Pos : 2 /D okumentati on allgemein/Ei nband/Ei nband H andbuch - Fronts eite 2015 - mit Doc Variabl en (Standar d) @ 9\mod_1285229289866_0.doc x @ 64941 @ @ 1
Manual
852-1305
8/4-Port 100BASE-T/1000BASE-SX/LX
Industrial-Managed-Switch, 8 Ports 100BASE-T,4
Slots 1000BASE-SX/LX
1.1.0
Pos : 3 /Alle Serien (Allgemeine M odul e)/Rec htlic hes, Allgemei nes/Impressum für Standardhandbüc her - allg. Angaben, Ansc hriften, T elefonnummer n und E-Mail-Adres sen @ 3\mod_1219151118203_21.doc x @ 21060 @ @ 1
WAGO-ETHERNET-Zubehör 852 List of Figures 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 5 /D okumentati on allgemein/Verzeic hnisse/Inhalts verz eichnis - Ü berschrift oG und Verzei chnis @ 3\mod_1219151230875_21.doc x @ 21063 @ @ 1 Table of Contents Notes about this Documentation ............... 10 Validity of this Documentation ...............
Page 4
List of Figures WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Installation Site ..................38 Installation on a Carrier Rail ..............38 Removal from Carrier ail ................ 38 Connect Devices ..................39 Power Supply ..................39 External Alarm Contact Port ..............40 Console Port Cable Connection .............. 40 1000Base-SX/LX Port, Fiber Optic ............
Page 5
WAGO-ETHERNET-Zubehör 852 List of Figures 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.3.1.1 DHCP Snooping ................96 7.3.1.1.1 Server Screening ............... 98 7.3.1.2 Binding Table ................98 7.3.1.3 ARP Inspection ................99 7.3.1.3.1 Filter Table ................100 7.3.2 Access Control List (ACL) ............... 101 7.3.3...
Page 6
List of Figures WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.1.2 Rate Limitation ................142 9.3.1.2.1 Storm Control ................142 9.3.1.2.2 Bandwidth Limitation ............. 144 9.3.2 IGMP Snooping ................145 9.3.2.1 IGMP Snooping ................145 9.3.2.1.1 General Settings ..............145 9.3.2.1.2 Port Settings ................147 9.3.2.1.3...
Page 7
WAGO-ETHERNET-Zubehör 852 List of Figures 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.14 STP ....................199 9.3.14.1 General Settings ................199 9.3.14.2 Port Parameters ................201 9.3.14.3 STP Status ..................204 9.3.15 Xpress Ring ..................206 Security ....................208 9.4.1 IP Source Guard ................208 9.4.1.1...
Page 8
List of Figures WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.1.1 System Information ..............260 10.3.2 Default Settings ................261 10.3.2.1 System ..................261 10.3.2.2 Jumbo Frame ................261 10.3.2.3 SNTP .................... 262 10.3.2.4 Management Host ................ 263 10.3.2.5 MAC Management ..............263 10.3.2.6...
Page 9
WAGO-ETHERNET-Zubehör 852 List of Figures 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.6.3 Mail Alarm ................... 291 10.3.6.4 Maintenance ................. 292 10.3.6.5 System Log .................. 293 10.3.6.6 User Account ................293 10.4 MODBUS/TCP Tables ................294 10.4.1 Data Format and Function Code............294 10.4.2 MODBUS Registers .................
Reproduction, translation, electronic and phototechnical filing/archiving (e.g., photocopying) as well as any amendments require the written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany. Non-observance will involve the right to assert damage claims. Pos : 11.3 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1 Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Notes about this Documentation 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 11.4 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2/Symbol e - Ü berschrift 2 @ 13\mod_1351068042408_21.doc x @ 105270 @ 2 @ 1 Symbols Pos : 11.5.1 /All e Serien ( Allgemei ne Module)/Sicherheits- und sons tige Hi nweis e/Gefahr/Gefahr: _War nung vor Pers onenschäden allgemei n_ - Erläuter ung @ 13\mod_1343309450020_21.doc x @ 101029 @ @ 1...
Page 12
Notes about this Documentation WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Additional Information: Refers to additional information which is not an integral part of this documentation (e.g., the Internet). Pos : 11.6 /Dokumentation allgemei n/Glieder ungs elemente/---Seitenwechs el--- @ 3\mod_1221108045078_0.doc x @ 21810 @ @ 1 Manual 1.1.0...
Notes about this Documentation 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 11.7 /All e Seri en ( Allgemei ne Module)/Ü bers chriften/Ebene 2/D arstellung der Z ahlens ys teme - Ü bers chrift 2 @ 23\mod_1435647128078_21.doc x @ 184811 @ 2 @ 1 Number Notation Pos : 11.8 /All e Seri en ( Allgemei ne Module)/R ec htliches , Allgemei nes /Zahlens ysteme @ 3\mod_1221059454015_21.doc x @ 21711 @ @ 1...
2.1.1 Subject to Changes WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any alterations or modifications that serve to increase the efficiency of technical progress. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from the granting of patents or from the legal protection of utility patents.
Pos : 14.12.2 /Serie 852 ( ETHERN ET-Z ubehör)/Wic htige Erläuterungen/Sicherheits- und sonstig e Hinweis e/Gefahr: Einbau 0852- xxxx nur in Gehäus en, Schr änken oder elektrischen Betri ebsr äumen! @ 22\mod_1432282091645_21.doc x @ 182573 @ @ 1 Only install in appropriate housings, cabinets or electrical operation rooms! WAGO's 852 Series ETHERNET Switches are considered exposed operating components. Therefore, only install these switches in lockable housings, cabinets or electrical operation rooms.
Page 17
WAGO-ETHERNET-Zubehör 852 Important Notes 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Clean only with permitted materials! Clean soiled contacts using oil-free compressed air or with ethyl alcohol and leather cloths. Pos : 14.13.5 /Alle Serien (Allgemeine M odul e)/Sic herheits- und s onstige Hinweise/Achtung/Ac htung: Kei n Kontakts pray verwenden! @ 6\mod_1260181290808_21.doc x @ 46755 @ @ 1 Do not use any contact spray! Do not use any contact spray.
• Do not connect control components and control networks to an open network such as the Internet or an office network. WAGO recommends putting control components and control networks behind a firewall. • Limit physical and electronic access to all automation components to authorized personnel only.
Pos : 16.3 /Serie 852 (ETH ERNET-Zubehör)/Einl eitung/Industriell e ETHERN ET-Technol ogie 852- 1305 @ 27\mod_1466492945844_21.doc x @ 214091 @ 2 @ 1 Industrial ETHERNET Technology The range of WAGO switches ensures scalability of your network infrastructure with outstanding electrical and mechanical characteristics. These robust devices are designed for industrial use and they are fully compliant with IEEE 802.3,...
General WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 16.5 /Serie 852 (ETH ERNET-Zubehör)/Einl eitung/Switc hing-T echnologie @ 3\mod_1222683606296_21.doc x @ 22317 @ 2 @ 1 Switching Technology Another approach to pushing beyond the limits of ETHERNET technology is the development of switching technology. A switch bridge ETHERNET packets at the MAC address level of the ETHERNET protocol transmitting among connected ETHERNET or Fast ETHERNET LAN segments.
Page 21
WAGO-ETHERNET-Zubehör 852 General 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 16.8 /Serie 852 (ETH ERNET-Zubehör)/Gerätebes chr eibung/Einl eitung/Eigenschaften 852- 1305 @ 27\mod_1467270906712_21.doc x @ 215495 @ @ 1 Other key features are: • Eight (8) 10/100/1000BASE-T, four (4) 1000BASE-SX/LX (SFP type fiber transceivers) and one (1) Console port (RJ-45) •...
