JR ProPo DSX11 Operation Manual page 66

Method of using the Function Mode Functions (Glider)
Dual Rate & EXPonential
Channel Display
AILE
Aileron
ELEV
Elevator
RUDD
Rudder
Dual Rate Position
This function carries out setting of the rate (tilt) of each of
the aileron, elevator, and rudder channels.
For each channel and position, adjustment is possible over
the ranges of the Dual Rate amount (0 to 125%), and
Exponential (0: LIN to ±125%).
Exponential is a function that sets the movement around
the neutral position to "mild" (plus direction) or "quick"
(minus direction) without changing the maximum control
surface angle, by linking the servo movement correspond-
ing to the stick operation in a logarithmic curve. Further, the
settings can be understood visually using the graph
display.
Changeover Operation
For the position changeover, it is possible to carry out
independent changeover of each of the aileron, elevator,
and rudder control surfaces (Position 0 and 1 (The rudder
switch can be set up to Position 2)) using the lever
switches, and to carry out changeover setting (Positions 0,
1, 2, and 3) through linking with the Flight Mode.
Auto Dual Rate & Exponential
In the setting screen, by rotating the dial to move the cursor,
the screen will change as shown below, and it will be
possible to select the switch or position corresponding to
each Flight Mode as shown in the figure to the right. Rotat-
ing the dial to move the cursor on top of the graph will cause
the Auto Setting part to be displayed, allowing the linkage
settings to be determined.
Make the selection using the switches, or select the position
number that you wish to allocate. Further, the preset condi-
tion can be set using the key that is located to the left of
the screen.
Setting Method
In the setting screen, by rotating the dial to move the cursor,
the screen will change as shown above, and it will be
possible to select the switch or position corresponding to
each Flight Mode as shown in the figure to the right.
Make the selection using the switches, or select the
position number or switch that you wish to allocate.
Further, the preset condition can be set using the
located at the left of the screen.
Current Transmitter Condition (Set to the Pos0 side)
Dual Rate Amount Exponential Amount
(0 to 125%) (LIN=0 to ±100%)
For each Flight Mode, select whether to change over the value
of position 0 or 1 (or 2) using the switches, or to set the value
of position 0 to 3. In the situation where the switches are
selected (initial setting), each of the D/R switch conditions
(Position 0 or 1 (or 2)) will become the Dual Rate amount.
In the Auto Dual Rate function, it will be possible to use the
Flight Mode switches to link to the Flight Modes and change
between Dual Rate and Exponential.
key
Changeover Switch Selection
Selection is possible from the AILE, ELEV,
RUDD, or FMOD switches.
Setting Method
Match the cursor with the channel display part, and select the
channel that you wish to set from the list that is displayed.
Next, select each item of the position that you wish to set, and
rotate the dial to change the numerical values and implement
the settings.
When the stick of the corresponding channel is located in the
center, the items above and below will be selected simultane-
ously, and it will be possible to change each of the values in a
single operation. In the situation where you only wish to adjust
the value on one side, tilting the stick to the side will allow
adjustment of the cursor item which be automatically selected
when the stick is tilted.
In addition, the key will be enabled during adjustment of
the setting values to allow the Clear operation to take place. By
pressing the key, it will be possible to return the Dual Rate
(D/R) adjustment to 100% and the Exponential (EXP) adjust-
ment to LIN (0%).
Pressing the dial in this Rotating the dial will
condition will change to increase or
the Numerical Value decrease the values
Setting condition shown on both the +/-
at right. sides.
Auto Setting
*Note: In the situation where the Flight Mode
Name function has been used to change
the name, the display will be different.
Switch Changeover
Setting
Graph Display
Tilting the stick
will allow
adjustment on
only one side.
Item Selection Condition