Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual page 2004

ip route-map route-map-name [sequence-number number] match ipv6-interface interface-
name
no ip route-map route-map-name [sequence-number number] match ipv6-interface interface-
name
ip route-map route-map-name [sequence-number number] match metric metric [deviation
deviation]
no ip route-map route-map-name [sequence-number number] match metric metric
[deviation deviation]
ip route-map route-map-name [sequence-number number] set metric metric
[effect {add | subtract | replace | none}]
no ip route-map route-map-name [sequence-number number] set metric metric
[effect {add | subtract | replace | none}]
ip route-map route-map-name [sequence-number number] set tag tag-number
no ip route-map route-map-name [sequence-number number] set tag tag-number
ip route-map route-map-name [sequence-number number] set ip-nexthop ip_address
no ip route-map route-map-name [sequence-number number] set ip-nexthop ip_address
ip route-map route-map-name [sequence-number number] set ipv6-nexthop ipv6_address
no ip route-map route-map-name [sequence-number number] set ipv6-nexthop ipv6_address
arp ip_address hardware_address [alias]
no arp ip_address [alias]
clear arp-cache
ip dos arp-poison restricted-address ip_address
no ip dos arp-poison restricted-address ip_address
arp filter ip_address [mask ip_mask] [vid] [sender | target] [allow | block]
no arp filter ip_address
clear arp-cache
icmp type type code code {{enable | disable} | min-pkt-gap gap}
icmp unreachable [net-unreachable | host-unreachable | protocol-unreachable |
port-unreachable] {{enable | disable} | min-pkt-gap gap}
icmp echo [request | reply] {{enable | disable} | min-pkt-gap gap}
icmp timestamp [request | reply] {{enable | disable} | min-pkt-gap gap}
icmp add-mask [request | reply] {{enable | disable} | min-pkt-gap gap}
icmp messages {enable | disable}
ip dos scan close-port-penalty penalty_value
ip dos scan tcp open-port-penalty penalty_value
ip dos scan udp open-port-penalty penalty_value
ip dos scan threshold threshold_value
ip dos trap {enable | disable}
ip dos scan decay decay_value
show ip traffic
show ip interface [name | vlan vlan id]
show ip route [summary]
show ip route-pref
show ipv6 redist [rip]
OmniSwitch 6250 CLI Reference Guide November 2009
show ip access-list [access-list-name]
show ip route-map [route-map-name]
show ip router database [protocol type | gateway ip_address | dest {ip_address/prefixLen |
ip_address}]
show ip config
show ip protocols
show ip service
show arp [ip_address | hardware_address]
show arp filter [ip_address]
show icmp control
show icmp [statistics]
show tcp statistics
show tcp ports
show udp statistics
show udp ports
show ip dos config
show ip dos statistics
show ip dos arp-poison
IPv6 Commands
ipv6 interface if_name vlan vid [enable | disable]
[base-reachable-time time]
[ra-send {yes | no}]
[ra-max-interval interval]
[ra-managed-config-flag {true | false}]
[ra-other-config-flag {true | false}]
[ra-reachable-time time]
[ra-retrans-timer time]
[ra-default-lifetime time | no ra-default-lifetime]
[ra-send-mtu] {yes | no}
no ipv6 interface if_name
ipv6 address ipv6_address /prefix_length [anycast]
no ipv6 address ipv6_address [anycast]
ipv6 address ipv6_prefix eui-64
no ipv6 address ipv6_prefix eui-64
ipv6 dad-check ipv6_address if_name
ipv6 hop-limit value
no ipv6 hop-limit
ipv6 pmtu-lifetime time
ipv6 host name ipv6_address
no ipv6 host name ipv6_address
ipv6 neighbor stale-lifetime stale-lifetime
ipv6 neighbor ipv6_address hardware_address
page 10
{
if_name | loopback
{ | }
if_name loopback
{ }
if_name | loopback
{ }
if_name | loopback
{ }
if_name slot/port
}
IPv6 Commands