Pos : 18 /All e Seri en (Allgemei ne Module)/Ü berschriften/Ebene 1/Gerätebes chr eibung - Ü berschrift 1 @ 3\mod_1233756084656_21.doc x @ 27096 @ 1 @ 1 Device Description Pos : 19.1 /Serie 852 (ETH ERNET-Zubehör)/Gerätebes chr eibung/Einl eitung/Ger ätebesc hrei bung 852-1305 @ 27\mod_1467276354385_21.doc x @ 215503 @ @ 1 The 852-1305 is an industrial ETHERNET switch with 8 10/100/1000BASE-T ports, with autonegotiation and auto-MDI-/MDI-X detection at every port.
WAGO-ETHERNET-Zubehör 852 Device Description 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 4.1.2 Top View Figure 2: Top View of the industrial ECO switch Table 4: Legend for the Figure “Front View of the Industrial Managed Switch” Descrip- Meaning For Details see Section tion Grounding lug Connector (male) for power consumption "Device Description"...
Device Description WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 4.2.2.1 RJ-45 Port The connection to ETHERNET-based fieldbuses is made via the RJ-45 connector (also called “Western plugs”), which are connected to the fieldbus controller via an integrated switch. The integrated switch works in store-and-forward mode and for each port, supports transmission speeds 10/100 Mbit/s as well as the full and half-duplex transmission modes.
Pos : 19.11 /Alle Serien (Allgemeine M odul e)/Übersc hriften/Ebene 2/Anz eigeelemente - Ü bersc hrift 2 @ 4\mod_1240984390875_21.doc x @ 31964 @ 2 @ 1 Display Elements Pos : 19.12 /Serie 852 ( ETHER NET-Z ubehör)/Ger ätebesc hrei bung/Anz eigeelemente/LED-Anz eigen 852-1305 @ 27\mod_1467276540667_21.doc x @ 215521 @ 33 @ 1 The industrial managed switch is equipped with device LEDs and port LEDs. You can see the status of the switch at a quick glance of the device LEDs, while the port LEDs provide information about connection actions.
Page 30
Device Description WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 7: Legend for Figure “Device LEDs” Name Status Description SFP Port Green Lights up when the port is linked. LNK/ACT LED Flashes Data traffic being routed via the port. No proper link established at the port.
WAGO-ETHERNET-Zubehör 852 Device Description 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 4.3.2 Port LEDs Figure 6: Port LEDs Table 8: Legend for Figure “Port LEDs” Name Status Description 1000M 1000BASE T Ports Green Port in operation at 1000 Mbit/s. Flashes Data traffic being routed over the port.
Device Description WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 19.14 /Serie 852 ( ETHER NET-Z ubehör)/Ger ätebesc hrei bung/Bedienel emente/Bedi enel emente 852-1305 @ 27\mod_1467276828638_21.doc x @ 215525 @ 233 @ 1 Operating elements 4.4.1 DIP Switches On the top side of the industrial switch there are DIP switches to configure the alarm and arbiter configurations.
WAGO-ETHERNET-Zubehör 852 Device Description 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX DIP switches let the user manually turn ON/OFF any port, the external alarm, or the redundant power supply. The DIP switch must be “ON” to activate the port alarm function. The default setting is “OFF”.
Device Description WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 19.16 /Serie 852 ( ETHER NET-Z ubehör)/Ger ätebesc hrei bung/Aukl eber/Aufkleber 852-x30x @ 27\mod_1468496819711_21.doc x @ 216873 @ 233 @ 1 Label 4.5.1 Hardware and Software Version There is a label with the “MAC Address” and “Serial NO” on the back of the industrial managed switch.
Connect Devices WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 24.3 /Serie 852 (ETH ERNET-Zubehör)/Ansc hließ en/Ansc hlus s Al ar m 852- x30x @ 24\mod_1452259876829_21.doc x @ 197923 @ 2 @ 1 External Alarm Contact Port The industrial managed switch has an alarm contact connection on the top panel.
WAGO-ETHERNET-Zubehör 852 Connect Devices 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 24.6 /Serie 852 (ETH ERNET-Zubehör)/Ansc hließ en/Ansc hlus s 1000Base- SX/LX, Glasfaser kabel 852- x30x @ 24\mod_1452260347709_21.doc x @ 197927 @ 2 @ 1 1000Base-SX/LX Port, Fiber Optic When connecting a fiber optic cable to a 1000Base-SX/LX port on the industrial managed switch, make sure to use the right connector type (LC) and SFP module.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.1.3 Management Host The management host limits the number of hosts that the switch can manage. There is no “Management Host” in the default settings. Any host can manage the switch via Telnet or web browser. If a user has configured one or more hosts, only those hosts can manage the switch.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX • If the switch does not already know the port for this MAC address, it forwards the frame to all ports. “Port Flooding” (forwarded too often to all ports) can lead to network congestion.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.1.5 Port Mirroring Port mirroring is used on switches to copy sent/received network packets from one or more areas of network monitoring or to send them to another switch port (monitor port). Port mirroring is used in network systems that require monitoring of network traffic as in an IDS (“Intrusion Detection System”).
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Figure 11: Half-Duplex Mode Full-Duplex A full-duplex system (also known as a double-duplex system) can communicate simultaneously in both directions. Fixed-line telephone networks, for example, are full-duplex since both callers can talk and listen at the same time.
Page 48
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Auto MDI/MDIX MDI (“Medium-Dependent Interface”) is part of the transmitter/receiver unit (transceiver) of a network device. Auto-MDIX (“Automatic Medium-Dependent Interface Crossover”) is a network technology integrated in the port that automatically detects the required network cable type (“Straight-Through”...
Page 49
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX For “Flow Control”, the switch sends a pause signal in full-duplex mode to the sending port, causing it to temporarily stop sending signals when the buffer memory of the receiving port is full.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Advanced Settings 7.2.1 Bandwidth Limitation 7.2.1.1 Each egress port supports up to eight “Transmit Queues”. Each “Transmit Queue” contains a list specifying the packet transmission order. Each incoming frame is forwarded to one of the eight “Transmit Queues” of the assigned egress port based on its priority.
Page 51
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX QoS Enhancement You can configure the switch to prioritize data traffic even if the incoming packets are not marked with “IEEE 802.1p Priority Tags” or change the existing “◌ ׅPriority Tags” based on the criteria you select. The switch allows you...
Page 52
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 802.1Q Tag: 2 bytes 2 bytes Tag Protocol Identifier (TPID) Tag Control Information (TCI) 16 bits 3 bits 1 bits 12 bits TPID (0x8100) Priority • TPID (“Tag Protocol Identifier”) A 16-bit field is set to the value of 0x8100 to identify the frame as an “IEEE 802.1Q Tag Frame”.
Page 54
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX manual selection of the actual service parameters when transmitting a data packet through a particular network. Several networks offer service precedence, which treats high precedence traffic as more important than other traffic (generally by accepting only traffic above certain precedence at time of high load).
Page 55
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX If these precedence designations apply to a specific network, it is the responsibility of that network to control access to and the use of those designations. DSCP Priority DSCP Priority DSCP Priority …...
Page 56
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Queuing Algorithms “Queuing Algorithms” can be used to maintain separate “Queues” for packets that can be derived from any single source or any data flow, thus preventing a source from monopolizing the bandwidth.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.1.2 Rate Limitation 7.2.1.2.1 Storm Control A broadcast storm means that the network is overwhelmed with constant broadcast or multicast traffic. Broadcast storms can eventually lead to a complete loss of network connectivity as the packets proliferate.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.2 IGMP Snooping “IGMP Snooping” (“Internet Group Management Protocol Snooping”) is used for multicast data traffic. The switch can passively “snoop” on IGMP packets transmitted between IP multicast routers/switches and IP multicast hosts to learn the IP multicast group membership.
