Travel Adj - JR ProPo DSX11 Operation Manual

TRAVEL ADJust
This function is the right and left control surface angle
adjustment of the servo operation for each channel (taking
neutral as the reference). For each of the channels, adjust-
ment is possible over a range of 0 to 150% right and left.
The reference value is 100%, which is the normal control
surface angle.
Setting Method
First, determine the channel that you wish to set. By rotating
the dial to highlight the channel display part and pressing
the dial, the channel will become enclosed by a border.
Rotating the dial in this situation will allow increasing and
decreasing of the control surface angle amounts.
Tilt the stick or set the switch (SW) of the corresponding
channel to the side that you wish to adjust, and carry out the
adjustment.
After the numerical values have been determined, press the
dial again. This will return to the Channel Selection condi-
tion.
During adjustment of the control surface angle amounts, the
key will be enabled.
When the key is pressed, the displayed control surface
angle amounts will return to their original setting of 100%.
LIMIT ADJust
This function is the maximum control surface angle limiting
function of the servo operation for each channel (taking
neutral as the reference). It is possible to apply limits to the
maximum operation amount after the mixing of each
channel, and adjustment can be carried out over a range of
0 to 150% to the right and left for each channel. The
maximum control surface angle reference value is 150%.
Setting Method
First, determine the channel that you wish to set. By
rotating the dial to highlight the channel display part and
pressing the dial, the channel will become enclosed by a
border. Rotating the dial in this situation will increase or
decrease the control surface angle amount.
Tilt the stick or set the switch of the corresponding channel
to the side that you wish to adjust, and carry out the adjust-
ment.
After determining the numerical values, press the dial
again. This will return to the Channel Selection condition.
By pressing the key while adjusting the control surface
angle amounts, the displayed control surface amounts will
return to the initial setting of 150%.
*This function will operate with priority over all other
functions.
Channels that are being set:
THROThrottle
LTALLeft tail
AILE Aileron
RTAL Right tail
ELEVElevator
RTHR Right throttle
RUDD Rudder
LTHR Left throttle
GEAR Gear (Retractable
RELERight elevator
landing gear)
LELE Left elevator
FLAP Flaps
RRUD Right rudder
AUX2Auxiliary (AUX2)
LRUD Left rudder
AUX3Auxiliary (AUX3)
RFLPRight flap
AUX4Auxiliary (AUX4)
LFLP Left flap
AUX5Auxiliary (AUX5)
RAL1 Right aileron 1
AUX6Auxiliary (AUX6)
LAL1 Left aileron 1
RAILRight aileron
RAL2 Right aileron 2
LAIL Left aileron
LAL2 Left aileron 2
LEVNLeft elevon
PIT. Pitch
REVN Right elevon
---- Setting invalid
Pressing the dial in this condition
will change to the Numerical Value
Setting condition shown below.
Rotating the dial will increase or
decrease the value (0 to 100%).
By tilting the stick, the value in the
tilted direction can be adjusted.
Channels that are being set:
THROThrottle
LTALLeft tail
AILE Aileron
RTAL Right tail
ELEVElevator
RTHR Right throttle
RUDD Rudder
LTHR Left throttle
GEAR Gear (Retractable
RELERight elevator
landing gear)
LELE Left elevator
FLAP Flaps
RRUD Right rudder
AUX2Auxiliary (AUX2)
LRUD Left rudder
AUX3Auxiliary (AUX3)
RFLPRight flap
AUX4Auxiliary (AUX4)
LFLP Left flap
AUX5Auxiliary (AUX5)
RAL1 Right aileron 1
AUX6Auxiliary (AUX6)
LAL1 Left aileron 1
RAILRight aileron
RAL2 Right aileron 2
LAIL Left aileron
LAL2 Left aileron 2
LEVNLeft elevon
PIT. Pitch
REVN Right elevon
---- Setting invalid
Pressing the dial in this condition
will change to the Numerical Value
Setting condition shown below
Rotating the dial will increase or
decrease the value between 0 and
150%.
By tilting the stick, the value in the
tilted direction can be adjusted.