WAGO 852 Series Manual
8 ports 100base-tx, 2 slots 100base-fx industrial switch
Hide thumbs
Also See for 852 Series:
- Assembly, installation and handling (28 pages) ,
- Operating and assembly instructions (2 pages) ,
- Manual (36 pages)
Subscribe to Our Youtube Channel
Related Manuals for WAGO 852 Series
Summary of Contents for WAGO 852 Series
- Page 1 Manual WAGO ETHERNET Accessories 852 852-103 Industrial Switch 8 Ports 100BASE-TX; 2 Slots 100BASE-FX Version 1.0.3...
- Page 2 We wish to point out that the software and hardware terms as well as the trademarks of companies used and/or mentioned in the present manual are generally protected by trademark or patent. WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH. Manual Version 1.0.3...
-
Page 3: Table Of Contents
WAGO ETHERNET Accessories 852 Table of Contents 852-103 Industrial Switch Table of Contents Notes about this Documentation ............. 5 Validity of this Documentation..............5 Copyright ....................5 Symbols ....................6 Number Notation ..................8 Font Conventions ................... 8 Important Notes ..................9 Legal Bases .................... - Page 4 Table of Contents WAGO ETHERNET Accessories 852 852-103 Industrial Switch Installation .................... 30 Installation on a Carrier Rail..............30 Removal from Carrier ail ............... 30 Connect Devices ..................31 Power Supply ..................31 External Alarm Contact Connection ............32 Appendix....................33 RJ-45 Cables ..................
-
Page 5: Notes About This Documentation
Manual by third parties that violate pertinent copyright provisions is prohibited. Reproduction, translation, electronic and phototechnical filing/archiving (e.g., photocopying) as well as any amendments require the written consent of WAGO Kontakttechnik GmbH & Co. KG, Minden, Germany. Non-observance will involve the right to assert damage claims. Manual... -
Page 6: Symbols
Notes about this Documentation WAGO ETHERNET Accessories 852 852-103 Industrial Switch Symbols Personal Injury! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury. Personal Injury Caused by Electric Current! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury. - Page 7 WAGO ETHERNET Accessories 852 Notes about this Documentation 852-103 Industrial Switch Additional Information: Refers to additional information which is not an integral part of this documentation (e.g., the Internet). Manual Version 1.0.3...
-
Page 8: Number Notation
Notes about this Documentation WAGO ETHERNET Accessories 852 852-103 Industrial Switch Number Notation Table 1: Number Notation Number Code Example Note Decimal Normal notation Hexadecimal 0x64 C notation Binary '100' In quotation marks, nibble separated '0110.0100' with dots (.) Font Conventions... -
Page 9: Important Notes
2.1.1 Subject to Changes WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from the granting of patents or from the legal protection of utility patents. -
Page 10: Technical Condition Of Specified Devices
These modules contain no parts that can be serviced or repaired by the user. The following actions will result in the exclusion of liability on the part of WAGO Kontakttechnik GmbH & Co. KG: •... -
Page 11: Safety Advice (Precautions)
Only install in appropriate housings, cabinets or electrical operation rooms! WAGO's 852 Series ETHERNET Switches are considered exposed operating components. Therefore, only install these switches in lockable housings, cabinets or electrical operation rooms. Access must be limited to authorized, qualified staff having the appropriate key or tool. - Page 12 Important Notes WAGO ETHERNET Accessories 852 852-103 Industrial Switch Protect the components against materials having seeping and insulating properties! The components are not resistant to materials having seeping and insulating properties such as: aerosols, silicones and triglycerides (found in some hand creams).
-
Page 13: Special Use Conditions For Ethernet Devices
Please note the following when using ETHERNET devices in your system: • Do not connect control components and control networks directly to an open network such as the Internet or an office network. WAGO recommends putting control components and control networks behind a firewall. •... -
Page 14: General
Protective caps for unused ports Industrial ETHERNET Technology The line of switches from WAGO ensure the scalability of your network infrastructure with outstanding electrical and mechanical characteristics. These robust devices are designed for industrial use and they are fully compliant with IEEE 802.3, 802.3u. -
Page 15: Autonegotiation
WAGO ETHERNET Accessories 852 General 852-103 Industrial Switch Autonegotiation Autonegotiation allows the switch to detect the transmission rate and operating mode for each port and the connected subscriber or subscribers, and to set them automatically. The highest possible mode (transmission speed and operating mode) is set. -
Page 16: Device Description
Device Description WAGO ETHERNET Accessories 852 852-103 Industrial Switch Device Description The 852-103 Industrial Switch is an 8-port 10/100BASE-TX with dual SFP 100Base-FX port (SFP modules are optional) ETHERNET switch. The switch has a rugged housing, a redundant power supply and function monitoring with relay, making it ideal for a wide range of applications. -
Page 17: View
WAGO ETHERNET Accessories 852 Device Description 852-103 Industrial Switch View 4.1.1 Front View Figure 1: Front View of the Industrial Switch Table 3: Legend for Figure “Front View of the Industrial Switch” Descrip- Pos. Meaning Details see Section tion “Device Description” >... -
Page 18: Top View
Device Description WAGO ETHERNET Accessories 852 852-103 Industrial Switch Table 3: Legend for Figure “Front View of the Industrial Switch” Descrip- Pos. Meaning Details see Section tion Status LED 100 Mbit/s for fiber optic port, port “Device Description” > OFFLINE offline (2) “Display Elements”... -
Page 19: Connectors
WAGO ETHERNET Accessories 852 Device Description 852-103 Industrial Switch Connectors 4.2.1 Grounding screw The switch must be grounded. Connect the grounding screw to the ground potential. Do not operate the switch without an appropriately installed protective earth conductor. Figure 3: Grounding screw 4.2.2... - Page 20 Device Description WAGO ETHERNET Accessories 852 852-103 Industrial Switch Warning of damage to equipment by electrostatic discharge DC Powered Switch: Power is supplied through an external DC power source. Since the switch does not include a power switch, plugging its power adapter into a power outlet will immediately power it on.