Page 59
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Fast Leave The switch allows you to configure a delay time. When the delay time is expired, the switch deletes the interface from the multicast group. Last Member Query Interval The “Last Member Query Interval” is the maximum response time in group- specific queries sent in response to “Leave Group”...
Page 60
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Port IGMP Querier Mode • Auto The switch uses the port as an “IGMP Query Port” if the port receives “IGMP Query” packets. • Fixed The switch always uses the port(s) as “IGMP Query Port(s)”. This mode is used when connecting an IGMP multicast server to the port(s).
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.2.1 MVR (“Multicast VLAN Registration”) through which a media server can transmit a multicast stream in an individual multicast VLAN and in which the clients receiving the VLAN stream can be located in different VLANs. Clients in different VLANs can join or leave the multicast group simply by sending an “IGMP Join Message”...
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX • Immediate Leave Operation A subscriber sends an “IGMP Leave Message” to the switch to leave the multicast. The subscribers do not need to wait for the switch CPU to send a group-specific “IGMP Query” to the receiver port of the VLAN. The switch immediately deletes the receiver port.
Page 63
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX The switch allows the user to create up to 250 groups. The switch allows the user to create up to 16 MVRs. • “IGMP Snooping” and MVR can be enabled independently. • “IGMP Snooping” and MVR use the same IGMP timer.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.2.2 Multicast Address A multicast address is associated with a group of interested receivers. According to RFC 3171, addresses 224.0.0.0 to 239.255.255.255 (formerly Class D addresses) are reserved as multicast addresses in IPv4.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Figure 15: Multicast Address Table 19: IP Multicast Addresses IP multicast address Description 224.0.0.0 Base address (reserved) 224.0.0.1 “All Hosts Multicast” group that contains all systems on the same network segment. 224.0.0.2 “All Routers Multicast” group that contains all routers on the same network segment.
Page 66
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 19: IP Multicast Addresses IP multicast address Description 224.0.0.18 Virtual Router Redundancy Protocol 224.0.0.19 - 21 IS-IS over IP 224.0.0.22 IGMP Version 3 (“Internet Group Management Protocol”) 224.0.0.102 Hot Standby Router Protocol Version 2 224.0.0.251...
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.3 VLAN A VLAN (“Virtual LAN”) is a group of hosts with a common set of requirements that communicate as if they were attached to a broadcast domain, regardless of their physical location. A VLAN has the same attributes as a physical LAN, but it allows for end stations to be grouped together even if they are not located on the same network switch.
Page 68
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Forwarded Tagged and Untagged Frames • Each port on the switch is capable of forwarding tagged or untagged frames. To forward a frame from an 802.1Q VLAN-aware switch to an 802.1Q VLAN- unaware switch, the switch first decides where to forward the frame and then strips off the VLAN tag.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.3.1 Port Isolation “Port Isolation” is a port-based virtual LAN function. It partitions the switching ports into virtual private domains designated on a per port basis. Data switching outside of the switch's private domain is not allowed. VLAN tag information of the packets is ignored.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.3.2 GARP/GVRP GARP (“Generic Attribute Registration Protocol“) and GVRP (“GARP VLAN Registration Protocol“ or “Generic VLAN Registration Protocol”) are industry- standard protocols described in IEEE 802.1p. GVRP is a GARP application that provides 802.1Q-compliant “VLAN Pruning” and dynamic VLAN creation on “802.1Q Trunk Ports”.
Page 71
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX GVRP Timer: • Join Timer The “Join Timer” specifies the maximum time in milliseconds that interface waits before sending VLAN messages. • Leave Timer The “Leave Timer” specifies the number maximum time in milliseconds an interface waits after receiving a “Leave Message”...
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.3.3 Q-in-Q “Q-in-Q Tunneling” is also known as “VLAN Stacking”. Both of them use 802.1Q double tagging technology. Q-in-Q is used by ISPs (Internet Service Providers) that need TLS (“Transparent LAN Services”) and that have their own set of VLAN, independent of customer VLANs.
Page 73
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Double Tagging Format A VLAN tag (service provider “VLAN Stacking” or customer IEEE 802.1Q) consists of the following three fields: TPID Priority TPID TPID (“Tag Protocol Identifier”) is a standard ETHERNET code identifying the frame and indicating whether the frame contains IEEE 802.1Q tag information.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX VLAN Stacking Port Roles For “VLAN Stacking”, each port can have one of three “roles”: Normal, “Access Port” or “Tunnel Port”. • Select “normal” for normal (no “VLAN Stacking”) IEEE 802.1Q frame switching.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Figure 16: Port-Based Q-in-Q This example shows how to configure switch A with port 1 on the switch to tag incoming frames with the service provider’s VID of 200 (ports are connected to customer X network) and configure port 7 to the service provider’s VID of 100...
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.4 DHCP Relay Because the “DHCPDISCOVER” message is a broadcast message and broadcasts only cross other segments when they are explicitly routed, you might have to configure a “DHCP Relay Agent” on the router interface so that all “DHCPDISCOVER”...
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Figure 18: Application 1 (via a Router) Application 2 (local in different VLANs) • DHCP client 1 and DHCP client 2 are in different VLANs. However, they receive IP address from the same DHCP server.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.5 DHCP Relay Option 82 “DHCP Option 82” (“DHCP Relay Agent Information Option”). Option 82 was designed to allow a “DHCP Relay Agent” to insert circuit-specific information into a request that is being forwarded to a DHCP server. Specifically, the option works by setting two sub-options: “Circuit ID”...
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Option Frame Format Table 20: Option Frame Format Code Agent Information Field … The “Agent Information Field” consists of a sequence of SubOpt/Length/Value tuples for each sub-option, encoded in the following manner: Table 21: Option Frame Format...
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.6 Dual Ring The “Dual Ring” function can be used to connect 2 neighboring rings to each other on a switch without needing additional ports or cables. This configuration reduces the total number of required ports and wiring costs are saved because no additional wiring is required.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.7 ERPS The ERPS (“ETHERNET Ring Protection Switching”) function implements a protection switching mechanism for ETHERNET layer ring topologies according to ITU-T standard G.8032. The ERP (“ETHERNET Ring Protection”) protects ETHERNET traffic in a ring topology and ensures that no loops are within the ring in the ETHERNET later.
Page 82
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Guard Timer All ring subscribers use a “Guard Timer”. It prevents the possibility of forming a closed loop and prevents ring subscribers from using outdated R-APS messages. The “Guard Timer” is enabled if a ring subscriber received information on a local switching request, such as after SF (“Switch Fail”), MS (“Manual Switch”) or FS...
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Control VLAN The “Control VLAN” is a domain in which only ERPS control packets are transmitted. Because no other packets are transmitted in the VLAN, there are no delays for the ERPS. Therefore, when configuring a control VLAN for a ring, make sure it is a new VLAN.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.8 Dual Homing “Dual Homing” is a network topology in which a device is connected to the network by way of two independent access points (“Points of Attachment”). One access point establishes the primary connection, and the other is a reserve if the primary connection fails.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.9 Link Aggregation 7.2.9.1 Static Trunk “Ling Aggregation” (also called “Trunking”), parallel link bundling) is the grouping of physical ports into one logical ling with higher capacity. When bundling ports, it can be more cost effective to use multiple lower-speed links than to underutilize a high-speed, but expensive “Port Link”.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX System Priority LACP system priority is used to determine membership in an LAG (“Link Aggregation Group”) and identifies the device for other switches during LAG negotiations. The switch with the lowest system priority (and lowest port number if system priority is the same) becomes the LACP “Server”.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.11 Loop Detection “Loop Detection” handles problems with loops in the network periphery. These problems can occur if a port is connected to a switch that is in a loop state. A loop state occurs as a result of user error.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.12 Jet Ring Setting up the Jet Ring function (redundant connection) in a network better protects critical connections against errors and network loops. In addition, network downtime is reduced to less than 300 ms.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.2.13 The (R)STP (“(Rapid) Spanning Tree Protocol)”) can detect and stop network loops, as well as provide “Backup Links” between switches, bridges or routers. It allows a switch to interact with other (R)STP-compliant switches in the network to ensure that only one path exists between any two stations on the network.
