Alcatel-Lucent OmniSwitch 6250 Cli Reference Manual page 2003

efm-oam [ ] keepalive-interval
port slot/port -port2
efm-oam port slot/port[-port2] hello-interval seconds
efm-oam port slot/port[-port2] remote-loopback {process | ignore}
efm-oam port slot/port remote-loopback {start | stop}
efm-oam port slot/port[-port2] propagate-events {critical-event | dying-gasp} {enable |
disable}
efm-oam port slot/port[-port2] errored-frame-period [threshold threshold_symbols] [window
window_frames] [notify {enable | disable}]
efm-oam port slot/port[-port2] errored-frame [threshold threshold_symbols] [window
window_seconds] [notify {enable | disable}]
efm-oam port slot/port[-port2] errored-frame-seconds-summary [threshold
threshold_seconds] [window window_seconds] [notify {enable | disable}]
efm-oam multiple-pdu-count count
efm-oam port slot/port l1-ping [num-frames number] [delay milliseconds] [start]
show efm-oam configuration
show efm-oam port [slot/port1-port2] [enable | disable] [active | passive]
show efm-oam port slot/port detail
port
show efm-oam slot/port[-port2] statistics
port
show efm-oam statistics
show efm-oam port slot/port remote detail
show efm-oam port slot/port history [log-type { link-fault | errored-frame | errored-frame-
period | errored-frame-seconds | dying-gasp | critical } ]
show efm-oam port slot/port l1-ping detail
/
clear efm-oam statistics port slot port[-port2]
clear efm-oam log-history port slot/port[-port2]
UDLD Commands
udld {enable | disable}
]
udld port slot/port[-port2 {enable | disable}
[ ]]
udld port slot/port[-port2 mode {normal | aggressive}
[ ]]
udld port slot/port[-port2 probe-timer seconds
[ ]]
no udld port slot/port[-port2 probe-timer
[ ]]
udld port slot/port[-port2 echo-wait-timer seconds
[ ]]
no udld port slot/port[-port2 echo-wait-timer
clear udld statistics [port slot/port]
show udld configuration
show udld configuration port [slot/port
show udld statistics port slot/port
show udld neighbor port slot/port
]
show udld status port [slot/port
OmniSwitch 6250 CLI Reference Guide
seconds
]
November 2009
Port Mapping Commands
port mapping port_mapping_sessionid {enable | disable}
no port mapping port_mapping_sessionid
show port mapping [port_mapping_sessionid]
IP Commands
ip interface name [address ip_address] [mask subnet_mask] [admin [enable | disable]] [vlan
vid] [forward | no forward] [local-proxy-arp | no local-proxy-arp] [eth2 | snap] [primary
| no primary]
no ip interface name
ip router primary-address ip_address
ip router router-id ip_address
ip static-route ip_address [mask mask] gateway gateway [metric metric]
no ip static-route ip_address [mask mask] gateway ip_address [metric metric]
ip route-pref {static | rip | ebgp | ibgp} value
ip default-ttl hops
ping {ip_address | hostname} [count count] [size packet_size] [interval seconds] [timeout
seconds]
traceroute {ip_address | hostname} [max-hop max_hop_count]
ip directed-broadcast {on | off}
ip service {all | service_name | port service_port}
no ip service {all | service_name | port service_port}
ip redist {local | static | rip} into {rip} route-map route-map-name [status {enable | disable}]
no ip redist {local | static | rip} into {rip} [route-map route-map-name]
ip access-list access-list-name
no ip access-list access-list-name
ip access-list access-list-name
[redist-control {all-subnets | no-subnets | aggregate}]
no ip access-list access-list-name
ip route-map route-map-name [sequence-number number] match ip-nexthop
{access-list-name | ip_address/prefixLen
no ip route-map route-map-name [sequence-number number] match ip-nexthop
{access-list-name | ip_address/prefixLen
ip route-map route-map-name [sequence-number number] match ipv6-nexthop
{access-list-name | ipv6_address/prefixLen [permit | deny]}
no ip route-map route-map-name [sequence-number number] match ipv6-nexthop
{access-list-name | ipv6_address/prefixLen [permit | deny]}
ip route-map route-map-name [sequence-number number] match ipv4-interface interface-
name
no ip route-map route-map-name [sequence-number number] match ipv4-interface interface-
name
page 9
address [action {permit | deny}]
address/prefixLen
address
address/prefixLen
[permit | deny]}
[permit | deny]}
UDLD Commands