Menu H: Configuration - Emerson E300 Series Design Manual

Safety Product Mechanical
information information installation
8.7

Menu H: Configuration

Parameter
H01 User Security Code
H02 User Security Status
H03 Security Status
H04 Default Drive
Output Phase Loss Detection
H06
Enable
Output Phase Loss Detection
H07
Time
Input Phase Loss Detection
H08
Mode Enable
H09 Direct To Floor Sensor Mode
H10 Direct To Floor Edge Detection
H11 Control Input mode
H12 Direction Input Invert
H13 Velocity Threshold 1
H14 Velocity Threshold 2
Maximum Speed Error
H15
Threshold
Maximum Distance Error
H16
Threshold
H17 Current Controller Mode
H18 Fan Maximum Speed
H19 Elevator Control Mode
H20 Fast Start Enable
H21 Fast Start Monitoring Distance
H22 Short Floor Landing Enable
H23 Floor Sensor Correction Enable
Floor Sensor Correction Source
H24
Select
Floor Sensor Correction Edge
H25
Detection
H26 Fast Stop Enable
H27 Rapid Slow Down Enable
H28 Freeze Protection Threshold
H29 Normal Duty Enable
H30 Position Display Mode
H31 Elevator Trip Disable
H32 Date/Time Selector
H33 Date Format
H34 Turn On delay
H35 Standby Mode Enable
H36 Standby Mode Mask
H37 Reset Energy Meter
Blocked Elevator Release
H38
Enable Input
Parameter Displayed At
H39
Power-up
H40 Drive Name Characters 1-4
H41 Drive Name Characters 5-8
H42 Drive Name Characters 9-12
H43 Drive Name Characters 13-16
H45 Action On Trip Detection
H46 Number Of Auto reset Attempts
H47 Auto-reset Delay
304
Electrical Getting
User Menu A Commissioning
installation started
Range( )
Open-Loop RFC-A
0 to 2147483647
Menu 0 (0), All Menus (1), Read-only Menu 0 (2),
Read-only (3), Status Only (4), No Access (5)
None (0), Read-only (1), Status-only (2), No Access (3)
None (0), Standard (1), US (2)
Disabled (0), Enabled (1)
0.5s (0), 1.0s (1), 2.0s (2), 4.0s (3)
Full (0), Ripple Only (1), Disabled (2)
Spd IP (0), Stop IP (1),
Spd IP+User Dist (2)
Rising 1st (0), Falling 1st (1)
Analog Run Prmit (0),
Analog 2 Dir (1), Priority 1 Dir (2),
Binary 1 Dir (3), Priority 2 Dir (4),
Binary 2 Dir (5), Control Word (6)
Off (0) or On (1)
0 to 10000 mm/s
0 to 10000 mm/s
0 to 10000 mm/s
0 to 10000 mm
Off (0) or On (1)
±10
Creep To Floor (0),
Direct To Floor (1)
Off (0) or On (1)
0 to 10000 mm
Off (0) or On (1)
Off (0) or On (1)
Floor Sensor IP (0),
Creep Spd IP (1)
Rising 1st (0), Falling 1st (1)
Off (0) or On (1)
Off (0) or On (1)
-10 to 0 °C
Off (0) or On (1)
Relative (0), Absolute (1)
Trips Enabled (0), Trips Disabled (1)
Set (0), Powered (1), Running (2), Acc Powered (3),
Local Keypad (4), Remote Keypad (5), Slot 1 (6),
Slot 2 (7), Slot 3 (8), Slot 4 (9)
Std (0), US (1)
200 to 65535 ms
Off (0) or On (1)
0000000 to 1111111
Off (0) or On (1)
Off (0) or On (1)
A00 to A80
-2147483648 to 2147483647
-2147483648 to 2147483647
-2147483648 to 2147483647
-2147483648 to 2147483647
00000 to 11111
None (0), 1 (1), 2 (2), 3 (3), 4 (4), 5 (5), Infinite (6)
1.0 to 600.0 s
Advanced
Diagnostics Optimization CT MODBUS RTU Technical Data
Parameters
Default( )
Open-Loo
RFC-S RFC-A
p
None (0)
Enabled (1)
0.5s (0)
Full (0)
Spd IP (0)
Rising 1st (0)
Priority 1 Dir (2)
Off (0)
300 mm/s
300 mm/s
100 mm/s
100 mm
10
Creep To Floor (0)
200 mm
Floor Sensor IP (0)
Rising 1st (0)
Off (0)
Off (0)
0 °C
Off (0)
Relative (0)
Trips Enabled (0)
Powered (1)
Std (0)
200 ms
Off (0)
0000000
Off (0)
A06
0
0
0
0
00000
None (0)
1.0 s
Type
RFC-S
RW Num ND NC PT US
RW Txt ND
RO Txt ND NC PT PS
RW Txt NC
RW Txt
RW Txt
RW Txt
RW Txt
RW Txt
RW Txt
RW Bit
RW Num
RW Num
RW Num
RW Num
Off (0) RW Bit
RW Num
RW Txt
Off (0) RW Bit
RW Num
Off (0) RW Bit
Off (0) RW Bit
RW Txt
RW Txt
RW Bit
RW Bit
RW Num
RW Bit
RW Txt
RW Txt
RW Txt
RW Txt
RW Num
RW Bit
RW Bin
RW Bit
Off (0) RW Bit
RW Num
RW Num
RW Num
RW Num
RW Num
RW Bin
RW Txt
RW Num
E300 Design Guide
Issue Number: 1
PT
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
US
PT US
PT US
PT US
PT US
PT US
US
US
US