Page 90
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX “Forwarding” • The port is in normal operating mode and receives and sends data. STP still monitors incoming BPDUs that would indicate that the port should return to the “Blocking” state to prevent a loop.
Page 92
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX After a bridge determines the lowest cost “Spanning Tree” with STP, it enables the “Root Port” and “Designated Ports” for connected LANs, and disables all other ports that participate in STP. Network packets are therefore only forwarded between enabled ports, eliminating any possible network loops.
Page 93
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Port Priority The port priority is configured on the switch. A low numeric value indicates a high priority. A port with lower priority is more likely to be blocked by STP if a network loop is detected.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX MSTP The MSTP (“Multiple Spanning Tree Protocol”) is an RSTP extension. It allows different spanning tree instances in conjunction with VLANs (“Virtual Local Area Networks”). For a VLAN or group of VLANs, STP instances can be created independently that user their own different spanning trees within a LAN.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Security 7.3.1 IP Source Guard “IP Source Guard” is a security function that restricts IP traffic on untrusted Layer2 ports by filtering traffic based on a “DHCP Snooping” database connection or a manually configured IP source connection. This function helps prevent access such as “IP Snooping”...
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.3.1.1 DHCP Snooping “DHCP Snooping” is a DHCP security function that increases network security by filtering untrusted DHCP messages and creating and using a “DHCP Snooping” database connection (also called “DHCP Snooping” binding table).
Page 97
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX “Untrusted Ports” are connected to subscribers. The switch discards DHCP packets from untrusted ports in the following situations: • The packet is a DHCP server packet (e.g., “OFFER”, “ACK” or “NACK”). • The source MAC address and source IP address in a packet do not match any of the current bindings.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX The main purposes of the “DHCP Snooping” are: To create and maintain a binding table for the ARP Inspection function. To filter packets from DHCP servers that are connected to an “Untrusted Port”.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.3.1.3 ARP Inspection The dynamic “ARP Inspection” (“Address Resolution Protocol Inspection”) is a security function in which ARP packets are inspected in a network. Dynamic ARP inspections validates the packet by performing IP-to-MAC address binding inspection stored in a trusted database (the “DHCP Snooping”...
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.3.1.3.1 Filter Table Dynamic ARP inspections validates the packet by performing IP-to-MAC address binding inspection stored in a trusted database (the “DHCP Snooping” database) before forwarding the packet. If the switch detects an unauthorized ARP packet, it automatically creates a MAC address filter to block traffic from the source MAC address and the source VLAN ID of the packet.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.3.2 Access Control List (ACL) The ACL (“Access Control List”) is a list of permissions attached to an object. The list specifies who or what is allowed to access an object and what operations are allowed to be performed on the object.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.3.3 802.1x IEEE 802.1X is an IEEE Standard for port-based Network Access Control (“port” meaning a single point of attachment to the LAN infrastructure). It is part of the IEEE 802.1 group of networking protocols. It provides an authentication mechanism to devices wishing to attach to a LAN, either establishing a point-to- point connection or preventing it if authentication fails.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX RADIUS Server The RADIUS server (“Remote Authentication Dial-In User Service”) is a client- server-based security protocol for authentication and to control network access permissions. The RADIUS server operates using the Challenge/Response process and supports central administration of user data, such as user ID, passwords, phone, access rights and account data, and consists of an accounting and authentication protocol.
Page 104
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Local User Accounts By storing user profiles locally on the switch, it can authenticate users without interacting with the network authentication server. However, there is a limit on the number of users that can be authenticated in this way.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Quiet Period • The “Quiet Period” function is used to specify the time a client has to wait before the next authentication attempt. This prevents the switch from becoming overloaded with continuous authentication attempts from the client.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Monitor 7.4.1 Alarm Information This function alerts the network administrator to any abnormal network situations. Alarm DIP Switches The alarm DIP switches allow users to configure if an alarm message should be sent when a corresponding event occurs.
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.4.4.1 DDM (“Dynamic Device Mapping”) is a technology for KVM switches with USB ports that are sometimes used as an alternative to standard USB keyboard and mouse emulation. 7.4.5 Traffic Monitor The “Traffic Monitor” function can be used to enable or disable a specific port or the switch globally.
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Management 7.5.1 SNMP The SNMP (“Simple Network Management Protocol”) is used in network management systems to monitor the state of attached devices that require the attention of an administrator. SNMP is a component of the “Internet Protocol Suite”...
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.5.2 SNMP Trap A trap is an unsolicited message from an agent to the manager that an event has occurred. The SNMP Manager that receives the tap can ask for more information. 7.5.3 Auto Provision The “Auto Provision”...
Page 110
Enhanced Features WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX If “Global_Configuration_State =1”, please download the specific configuration file and update the configuration. If not, continue to Step 10. The name is: “Model_Name _” with 12-bit MAC digits, e.g., “MEN- 5210_00e04c8196b9.txt”. If the configuration is updated successfully and “Specific_Configuration_Reboot =1”, “reboot_flag=1”...
WAGO-ETHERNET-Zubehör 852 Enhanced Features 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 7.5.4 Mail Alarm The “Mail Alarm” function sends an e-mail trap to a previously defined administrator when certain events occur. The events are listed below: System Reboot: The system performs a warm or cold start.
WAGO-ETHERNET-Zubehör 852 Configuration 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 28.4 /Serie 852 (ETH ERNET-Zubehör)/Konfigurieren/T el net- Por t @ 25\mod_1453208173100_21.doc x @ 198621 @ 3 @ 1 8.1.1 Telnet Port Connect the computer to one of the ETHERNET ports. Open a Telnet session to the switch’s IP address. If this is your first login, use the default values.
Configuration WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 28.6 /Serie 852 (ETH ERNET-Zubehör)/Konfigurieren/Kons olenport @ 25\mod_1453203786134_21.doc x @ 198615 @ 3 @ 1 8.1.2 Console Port Before accessing the integrated management agent of the industrial managed switch via a network connection, you first have to configure it via a local connection or the BOOTP protocol with the default IP address, a subnet mask and a standard gateway.
Firmware version 01: User = “admin”, password = “Wago1951” Firmware version 02: User = “admin”, password = “wago” The start page of WBM loads. Make the wanted settings. Press [Apply] or [Update] or press [Delete] or [Discard] to discard your changes.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX You can access the respective WBM pages via the links in the navigation bar: Table 29: Overview - Navigation Links and WBM Pages Navigation Links and WBM Pages ...
Page 117
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX [Security] [IP Source Guard] • DHCP Snooping Binding Table • • ARP Inspection • Access Control List • 802.1x • Port Security [Monitor] • Alarm •...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX System Status 9.1.1 System Informationen Figure 27: WBM “System Information” Page Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 30: WBM “System Information” Page Parameters Description Model Name This display field shows the model name of the switch. Host Name This display field shows the host name of the switch.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Basic Settings 9.2.1 General Settings 9.2.1.1 System Figure 28: WBM Page, “General Settings” – “System” Tab Table 31: WBM Page, “General Settings” – “System” Tab System Settings Parameters...
Page 121
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 31: WBM Page, “General Settings” – “System” Tab IPv6 Settings Parameters Default Description DHCP Client Disable Select “Disable” in the selection box if you want to manually configure the IP address of the switch.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.2.1.2 Jumbo Frame Additional Information Please refer to the section “Function Description” for more information on “Jumbo Frame”. Figure 29: WBM Page, “General” – “Jumbo Frame” Tab Table 32: WBM Page, “General” – “Jumbo Frame” Tab...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.2.1.3 SNTP Additional Information Please refer to the section “Function Description” for more information on “SNTP” (Simple Network Time Protocol). Figure 30: WBM Page, “General” – “SNTP” Tab Manual 1.1.0...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 33: WBM Page, “General” – “SNTP” Tab Current Time and Date Parameters Default Description Current Time This field displays the current time if you open or refresh the menu.
