Mitsubishi Electric MDS-E Series Instruction Manual page 24

6.1.7 Spindle C Axis Adjustment (For Lathe System) ...................................................................................... 347
6.1.8 Spindle Synchronization Adjustment (For Lathe System) ..................................................................... 352
6.1.9 Deceleration Coil Changeover Valid Function by Emergency Stop ...................................................... 354
6.1.10 High-response Acceleration/Deceleration Function ............................................................................. 355
6.1.11 Spindle Cutting Withstand Level Improvement..................................................................................... 356
6.1.12 Spindle Motor Temperature Compensation Function........................................................................... 357
6.2 Settings for Emergency Stop............................................................................................................................. 362
6.2.1 Deceleration Control .................................................................................................................................. 362
6.3 Spindle Control Signal........................................................................................................................................ 363
6.3.1 Spindle Control Input (NC to Spindle) ...................................................................................................... 363
6.3.2 Spindle Control Output (Spindle to NC) ................................................................................................... 368
7 Troubleshooting....................................................................................................................................... 373
7.1 Points of Caution and Confirmation.................................................................................................................. 374
7.1.1 LED Display When Alarm or Warning Occurs ......................................................................................... 375
7.2 Protective Functions List of Units..................................................................................................................... 376
7.2.1 List of Alarms ............................................................................................................................................. 376
7.2.2 List of Warnings ......................................................................................................................................... 385
7.3 Troubleshooting.................................................................................................................................................. 387
7.3.1 Troubleshooting at Power ON................................................................................................................... 387
7.3.2 Troubleshooting for Each Alarm No......................................................................................................... 388
7.3.3 Troubleshooting for Each Warning No..................................................................................................... 414
7.3.4 Parameter Numbers during Initial Parameter Error ................................................................................ 417
7.3.5 Troubleshooting the Spindle System When There Is No Alarm or Warning ........................................ 420
7.3.6 Details of Alarm 4D .................................................................................................................................... 422
8 Maintenance ............................................................................................................................................. 425
8.1 Periodic Inspections ........................................................................................................................................... 426
8.1.1 Inspections ................................................................................................................................................. 426
8.1.2 Cleaning of Spindle Motor ......................................................................................................................... 426
8.2 Service Parts ....................................................................................................................................................... 438
8.3 Adding and Replacing Units and Parts............................................................................................................. 439
8.3.1 Replacing the Drive Unit ............................................................................................................................ 439
8.3.2 Replacing the Unit Fan .............................................................................................................................. 440
8.3.3 Replacing the Battery ................................................................................................................................ 442
9 Power Backup System............................................................................................................................. 445
9.1 Deceleration and Stop Function at Power Failure ........................................................................................... 446
9.1.1 Specifications of Stop Method for Deceleration and Stop Function at Power Failure System .......... 446
9.1.2 Wiring of Deceleration and Stop Function at Power Failure .................................................................. 447
9.1.3 Setup of Deceleration and Stop Function at Power Failure ................................................................... 448
9.2 Retraction function at power failure.................................................................................................................. 450
9.2.1 Wiring of Retraction Function at Power Failure ...................................................................................... 450
9.2.2 Setup of Retraction Function at Power Failure System.......................................................................... 453
9.3 Explanation of Each Part of Power Backup System........................................................................................ 455
9.3.1 How to Set Rotary Switch and Dip Switches ........................................................................................... 455
9.3.2 Transition of LED Display After Power Is Turned ON ............................................................................. 455
9.4 Troubleshooting for Power Backup System .................................................................................................... 456
9.4.1 LED Display When Alarm or Warning Occurs ......................................................................................... 456
9.4.2 List of Power Backup Function Alarms.................................................................................................... 457
9.4.3 List of Power Backup Function Warnings ............................................................................................... 457
9.4.4 Troubleshooting for Each Alarm No......................................................................................................... 458
9.4.5 Troubleshooting for Each Warning No..................................................................................................... 461
9.4.6 Trouble Shooting at Power ON ................................................................................................................. 462
10 Appx. 1: Cable and Connector Assembly............................................................................................ 463
10.1 CMV1-xPxxS-xx Plug Connector ..................................................................................................................... 464
10.2 1747464-1 Plug Connector ............................................................................................................................... 470
10.2.1 Applicable Products................................................................................................................................. 470
10.2.2 Applicable Cable ...................................................................................................................................... 470
10.2.3 Related Documents .................................................................................................................................. 470
10.2.4 Assembly Procedure................................................................................................................................ 470
11 Appx. 2: D/A Output Specifications for Drive Unit.............................................................................. 473
11.1 D/A Output Specifications................................................................................................................................ 474
11.2 Output Data Settings ........................................................................................................................................ 475
11.2.1 Servo Drive Unit Settings ........................................................................................................................ 475
11.2.2 Spindle Drive Unit Settings ..................................................................................................................... 477