manual UBEX series – Extender Application Mode – User's Manual
Resolution mode #scaler
– Passthrough: pass-through mode; the original resolution of
the stream is transmitted.
– Forced: the resolution which is set in the Resolution setting
menu is forced.
– EdidBased: the resolution which is read out from the EDID of
the connected sink device is forced.
Resolution setting - select a resolution to force from the pre-
installed list. The entire list can be found in the Resolutions of
the Scaler / FRC section.
Image position - Center / Fit / Stretch
Color space - Passthrough / Force RGB / Force YCbCr 4:4:4 /
Force YCbCr 4:2:2 #csc #colorspace
No sync mode - the No sync mode feature generates an image
which can be displayed when there is no incoming signal on
the port. The following settings can be set for the Test Pattern
function: #testpattern #nosyncscreen
– Always off - the test pattern function is disabled, the video
output port transmits the video signal of the selected input
port.
– No signal mode - the video output port transmits the test
pattern if there is no incoming signal on the selected input
port.
– Always on - the video output port always transmits the test
pattern.
#hdcp #power5v
HDCP mode - Auto / Always
Output 5V mode - Always on / Auto / Always off
Hotplug detect
Signal present
Active resolution
Total resolution
Color space
5.5.3. Remote TRX I2 Port
The following information is related for the HDMI input port of the
connected remote transceiver.
HDMI Input
▪ +5V present
▪ Signal present
▪ Active resolution
Total resolution
▪
▪ Color space
Stream Output
▪ Signal present
▪ Active resolution
▪ Total resolution
Color space
▪
5.5.4. Remote TRX O1 Port
The following information is related for the HDMI output port of the
connected remote transceiver.
Stream Input
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
HDMI Output
Hotplug detect
▪
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
52 52