Page 125
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 33: WBM Page, “General” – “SNTP” Tab Daylight Saving Settings Parameters Default Description State Disable Select “Disable” if you do not want to use daylight savings time.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.2.1.4 Management Host Additional Information Please refer to the section “Function Description” for more information on “Management Host”. Figure 31: WBM Page, “General” – “Management Host” Tab Table 34: WBM Page, “General” – “Management Host” Tab...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.2.2 MAC Management Additional Information Please refer to the section “Function Description” for more information on “MAC Management”. 9.2.2.1 Static MAC Settings Additional Information Please refer to the section “Function Description” for more information on “Static MAC Settings”...
Page 128
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 35: WBM Page, “MAC Management” – “Static MAC Settings” Tab Static MAC Table Parameters Default Description MAC Address This column displays the manually entered MAC address entries.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.2.2.3 Age Time Setting Figure 34: WBM Page, “MAC Management” – “Age Time Setting” Tab Table 37: WBM Page, “MAC Management” – “Age Time Setting” Tab Age Time Setting...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.2.2.4 Refusal MAC Settings Additional Information Please refer to the section “Function Description” for more information on “Refusal MAC Settings”. Maximum number of MAC blacklist entries Up to 20 entries can be configured.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.2.3 Port Mirroring Additional Information Please refer to the section “Function Description” for more information on “Port Mirroring”. Monitor Port The monitor port cannot be a member of any “Truck Port” group.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 39: WBM “Port Mirroring” Page Port Mirroring Settings Parameters Default Description State Disable Select “Disable” to disable the “Port Mirroring”. Enable Select “Enable” to enable the “Port Mirroring”.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 40: WBM Page, “Port Settings” – “General Settings” Tab Port Settings Parameters Default Description Port From: Select a port or port range that you want to configure.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.2.4.2 Information Figure 38: WBM Page, “Port Settings” – “Information” Tab Table 41: WBM Page, “Port Settings” – “Information” Tab Port Settings Parameters Default Description Port From: Select a port or port range that you want to display.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Advanced Settings 9.3.1 Bandwidth Control 9.3.1.1 Additional Information More information about “QoS” (Quality of Service) is available in the section “Function Description”. 9.3.1.1.1 Port Priority Figure 39: WBM “QoS” Page – “Port Priority” Tab Table 42: WBM “QoS”...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 46: WBM “QoS” Page – “Schedule Mode” Tab Schedule Mode Settings Parameters Default Description Schedule Mode High First In the selection box, select “Strict Priority Queuing (SPQ)” if you want to process the hardware priority (SPQ) queues sequentially.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.1.2 Rate Limitation 9.3.1.2.1 Storm Control Additional Information Please refer to the section “Function Description” for more information on “Storm Control”. Figure 43: WBM “Rate Limitation” Page – “Storm Control” Tab Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 47: WBM “Rate Limitation” Page – “Storm Control” Tab Storm Control Settings Parameters Default Description Port From: Select a port or port range in the selection box to configure the “Storm Control”...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.1.2.2 Bandwidth Limitation Additional Information Please refer to the section “Function Description” for more information on “Bandwidth Limitation”. Figure 44: WBM “Rate Limitation” Page – “Bandwidth Limitation” Tab Table 48: WBM “Rate Limitation”...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.2 IGMP Snooping Additional Information Please refer to the section “Function Description” for more information on “IGMP Snooping” (Internet Group Management Protocol Snooping). 9.3.2.1 IGMP Snooping 9.3.2.1.1 General Settings Figure 45: WBM “IGMP Snooping”...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 50: WBM “IGMP Snooping” Page – “Port Settings” Tab Port Settings Parameters Default Description Port From: In this selection box, select a port or port range to configure the “Port Settings”.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.2.3 Additional Information Please refer to the section “Function Description” for more information on “MVR (Multicast VLAN Registration). 9.3.2.3.1 MVR Settings Figure 51: WBM “MVR” Page – “MVR Settings” Tab Manual 1.1.0...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 55: WBM “MVR” Page – “MVR Settings” Tab MVR Settings Parameters Default Description VLAN ID Enter the VLAN ID in the input field. Name Enter the name for the MVR in the input field.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.2.4 Multicast Address Additional Information Please refer to the section “Function Description” for more information on “Multicast Address”. Figure 53: WBM “Multicast Address” Page Table 57: WBM “Multicast Address” Page...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.2.5 Multicast IP Statistics Figure 54: WBM “Multicast IP Statistics” Page Table 58: WBM “Multicast IP Statistics” Page Multicast IP Table Parameters Default Description Index 1 … 10 This column displays the number of entries.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.3 VLAN Additional Information Please refer to the section “Function Description” for more information on “VLAN” (Virtual Local Area Network). 9.3.3.1 Port Isolation Additional Information Please refer to the section “Function Description” for more information on “Port Isolation”.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 59: WBM “Port Isolation” Page Port Isolation Settings Parameters Default Description Port From: Select a port or port range in the selection box for which you want to configure the “Port Isolation”...
Page 161
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 60: WBM “VLAN” Page – “VLAN Settings” Tab VLAN List Parameters Default Description VLAN ID 1 … 4094 This column displays the index number of the VLAN entry.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.3.2.2 Tag Settings Figure 57: WBM “VLAN” Page – “Tag Settings” Tab Table 61: WBM “VLAN” Page – “TAG Settings” Tab Tag Settings Parameters Default Description VLAN-ID From: Enter the VLAN ID for this entry in the input field.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 62: WBM “VLAN” Page – “Port Settings” Tab Port Settings Parameters Default Description Port From: Select a port or port range in the selection box to configure the “Port Settings”.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.3.3 GARP/GVRP Additional Information Please refer to the section “Function Description” for more information on “GARP/GVRP” (Generic Attribute Registration Protocol/GARP VLAN Registration Protocol or Generic VLAN Registration Protocol).
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.3.3.2 GARP Timer Size of the “leave”, “join”, “leave” and “leaveall” values The value for “leave” must be three times the value for “join” (leave >= join x 3).
