Table of Contents
Advertisement
Safety
Product
Mechanical
information
information
installation
5.16.1
NV Media Card trips
The NV Media Card should not be removed during data transfer as the drive will produce a trip. If this occurs, then either the transfer should be re-
attempted or in the case of a NV Media Card to drive transfer, default parameters should be loaded.
After an attempt to read, write or erase data from a NV Media Card a trip is initiated if there has been a problem with the command. See the
diagnostics section for more information on the NV Media Card trips.
5.16.2
Data block header information
Each data block stored on a NV Media Card has header information as detailed in the following parameters:
•
Media card file number (N03)
•
Media card file type (N04)
•
Media card file version (N05)
•
Media card file checksum (N06)
The header information for each data block used can be viewed in Media card file type (N04) to Media card file checksum (N06) by increasing or
decreasing the data block number set in Media card file number (N03). If there is no data on the card Media card file number (N03) can only have a
value of 0.
5.17
NV Media Card transferring data
Data transfer, erasing and protecting the information is performed by entering a code in Pr mm00 and then resetting the drive as shown in Table 5-
11 SMARTCARD and SD card codes .
The whole card may be protected from writing or erasing by setting the read-only flag as detailed in Table 5-11 SMARTCARD and SD card codes .
5.17.1
Reading from the NV Media Card
•
6yyy - Reading from the NV Media Card
When data is transferred to the drive, using 6yyy in Pr mm00, it is transferred to the drive RAM and the EEPROM. A parameter save is not required
to retain the data after power down. If the option modules installed are different between source and destination drives, the menus for the option
module slots where the option module categories are different are not updated from the NV Media Card and will contain their default values. The drive
will produce a 'Card Option' trip if the option module installed to the source and the destination drives are different or are in different slots.
If the data is being transferred to the drive with different voltage or current rating a 'Card Rating' trip will occur. The following drive rating dependant
parameters RA coding bit set) will not be transferred to the destination drive from a NV Media Card when the voltage rating of the destination drive is
different from the source drive and the file is a parameter file. However, drive rating dependent parameters will be transferred if only the current rating
is different. If drive rating dependant parameters are not transferred to the destination drive they will contain their default values.
Parameter number
B15
B02
B03
B04
B35
B13
B34
B36
D18
O18
O11
O14
•
Parameter Cloning (N01) = Read (1) - Reading from the NV Media Card
Setting Parameter Cloning (N01) modes to Read (1) and resetting the drive will transfer parameters from the NV Media Card to the drive parameters
and the drive EEPROM, i.e. this is equivalent to writing 6001 to Pr mm00. Once the parameters are successfully copied this parameter is
automatically reset to None (0). Parameters are saved to the drive EEPROM after this action is complete.
5.17.2
Auto saving drive parameter changes
•
Parameter Cloning (N01) = Auto (3)
This setting causes the drive to automatically save any changes made to User Menu A parameters in the drive to the NV Media Card. If the NV Media
Card data block already contains information it is automatically overwritten.
Changing Parameter Cloning (N01) to Auto (3) and resetting the drive will immediately save the complete parameter set from the drive to the NV
Media Card. Once the whole parameter set is stored only the individual modified User Menu A parameter setting is updated. At power up, if
Parameter Cloning (N01) is set to Auto (3), the drive will save the complete parameter set to the NV Media Card.
Advanced parameter changes are only saved to the NV Media Card when Pr mm00 is set to 'Save Parameters' or 1000 and the drive reset.
If the NV Media Card is removed when Parameter Cloning (N01) is set to 3 Parameter Cloning (N01) is then automatically set to None (0).
When a new NV Media Card is installed Parameter Cloning (N01) must be set back to Auto (3) by the user and the drive reset so the complete
parameter set is rewritten to the new NV Media Card if auto mode is still required.
When Parameter Cloning (N01) is set to Auto (3) the setting of Parameter Cloning (N01) itself is saved to the drive EEPROM but not the NV Media
Card.
E300 Design Guide
Issue Number: 1
Electrical
Getting
User Menu A Commissioning
installation
started
Description
Symmetrical Current Limit
Rated Current
Rated Voltage
Rated Power Factor
Stator Resistance
Maximum Switching Frequency
Transient Inductance
Stator Inductance
Injection Braking Level
Supply Loss Detection Level
Standard Under Voltage Threshold
Low Under Voltage Threshold
Advanced
Diagnostics Optimization CT MODBUS RTU Technical Data
Parameters
117
Advertisement
Table of Contents
