Servo Speed - JR ProPo DSX11 Operation Manual

SERVO SPEED

This function allows the speed of the servo connected to
each channel to be changed (made slower).
Setting can be carried out linked to the operation direction
and each switch position for each channel, and it is possible
to select the time taken when the angle to be moved by the
servo is set to 60 degrees as NORM, 0.176, ... 15.0
seconds. In this situation, Normal (NORM) is the normal
operation speed, which will be the fastest speed for the
servos utilized. Because the maximum speed will depend
Switch Selection
Position Selection
Throttle Stick Selection
For changing between positions during the setting, rotate
the dial to highlight the "Pos" characters. Pressing the dial in
this situation will display the options as shown in the figure
below to allow selection, so use the dial to select the position
that you wish to set. Pressing the dial once again will return
to the Item Selection condition.
Press the dial.
Setting Method
By rotating the dial to highlight each of the operation
direction parts of the channel that you wish to set, then
pressing the dial, the part will become enclosed by a
border. In this situation, rotate the dial to change the setting
amount.
Pressing the dial once again will return to the Selection
condition. Further, by pressing the
the setting amount, it will be possible to return the setting
amount to "NORM".
Although it is possible to carry out the settings for each
position, in order that either of the settings can always be
enabled, normally the Pos0 side is set to NORM to allow
the Pos1 value to be determined by changing the switch
operation.
Item Selection Condition
Press the dial.
Numerical Value Setting
Condition
(NORM, 0.176, 0.179, ... 15.0)
Current Transmitter Condition
key while adjusting
It is possible to set optional throttle stick positions as the
changeover points for each setting. For example, if 50 is
set, raising the stick from the center will change to the Pos0
value, and lowering the stick will change to the Pos1 value.
The input of numerical values should be carried out by
moving the stick to the actual required position, then press-
ing the STO key.
Note that it will be possible to preset to INH (inhibited condi-
tion) using the
on the servos that are utilized, refer to the rating of the
servo that you are utilizing. For example, when using a
servo with a rating of 0.2 sec/60°, the servo will operate at
a speed of 0.2 sec/60° even if the setting is "0.176". Be
sure to carefully confirm the actual servo operation
direction before carrying out the setting. Before setting this
item, first confirm whether or not the current positions of all
the servos should be fixed (HOLD).
Channels that are being set:
THROThrottle
AILE Aileron
ELEVElevator
RUDD Rudder
GEAR Gear (Retractable
landing gear)
FLAP Flaps
AUX2Auxiliary (AUX2)
AUX3Auxiliary (AUX3)
AUX4Auxiliary (AUX4)
AUX5Auxiliary (AUX5)
AUX6Auxiliary (AUX6)
RAILRight aileron
LAIL Left aileron
LEVNLeft elevon
REVN Right elevon
Operation Switch Selection Method
By rotating the dial to highlight "SW SEL" and pressing
the dial, the Switch Selection Screen described below
will be displayed, allowing selection of the Switch that
you wish to set.
Note: It will only be possible to set SPS if the SPS
function has been set.
Throttle Stick Linkage Setting
key.
LTALLeft tail
RTAL Right tail
RTHR Right throttle
LTHR Left throttle
RELERight elevator
LELE Left elevator
RRUD Right rudder
LRUD Left rudder
RFLPRight flap
LFLP Left flap
RAL1 Right aileron 1
LAL1 Left aileron 1
RAL2 Right aileron 2
LAL2 Left aileron 2
PIT. Pitch
---- Setting invalid