R&S SMW-K44 User Manual page 265

Satellite Navigation
Manual operation:
[:SOURce<hw>]:BB:GNSS:SVID<ch>:SBAS:SIGNal:L1Band:CA:POWer:OFFset
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GALileo:SIGNal:L1Band:E1OS:POWer:
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GLONass:SIGNal:L2Band:CA:POWer:
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GLONass:SIGNal:L1Band:CA:POWer:
[:SOURce<hw>]:BB:GNSS:SVID<ch>:QZSS:SIGNal:L1Band:CA:POWer:OFFset
[:SOURce<hw>]:BB:GNSS:SVID<ch>:BEIDou:SIGNal:L2Band:B2I:POWer:OFFset
[:SOURce<hw>]:BB:GNSS:SVID<ch>:BEIDou:SIGNal:L1Band:B1I:POWer:OFFset
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GPS:SIGNal:L2Band:L2C:POWer:OFFset
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GPS:SIGNal:L2Band:CA:POWer:OFFset
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GPS:SIGNal:L2Band:P:POWer:OFFset
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GPS:SIGNal:L1Band:P:POWer:OFFset
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GPS:SIGNal:L1Band:CA:POWer:OFFset
Sets a power offset for the selected signal.
Parameters:
<PowerOffset>
Example:
Manual operation:
[:SOURce<hw>]:BB:GNSS:SVID<ch>:SBAS:POWer:COPY:SVID <Svid>
[:SOURce<hw>]:BB:GNSS:SVID<ch>:QZSS:POWer:COPY:SVID <Svid>
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GALileo:POWer:COPY:SVID <Svid>
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GLONass:POWer:COPY:SVID <Svid>
[:SOURce<hw>]:BB:GNSS:SVID<ch>:BEIDou:POWer:COPY:SVID <Svid>
[:SOURce<hw>]:BB:GNSS:SVID<ch>:GPS:POWer:COPY:SVID <Svid>
Sets the SV ID to that the configuration form the current satellite (SVID<ch>) is
applied.
Both SV IDs belong to the same GNSS system.
User Manual 1178.6379.02 ─ 01
See "Power Offset"
<PowerOffset>
OFFset <PowerOffset>
OFFset <PowerOffset>
OFFset <PowerOffset>
<PowerOffset>
<PowerOffset>
<PowerOffset>
<PowerOffset>
<PowerOffset>
<PowerOffset>
<PowerOffset>
<PowerOffset>
float
Range:
Increment: 0.01
*RST:
See Example "Configuring the SV power and modulation control
settings"
See "Signal Power Offset"
Signals and Power Configuration per Satellite
on page 59
-6 to 0
0
on page 259.
on page 66
Remote-Control Commands
265