-
Page 21: Network Connection
WAGO ETHERNET Accessories 852 Device Description 852-103 Industrial Switch 4.2.3 Network Connection The industrial switch uses ports with fiber optic or copper connectors that can be used with ETHERNET and/or Fast ETHERNET protocols. Figure 5: Network Connection Table 6: Legend for Figure „Network Connection“... -
Page 22: 10/100Base-Tx Ports
Device Description WAGO ETHERNET Accessories 852 852-103 Industrial Switch 4.2.3.2 10/100BASE-TX Ports The 10/100BASE-TX ports support network speeds of either 10 Mbit/s or 100 Mbit/s, and can operate in half- and full-duplex transfer modes. The ports also offer automatic MDI/MDI-X crossover detection that gives true “plug and play”... -
Page 23: Display Elements
WAGO ETHERNET Accessories 852 Device Description 852-103 Industrial Switch Display Elements The industrial switch is equipped with device LEDs and port LEDs. You can see the status of the switch at a quick glance of the device LEDs, while the port LEDs provide information about connection actions. -
Page 24: Port Leds
Device Description WAGO ETHERNET Accessories 852 852-103 Industrial Switch 4.3.2 Port LEDs Figure 7: Port LEDs Table 8: Legend for Figure “Port LEDs” Name Status Description 10/100Base-TX Port in operation at 100 Mbit/s. Green Ports LED (1 LED for each Port in operation at 10 Mbit/s. -
Page 25: Operating Elements
WAGO ETHERNET Accessories 852 Device Description 852-103 Industrial Switch Operating Elements 4.4.1 DIP Switches On the top side of the Industrial Switch there are DIP switches to configure the alarm and arbiter configurations. The meaning of the DIP switch settings are described below: Figure 8: DIP Switches Table 9: Legend for Figure “DIP Switches”... - Page 26 Device Description WAGO ETHERNET Accessories 852 852-103 Industrial Switch DIP-switches let the user manually turn “ON/OFF” any port, the external Alarm, or the redundant power supply. DIP-switch to the “ON” position to manually enable the alarm function for the port.
-
Page 27: Technical Data
WAGO ETHERNET Accessories 852 Device Description 852-103 Industrial Switch Technical Data 4.5.1 Device Data Table 10: Technical Data – Device Data Width Carrier rail mounting 50 mm Height Carrier rail mounting 120 mm (from the top edge of the carrier rail) -
Page 28: Environmental Conditions
Device Description WAGO ETHERNET Accessories 852 852-103 Industrial Switch 4.5.5 Environmental Conditions Table 14: Technical Data ‒ Environmental Conditions Surrounding air temperature, operation -40 … +70 °C max. +60 °C (UL) Surrounding air temperature, storage -40 … +85 °C Relative humidity (without 5 …... -
Page 29: Approvals
WAGO ETHERNET Accessories 852 Device Description 852-103 Industrial Switch Approvals The following approvals have been granted for the WAGO ETHERNET accessory product “Industrial Switch” (852-103): Conformity Marking UL508 (E175199) Manual Version 1.0.3... -
Page 30: Mounting
Mounting WAGO ETHERNET Accessories 852 852-103 Industrial Switch Mounting Installation The location selected to install the Industrial Switch may greatly affect its performance. When selecting a site, we recommend considering the following rules: • Install the Industrial Switch at an appropriate place. See in chapter “Technical Data”... -
Page 31: Connect Devices
WAGO ETHERNET Accessories 852 Connect Devices 852-103 Industrial Switch Connect Devices Power Supply The industrial switch uses direct current power supply for 12 … 60 V. The primary and secondary network link is established via a 6-pin plug-in connection located on the top of the industrial switch. -
Page 32: External Alarm Contact Connection
Connect Devices WAGO ETHERNET Accessories 852 852-103 Industrial Switch External Alarm Contact Connection The Industrial Switch has one alarm contact connection point located on the grey terminal block on the top panel. For detailed instructions on how to connect the... -
Page 33: Appendix
WAGO ETHERNET Accessories 852 Appendix 852-103 Industrial Switch Appendix RJ-45 Cables Always use category 5e cables to connect your network devices. The pin assignment is given below: Table 15: RJ-45 Cable Contact Description Pair Color (acc. 4-wire 8-wire EIA/TIA 568B) -
Page 34: List Of Figures
List of Figures WAGO ETHERNET Accessories 852 852-103 Industrial Switch List of Figures Figure 1: Front View of the Industrial Switch............17 Figure 2: Top View of the Industrial Switch ............18 Figure 3: Grounding screw .................19 Abbildung 4: Power Supply (PWR/RPS) .............19 Figure 5: Network Connection ................21... -
Page 35: List Of Tables
WAGO ETHERNET Accessories 852 List of Tables 852-103 Industrial Switch List of Tables Table 1: Number Notation ..................8 Table 2: Font Conventions ...................8 Table 3: Legend for Figure “Front View of the Industrial Switch”......17 Table 4: Legend for Figure “Top View of the Industrial Switch” ......18 Table 5: Legend for Figure “Power Supply (PWR/RPS)”... - Page 36 WAGO Kontakttechnik GmbH & Co. KG Postfach 2880 • D - 32385 Minden Hansastraße 27 • D - 32423 Minden Phone: +49 571 887 – 0 Fax: +49 571 887 – 844169 E-Mail: info@wago.com Internet: www.wago.com...
Need help?
Do you have a question about the 852 Series and is the answer not in the manual?
Questions and answers