Rx Hdmi Output 1 And 2 Ports; Overview; Ports Menu - Transceiver Mode; Local Trx I2 Port - Lightware UBEX-PRO20-HDMI-F110 User Manual

 
     
5. Front Panel LCD Menu Operations 5. Front Panel LCD Menu Operations
5.4.1. RX HDMI Output 1 and 2 Ports
Stream Input
The following settings and information are related to the video stream
coming from the TX input ports:
▪ Stream enable - Enabled / Disabled
▪ Signal present
▪ Active resolution
Total resolution
▪
▪ Color space
Video Settings
The following settings can be set in the case of both output ports:
▪ #scaler #frc
Resolution mode
– Passthrough: pass-through mode; the original resolution of
the stream is transmitted.
– Forced: the resolution which is set in the Resolution setting
menu is forced.
– EdidBased: the resolution which is read out from the EDID of
the connected sink device is forced.
▪ Resolution setting - select a resolution to force from the pre-
installed list. The entire list can be found in the
the Scaler / FRC section.
▪ Image position - Center / Fit / Stretch
INFO:
The Image position setting on the HDMI OUT 2 port is a read-
only parameter and fixed as "Center".
▪ Color space - Passthrough / Force RGB / Force YCbCr 4:4:4 /
Force YCbCr 4:2:2 #csc #colorspace
▪ No Sync mode - the No sync mode feature generates an image
which can be displayed when there is no incoming signal on
the port. The following settings can be set for the Test Pattern
function: #testpattern #nosyncscreen
– Always off - the test pattern function is disabled, the video output
port transmits the video signal of the selected input port.
– No signal mode - the video output port transmits the test
pattern if there is no incoming signal on the selected input
port.
– Always on - the video output port always transmits the test
pattern.
HDMI Output
The following information are displayed in the case of both output
ports of the receiver:
▪
▪
#streamenable
▪
▪
▪
▪
▪
5.4.2. Overview
The current status of the output ports is
summarized in the Overview menu. The
icons display information about the port and
the transmitted signals.
TIPS AND TRICKS:

selected port for the settings and detailed
status information.
Icon
Resolutions of 



Applied F-series endpoint firmware package: v1.4.1 | Applied R-series endpoint firmware package: v1.4.1 | LDC software: v1.34.0b2
UBEX series – Extender Application Mode – User's Manual UBEX series – Extender Application Mode – User's Manual
#hdcp #power5v
HDCP mode - Auto / Always
Output 5V mode - Always on / Auto / Always off
Hotplug detect
Signal present
Active resolution
Total resolution
Color space
Press enter on the
Icon is blue (inactive) Icon is white (active)
Sink is not connected Sink is connected
Signal is not present Signal is present
Signal is not encrypted with Signal is encrypted with
HDCP HDCP
No audio signal in the video Audio is embedded in the
stream video stream
5.5. Ports Menu - Transceiver Mode
The most important settings and status
information of the HDMI input 1 and the
HDMI output ports are available in the Ports
menu.
Select the desired output port and enter to
see the submenus.
The following port diagrams help to identify
and navigate to the desired submenu:
Port diagram - Transceiver mode
5.5.1. Local TRX I2 Port
HDMI Input
The HDCP setting and information about the HDMI input 1 port are
displayed:
▪ HDCP enable - Enabled / Disabled #hdcp
▪ +5V present
▪ Signal present
▪ Active resolution
▪ Total resolution
▪ Color space
51 51