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 64: WBM “GARP VLAN Registration Protocol” Page – “GVRP Timer” Tab GARP Timer Settings Parameters Default Description Port From: Select a port or port range in the selection box to configure the GARP timer.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.3.4 MAC VLAN Figure 61: WBM “MAC VLAN” Page Table 65: WBM “MAC VLAN” Page MAC VLAN Settings Parameters Default Description MAC Address Enter the first three or more bytes of the MAC address in the input field.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.3.5 Protocol VLAN Figure 62: WBM “Protocol VLAN” Page Table 66: WBM “Protocol VLAN” Page Protocol VLAN Settings Parameters Default Description Frame Type EthertnetII Select “EthernetII” in the selection box if you want to configure this frame type.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.3.6 Q-in-Q Additional Information Please refer to the section “Function Description” for more information on “Q-in- Q”. 9.3.3.6.1 VLAN Stacking Figure 63: WBM “Q-in-Q” Page – “VLAN Stacking” Tab Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.3.6.2 Port-based Q-in-Q Figure 64: WBM “Q-in-Q” Page – “Port-based Q-in-Q” Tab Table 68: WBM “Q-in-Q” Page – “Port-based Q-in-Q” Tab Port-based Q-in-Q Parameters Default Description Port From: Select a port or port range in the selection box to configure the “Q-in-Q”.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 69: WBM “Q-in-Q” Page – “Selective Q-in-Q” Tab Selective Q-in-Q Setting Parameters Default Description Name Enter the name for the selective Q-in-Q profile in the input field.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.4 DHCP Relay Additional Information Please refer to the section “Function Description” for more information on “DHCP Relay” (Dynamic Host Configuration Protocol Relay). Figure 66: WBM “DHCP Relay” Page Table 70: WBM “DHCP Relay”...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.6 Dual Homing Additional Information Please refer to the section “Function Description” for more information on “Dual Homing”. Figure 68: WBM “Dual Homing” Page Table 72: WBM “Dual Homing” Page...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.7 Dual Ring Additional Information Please refer to the section “Function Description” for more information on “Dual Ring”. Figure 69: WBM “Dual Ring” Page Manual 1.1.0...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 73: WBM “Dual Ring” Page Dual Ring Settings Parameters Default Description State Disable Select “Disable” in the selection box to disable this function. Enable Select “Enable” to enable “Dual ring”.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.8 ERPS Additional Information Please refer to the section “Function Description” for more information on “ERPS” (ETHERNET Ring Protection Switching). 9.3.8.1 Ring Settings Figure 70: WBM “ERPS” Page – “Ring Settings” Tab Manual 1.1.0...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 74: WBM “ERPS” Page – “Ring Settings” Tab ERPS Global Settings Parameters Default Description Global State Disable Select “Disable” in the selection box to disable the ERPS function.
Page 183
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 74: WBM “ERPS” Page – “Ring Settings” Tab Guard Timer (ms) Enter the value for the “Guard Timer” for the ring in (10~2000) this input field. Valid range: 10 … 2000 ms.
Page 184
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 74: WBM “ERPS” Page – “Ring Settings” Tab Left Port None This field displays the port number of the left port. 1 … 10 Right Port None This field displays the port number of the right port.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.9 Link Aggregation 9.3.9.1 Static Trunk Additional Information Please refer to the section “Function Description” for more information on “Static Trunk”. Figure 72: WBM “Link Aggregation” Page – “Static Trunk” Tab Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 76: WBM “Link Aggregation” Page – “Static Trunk” Tab Static Trunk Settings Parameters Default Description Group 1 … Group State Select a group ID for the “Trunk Group” (a logical Group 6 ling containing multiple ports) in the selection box.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.9.2 LACP Additional Information Please refer to the section “Function Description” for more information on “LACP” (Link Aggregation Control Protocol). Figure 73: WBM “Link Aggregation” Page – “LACP” Tab Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 77: WBM “Link Aggregation” Page – “LACP” Tab LACP Settings Parameters Default Description State Disable Select “Disable” in the selection box if you do not want to use LACP.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 78: WBM “Link Aggregation” Page – “LACP Info.” Tab LACP Information Parameters Default Description Group ID Select an LACP group that you want to view. Neighbor Informationen...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.10 LLDP Additional Information Please refer to the section “Function Description” for more information on “LLDP” (Link Layer Discovery Protocol). 9.3.10.1 Settings Figure 75: WBM “LLDP” Page – “Settings” Tab Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 79: WBM “LLDP” Page – “Settings” Tab LLDP Settings Parameters Default Description State Disable Select “Disable” in the selection box to disable this function. Enable Select “Enable” in the selection box to enable the LLDP function.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.10.2 Neighbor Figure 76: WBM “LLDP” Page – “Neighbor” Tab Table 80: WBM “LLDP” Page – “Neighbor” Tab LLDP Neighbor Information Parameters Default Description Port Select “All” in the selection box if you want to display information from all neighboring ports.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.11 Loop Detection Additional Information Please refer to the section “Function Description” for more information on “Loop Detection”. Figure 77: WBM “Loop Detection” Page Manual 1.1.0...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 81: WBM “Loop Detection” Page Loop Detection Settings Parameters Default Description Status Disable Select “Disable” in the selection box to disable this function. Enable Select “Enable” in the selection box to enable this function.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.12 Jet Ring Figure 78: WBM “Jet Ring” Page Table 82: WBM “Jet Ring” Page Jet Ring Setting Parameters Default Description State Disable In this selection box, select “Disable” to disable the “Jet Ring”...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.14 Additional Information Please refer to the section “Function Description” for more information on “STP” (Spanning Tree Protocol). 9.3.14.1 General Settings Figure 80: WBM “STP” Page – “General Settings” Tab Manual 1.1.0...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 84: WBM “STP” Page – “General Settings” Tab Spanning Tree Protocol Settings Parameters Default Description State Disable Select “Disable” in the selection box to disable this function.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 85: WBM “STP” Page – “Port Parameters” Tab Port Parameters Settings Parameters Default Description Port From: Select a port or port range in the selection box to configure the “STP Function”.
Page 203
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 85: WBM “STP” Page – “Port Parameters” Tab Port Status Parameters Default Description Port 1 … 10 This column displays the port numbers. Active Enable This column displays the status of the STP function.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 86: WBM “STP” Page – “STP Status” Tab Current Root Status Parameters Default Description MAC Address This field displays the MAC address of the “Root Bridge”. Priority This field displays the priority of the “Root Bridge”.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.3.15 Xpress Ring Additional Information Please refer to the section “Function Description” for more information on “Xpress Ring”. Figure 83: WBM “Xpress Ring” Page Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 87: WBM “Xpress Ring” Page Xpress Ring Settings Parameters Default Description Global State Disabled Select “Disable” in the selection box to disable the “Xpress Ring” function. Enabled Select “Enable”...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Security 9.4.1 IP Source Guard Additional Information Please refer to the section “Function Description” for more information on “IP Source Guard”. 9.4.1.1 DHCP Snooping Additional Information Please refer to the section “Function Description” for more information on “DHCP Snooping”...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 88: WBM “DHCP Snooping” Page – “DHCP Snooping” Tab DHCP Snooping Settings Parameters Default Description State Disable Select “Disable” in the selection box if you do not want to use this function.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.4.1.1.3 Server Screening Additional Information Please refer to the section “Function Description” for more information on “Server Screening”. Figure 86: WBM “DHCP Snooping” Page – “Server Screening” Tab Table 90: WBM “DHCP Snooping”...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.4.1.2 Binding Table Additional Information Please refer to the section “Function Description” for more information on “Binding Table”. 9.4.1.2.1 Static Entry Figure 87: WBM “Binding Table” Page – “Static Entry” Tab Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 91: WBM “Binding Table” Page – “Static Entry” Tab Static Entry Settings Parameters Default Description MAC Address Enter the source MAC address for the binding in this input field.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.4.1.3 ARP Inspection Additional Information Please refer to the section “Function Description” for more information on “ARP Inspection” (“Address Resolution Protocol Inspection”). 9.4.1.3.1 ARP Inspection Figure 89: WBM “ARP Inspection” Page – “ARP Inspection” Tab Manual 1.1.0...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 93: WBM “ARP Inspection” Page – “ARP Inspection” Tab ARP Inspection Settings Parameters Default Description State Disable Select “Disable” in the selection box if you want to disable ARP inspection on the switch.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.4.1.3.2 Filter Table Additional Information Please refer to the section “Function Description” for more information on “Filter Table”. Figure 90: WBM “ARP Inspection” Page – “Filter Table” Tab Table 94: WBM “ARP Inspection”...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.4.2 Access Control List Additional Information Please refer to the section “Function Description” for more information on “Access Control”. Figure 91: WBM “Access Control List” Page Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 95: WBM “Access Control List” Page Access Control List Settings Parameters Default Description Profile Name Enter the name of the profile in the input field. Action Disable Select “Disable”...
Page 220
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 95: WBM “Access Control List” Page Source IP Select “any” in the selection box, so every IP address is valid. Other Select “Other” in the selection box to enter the source IP address in the access control list.
