Aile → Rudd - JR ProPo DSX11 Operation Manual

AILE→RUDD mix
This mixing enables a smooth start to turns by using mixing
to the rudder following aileron operation.
Mixing Amount (±125%)
Aileron Operation Direction
L: Left Side, R: Right Side
Linkage Position Setting (INH, 0 to 100)
Setting Method
First, determine the right side or the left side of the position that
you wish to set. By rotating the dial to highlight the display part,
then pressing the dial, this part will become enclosed by a
border. Rotating the dial in this condition will allow increasing
and decreasing of the mixing amount.
Once the numerical values have been determined, press the
dial once again. This returns to the Selection condition.
In the Numerical Value Setting condition, the
enabled.
By pressing the key, the mixing amount will return to zero.
This mixing takes two values, and is always operating.
Normally, the Pos0 side is set to 0% and the Pos1 value is
determined to apply mixing using special switch operation. It
may be convenient to use this when you also wish to apply
mixing while Pos0 is in the normal condition.
AILE→FLAP MIX
This mixing makes rolling easier by using flaps as ailerons
by mixing to the flaps following aileron operation.
In the situation where you wish to reverse the mixing
direction, increase the mixing amount in the minus direction.
In order to use this mixing, Dual Flap setting will be neces-
Mixing Amount (±125%)
Aileron Operation Direction
L: Left Side, R: Right Side
Switch Selection
Linkage Position Setting (INH, 0 to 100)
Setting Method
First, determine the left side or the right side of the position
that you wish to set. By rotating the dial to highlight the
display part, then pressing the dial, this part will become
enclosed by a border. Rotating the dial in this condition will
allow increasing and decreasing of the mixing amount.
Once the numerical values have been determined, press
the dial once again. This returns to the Selection condition.
In the Numerical Value Setting condition, the
be enabled.
By pressing the key, the mixing amount will return to
zero.
This mixing takes two values, and is always operating.
Normally, the Pos0 side is set to 0% and the Pos1 value is
determined to apply mixing using special switch operation.
It should become more easily understandable to use this
when you also wish to apply mixing while Pos0 is in the
normal condition.
In the situation where you wish to reverse the mixing
direction, increase the mixing amount in the minus
direction.
Current Transmitter Condition (Set to Pos0)
Switch Selection
Operation Switch Selection Method
For the lever switch that sets the mixing function ON and
OFF, by rotating the dial to highlight "SW SEL" and then
pressing the dial it is possible to carry out switch selection.
For the setting method, refer to the items in section
Servo Speed.
Throttle Stick Linkage Setting
key will be
It is possible to set the mixing changeover point to an
optional position on the throttle stick. For example, when
this point is set to 50, moving the stick up above the center
will take the Pos0 value, while moving the stick below the
center will become the Pos1 value.
Note that it is possible to set the preset to INH (inhibited
condition) using the
sary. Accordingly, set Dual Flap in the Wing Type (System
Setting mode). When this has been set, it will be possible to
select this item from the function list.
Current Transmitter
Condition (Set to Pos0)
Operation Switch Selection Method
The display of the lever switch that sets the mixing function
ON and OFF, and the position where the switch is ON is as
shown above. In the situation where the setting is ON,
decide which of the values to take.
For the setting method, refer to the items in
Throttle Stick Linkage Setting
key will
It is possible to set the mixing changeover point to an
optional position on the throttle stick. For example, when
this point is set to 50, moving the stick up above the center
will take the Pos0 value, while moving the stick below the
center will become the Pos1 value.
Note that it is possible to set the preset to INH (inhibited
condition) using the
key.
Servo Speed.
key.