Mitsubishi Electric MDS-E Series Instruction Manual page 510

MDS-E/EH Series Instruction Manual
11 Appx. 2: D/A Output Specifications for Drive Unit
< Spindle control signal >
Spindle control input (NC to Spindle)
No.
16384 Spindle control input 1-0
16385 Spindle control input 1-1
16391 Spindle control input 1-7
16392 Spindle control input 1-8
16393 Spindle control input 1-9
16394 Spindle control input 1-A
16409 Spindle control input 2-9
16410 Spindle control input 2-A
16411 Spindle control input 2-B
16432 Spindle control input 4-0
16433 Spindle control input 4-1
16434 Spindle control input 4-2
16436 Spindle control input 4-4
16437 Spindle control input 4-5
16438 Spindle control input 4-6
16445 Spindle control input 4-D
16458 Spindle control input 5-A
16459 Spindle control input 5-B
16460 Spindle control input 5-C
16461 Spindle control input 5-D
16462 Spindle control input 5-E
16472 Spindle control input 6-8
(Note 1) Control signal is bit output. Setting the No. of the table above to the data output (SP125, SP126), and when
the scale (SP127, SP128) is set to "0", the output is "0V" for bit 0, and "2.5V" for bit 1.
(Note 2) Refer to "Spindle control signal" for details on the spindle control signal.
Details
READY ON command
Servo ON command
Alarm reset command
Torque limit 1 selection
command
Torque limit 2 selection
command
Torque limit 3 selection
command
Speed monitor command
valid
In door closed (controller)
In door closed (all drive units)
Spindle control mode
selection command 1
Spindle control mode
selection command 2
Spindle control mode
selection command 3
Gear changeover command
Gear selection command 1
Gear selection command 2
L coil selection command
Phase synchronization
suppression command
Minimum excitation rate 2
changeover request
Speed gain set 2 changeover
request
Zero point re-detection
request
Increase holding power of
spindle
Drivers communication
control request
479
Spindle control output (Spindle to NC)
No.
16480 Spindle control output 1-0
16481 Spindle control output 1-1
16487 Spindle control output 1-7
16488 Spindle control output 1-8
16489 Spindle control output 1-9
16490 Spindle control output 1-A
16492 Spindle control output 1-C
16495 Spindle control output 1-F
16496 Spindle control output 2-0
16499 Spindle control output 2-3
16503 Spindle control output 2-7
16505 Spindle control output 2-9
16506 Spindle control output 2-A
16507 Spindle control output 2-B
16528 Spindle control output 4-0
16529 Spindle control output 4-1
16530 Spindle control output 4-2
16532 Spindle control output 4-4
16533 Spindle control output 4-5
16534 Spindle control output 4-6
16535 Spindle control output 4-7
16541 Spindle control output 4-D
16545 Spindle control output 5-1
16550 Spindle control output 5-6
16554 Spindle control output 5-A
16555 Spindle control output 5-B
16556 Spindle control output 5-C
16557 Spindle control output 5-D
16558 Spindle control output 5-E
16559 Spindle control output 5-F
16568 Spindle control output 6-8
Details
In ready ON
In servo ON
In alarm
In torque limit 1 selection
In torque limit 2 selection
In torque limit 3 selection
In in-position
In warning
Z phase passed
In zero speed
In external emergency stop
In speed monitor
In door closed (controller)
In door closed (self drive unit)
In spindle control mode
selection 1
In spindle control mode
selection 2
In spindle control mode
selection 3
In gear changeover
command
In gear selection 1
In gear selection 2
Magnetic pole position not
set
In L coil selection
Speed detection
In coil changeover
In phase synchronization
suppression
In minimum excitation rate 2
selection
In speed gain set 2 selection
Zero point re-detection
complete
Increase holding power of
spindle completed
In 2nd in-position
In drivers communication
control
IB-1501229-F