Page 221
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 95: WBM “Access Control List” Page Destination MAC This field displays the destination MAC address. Other Mask of Destination MAC This field displays the destination MAC ID of the bitmap mask.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.4.3 802.1x Additional Information Please refer to the section “Function Description” for more information on the “IEEE 802.1x” standard. 9.4.3.1 Global Settings Figure 92: WBM “802.1x” Page – “Global Settings” Tab Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 96: WBM “802.1x” Page – “Global Settings” Tab Global Settings Parameters Default Description State Disable Select “Disable” in the selection box to disable 802.1x authentication on the switch.
Page 224
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 96: WBM “802.1x” Page – “Global Settings” Tab Secondary This is the back-up server that is only used if the Radius primary RADIUS server fails. Server In the input field, enter the IP address of the external RADIUS server in decimal-point notation.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.4.3.2 Port Settings Figure 93: WBM “802.1x” Page – “Port Settings” Tab Manual 1.1.0...
Page 226
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 97: WBM “802.1x” Page – “Port Settings” Tab Port Settings Parameters Default Description Port From: Select a port or port range in the selection box to configure the “Port Settings”.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 97: WBM “802.1x” Page – “Port Settings” Tab Reset to Default No custom settings for 802.1x port authentication are reset to the default values. The custom settings for 802.1x port authentication are reset to the default values.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.4.4 Port Security Additional Information Please refer to the section “Function Description” for more information on “Port Security”. Figure 94: WBM “Port Security” Page Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 98: WBM “Port Security” Page Port Security Settings Parameters Default Description Port Security Disable Select “Disable” in the selection box to disable port security on the switch.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 28.8.7 /Serie 852 (ETH ERNET-Z ubehör)/Konfigurieren/M oni tor 852- 0303 @ 27\mod_1468312186200_21.doc x @ 216538 @ 23333333 @ 1 Monitor Monitor 9.5.1 Alarm Information Additional Information Please refer to the section “Function Description”...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.5.2 Monitor Information Additional Information Please refer to the section “Function Description” for more information on the “Monitor Information”. Figure 96: WBM “Monitor Information” Page Manual 1.1.0...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 100: WBM “Monitor Information” Page Hardware Information Parameters Default Description Temperature unit Celsius (C) Select “Celsius (C)” in the selection box if you want to display the temperature in Celsius.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.5.3 Port Statistics Additional Information Please refer to the section “Function Description” for more information on the “Port Statistics”. Figure 97: WBM “Port Statistics” Page Table 101: WBM “Port Statistics” Page...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.5.4 Port Utilization Additional Information Please refer to the section “Function Description” for more information on the “Port Utilization”. Figure 98: WBM “Port Utilization” Page Table 102: WBM “Port Utilization” Page...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.5.5 RMON Statistics Additional Information Please refer to the section “Function Description” for more information on the “RMON Statistics”. Figure 99: WBM “RMON Statistics” Page Manual 1.1.0...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 103: WBM “RMON Statistics” Page RMON Statistics Parameters Default Description Port Select “-” in the selection box, if you do not want to view any statistics. 1 … 10 In the selection box, select a port or all ports to display their RMON statistics.
Page 237
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 103: WBM “RMON Statistics” Page Outbound Total Octets This display field shows the number of data packets sent from the port. Broadcast This display field shows the number of broadcast Pkts packets sent from the port.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 104: WBM “SFP Information” Page SFP Information Parameters Default Description Port -, 9, 10 Select a port number to configure. SFP Information Parameters Default Description Fiber Cable This display field shows if the fiber optic cable is connected.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.5.7 Traffic Monitor Additional Information Please refer to the section “Function Description” for more information on the “Traffic Monitor”. Figure 101: WBM “Traffic Monitor” Page Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 105: WBM “Traffic Monitor” Page Traffic Monitor Settings Parameters Default Description Status Disable Select “Switch OFF” in the selection box to disable the “Traffic Monitor” function globally.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.6.1.1.2 Community Name Figure 103: WBM Page, “SNMP” – “Community Name” Tab Table 107: WBM Page, “SNMP” – “Community Name” Tab Community Name Settings Parameters Default Description Community String Enter the “Community String”...
Page 244
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 107: WBM Page, “SNMP” – “Community Name” Tab Community Name List Parameters Default Description This column displays the “Community” number. It is used for identification only. Click a number to modify the setting for a specific “Community”.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.6.2 Auto Provision Additional Information Please refer to the section “Function Description” for more information on “Auto Provision”. Figure 105: WBM “Auto Provision” Page Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 109: WBM “Auto Provision” Page Auto Provision Settings Parameters Default Description State Disable Select “Disable” in the selection box to disable “Auto Provision” function on the switch.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.6.3 Mail Alarm Additional Information Please refer to the section “Function Description” for more information on “Mail Alarm”. Figure 106: WBM “Mail Alarm” Page Manual 1.1.0...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 110: WBM “Mail Alarm” Page Mail Alarm Settings Parameters Default Description State Disable Select “Disable” in the selection box to disable the “Mail Alarm” function. Enable Select “Enable” in the selection box to enable the “Mail Alarm”...
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.6.4 Maintenance 9.6.4.1 Configuration Figure 107: WBM Page, “Maintenance” – “Configuration” Tab Save Configuration • Click the [Save] button to save the current settings in NV-RAM (Flash). Upload and Download the Configuration Execute the following steps to save the configuration file to your PC.
Page 251
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Reset Configuration Click the [Reset] button to reset the switch configuration to the factory • default. Configuration Status “The configurations have been changed” indicates that changes have been made to the configurations.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.6.4.2 Firmware Figure 108: WBM Page, “Maintenance” – “Firmware” Tab Firmware Update Execute the following steps to update the switch's firmware. Click the [Select file] button. The file selection dialog opens. Select the respective firmware file.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.6.4.3 Reboot Figure 109: WBM Page, “Maintenance” – “Reboot” Tab Reboot The “Reboot” function allows you to restart the switch without physically turning the power off. Follow the steps below to reboot the switch.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.6.5 System Log The “syslog” function records various system information for “Debugging”. Each log entry records one of the following levels: - Alert - Critical - Error - Warning...
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 111: WBM “System Log” Page Syslog Server Settings Parameters Default Description Server IP IPv4 In the “IPv4” selection box, choose if you want to select this version of the Internet protocol.
Configuring in the Web-Based Management System (WBM) WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 9.6.6 User Account The switch allows users to create up to six user accounts. The user name and password must be a combination of numbers or letters. The last admin account cannot be deleted.
WAGO-ETHERNET-Zubehör 852 Configuring in the Web-Based Management System (WBM) 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 112: WBM “User Account” Page User Account Settings Parameters Default Description User Name Enter a new or modify the existing user name in the input field. User Password Enter a new or modify an existing password in the input field.
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 30.6 /Serie 852 (ETH ERNET-Zubehör)/Anhang/CLI- Konfigur ati on @ 26\mod_1465480732374_21.doc x @ 212168 @ 23434444444434444444455445444444443444444443444443444444 @ 1 10.3 Configuring in the Command Line Interface (CLI) 10.3.1 System Status 10.3.1.1 System Information Table 114: CLI “System Information” Configuration...
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.2.3 SNTP Table 117: CLI “SNTP” Configuration Node Command Description enable show time This command displays the current time and date configurations. configure time This command sets the current time of the switch. HOUR:MINUTE:SECON...
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.2.4 Management Host Table 118: CLI “Management Host” Configuration Node Command Description enable show interface eth0 The command displays the all eth0 interface configurations. eth0 show The command displays the all eth0 interface configurations.
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.2.6 Blackhole MAC Table 120: CLI “Blackhole MAC” Configuration Node Command Description enable show mac-address-table This command displays the current rejected MAC refusal address only. configure mac-address-table refusal This command configures the rejection of a MAC MACADDR vlan address in a specific VLAN.
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.2.8 Port Settings Table 122: CLI “Port Settings” Configuration Node Command Description enable show interface IFNAME This command displays the current port configurations. interface show This command displays the current port configurations. interface loopback (none | phy) This command specifies the “Loopback”...
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.3 Advanced Settings 10.3.3.1 Bandwidth Control 10.3.3.2 Table 123: CLI “QoS” Configuration Node Command Description enable show queue cos-map This command displays the current 802.1p priority mapping to the “Service Queue”. enable show qos mode This command displays the current IEEE 802.1p...
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.3.6 Table 127: CLI “MVR” Configuration Node Command Description enable show mvr This command displays the current MVR configurations. enable show mvr vlan VLANID This command displays the current MVR configurations of the specific VLAN.
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.3.9 GARP/GVRP Table 131: CLI “GARP/GVRP” Configuration Node Command Description enable show gvrp configuration This command displays the GVRP configurations. enable show gvrp statistics This command displays the GVRP configurations for one port or all ports.
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.3.14 LACP Table 136: CLI “LACP” Configuration Node Command Description enable show trunk The command displays the current configuration for “Trunking”. enable show lacp counters This command displays the LACP counters for the [GROUP_ID] specific group or all groups.
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.3.15 LLDP Table 137: CLI “LLDP” Configuration Node Command Description enable show lldp This command displays the LLDP configurations. enable show lldp neighbor This command displays all information of port neighbors. configure lldp (disable | enable) This command globally enables / disables the LLDP function on the switch.
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.3.16 Loop Detection Table 138: CLI “Loop Detection” Configuration Node Command Description enable show loop-detection This command displays the current configuration for “Loop Detection”. configure loop-detection (disable | This command disables / enables “Loop Detection”...
Page 279
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.3.17 STP Table 139: CLI “STP” Configuration Node Command Description enable show spanning-tree active This command only displays STP information for active ports. enable show spanning-tree This command only displays STP information for blockedports blocked ports.
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 139: CLI “STP” Configuration Node Command Description interface spanning-tree cost This command configures the costs for the specific VALUE port. Cost range: 16-bit-based value range of 1 to 65,535, 32-bit-based value range of 1 to 200,000,000.
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.4.2 Server Screening Table 142: CLI “Server Screening” Configuration Node Command Description enable show dhcp-snooping This command displays the IP address of the valid server DHCP server. configure dhcp-snooping server This command configures the IP address of a valid IPADDR DHCP server.
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.4.4 ARP Inspection Table 144: CLI “ARP Inspection” Configuration Node Command Description enable show arp-inspection This command displays the current configurations for the ARP Inspection. configure arp-inspection (disable | This command disables / enables the ARP Inspection enable) function on the switch.
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.4.6 Access Control List Table 146: CLI “Access Control List” Configuration Node Command Description enable show access-list This command displays all access control profiles. configure access-list STRING This command creates a new access control profile.
Page 285
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 146: CLI “Access Control List” Configuration Node Command Description L4-destination-port PORT This command configures the UDP/TCP destination port for the profile. no l4-destination-port This command deletes the UDP/TCP destination port from the profile.
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.4.7 802.1x Table 147: CLI “802.1x” Configuration Node Command Description enable show dot1x This command displays the current 802.1x configurations. enable show dot1x username This command displays the current user accounts for local authentication.
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 147: CLI “802.1x” Configuration Node Command Description interface dot1x timeout server- This command configures the server timeout value timeout on the port. interface dot1x timeout reauth- This command configures the authentication interval period value on the port.
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.6.2 Auto Provision Table 155: CLI “Auto Provision” Configuration Node Command Description auto-provision show This command displays the current configurations for the “Auto Provision”. auto-provision active (enable | disable) This command enables / disables the “Auto Provision”...
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.6.4 Maintenance Table 157: CLI “Maintenance” Configuration Node Command Description configure reboot This command reboots the system. configure reload default-config This command resets the system configuration to the default settings. Note: The system automatically reboots to apply the configurations.
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX 10.3.6.5 System Log Table 158: CLI “System Log” Configuration Node Command Description enable show syslog The command displays all log messages recorded in the switch. enable show syslog level LEVEL This command displays the log messages with the “LEVEL”...
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 30.8 /Serie 852 (ETH ERNET-Zubehör)/Anhang/MODBU S-T abellen 852- x30x @ 27\mod_1466762389292_21.doc x @ 214678 @ 233 @ 1 10.4 MODBUS/TCP Tables 10.4.1 Data Format and Function Code MODBUS TCP supports different types of data formats for reading. The most...
Page 295
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type 0x0050 12 words ASCII Firmware Version=” 8528-000-1.1.0.b1” Word 0 Hi byte = ‘8’ Word 0 Lo byte = ‘5’ Word 1 Hi byte = ‘2’...
Page 296
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type Port Information 0x0100 to 1 word Port 1 to 10 Link Status 0x0109 0x0000: Link down 0x0001: 10M-Full-FC_ON (FC: Flow Control) 0x0002: 10M-Full-FC_OFF 0x0003: 10M-Half-FC_ON...
Page 297
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type Redundancy & Ring Information 0x0500 2 word Spanning Tree Status 0x0000: none 0x0001: STP 0x0002: RSTP 0x0003: MSTP 0x0501 1 word Xpress-ring Status 0x0000: Disabled...
Page 298
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type 0x0520 2 word Xpress-ring Current status for Ring 1 Ring 1 – Primary Port 0x0000: No connection 0x0001: Forwarding 0x0002: Blocking 0x0521 Ring 1 – Secondary Port...
Page 299
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type 0x0630 to 1 word Ring Port: 0x064F 0x0000: No 0x0001: Yes Dual-Ring Information 0x0700 1 word Dual- Ring State: 0x0000: Disabled. 0x0001: Enabled. 0x0701...
Page 300
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type 0x070b 1 word Bridge Role for Sub-Ring: 0x0000: Learning. 0x0001: Master. 0x0002: Arbiter. 0x0003: Forwarder. 0x0004: Pre-Forwarder. 0x070c 2 Word Sub-ring Current status for Dual-Ring Subport-1 –...
Page 301
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type 0x0825 1 word Control VLAN of Ring E:0x000b Control VLAN=11 0x0826 1 word Right Port of Ring High byte –Port No. Low byte – Port Type.
Page 302
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type 0x087b 1 word Ring ID for ERPSn (n=4) 0x087c 1 word State for ring of ERPS 0x087d 33 words Name of Ring 0x089e 1 word Version &...
Page 303
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type 0x0904 1 word Port 1 status High byte –Port No. Low byte –Port Status. b’0:1 Type 00: Bound(STP) 01: Bound(RSTP) 10: Bound(MSTP) 11: Internal(MSTP) b’2 P2P...
Page 304
Appendix WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type 0x0ac0 1 word Instance ID (Fixed 0x0e, 14) 0x0ae0 1 word Instance ID (Fixed 0x0f, 15) 0x0b00 1 word Instance ID (Fixed 0x10, 16)
Page 305
WAGO-ETHERNET-Zubehör 852 Appendix 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Table 161: MODBUS Registers Register Data Rep. Description Address Type 0x1000 1 word Instance ID (Fixed 0x38, 56) 0x1020 1 word Instance ID (Fixed 0x39, 57) 0x1040 1 word Instance ID (Fixed 0x3a, 58)
Page 306
List of Figures WAGO-ETHERNET-Zubehör 852 852-1305 8/4-Port 100BASE-T/1000BASE-SX/LX Pos : 32 /D okumentation allgemei n/Verz eic hniss e/Abbil dungs verz eic hnis - Übersc hrift oG und Verz eichnis @ 3\mod_1219222916765_21.doc x @ 21080 @ @ 1 List of Figures Figure 1: Front View of the Industrial Managed Switch ........