Riso RZ3xx Series Technical Manual page 315

1. System Panel Test Mode
No. Sensors, switches
0001 Wakeup Key
0002 Solenoid counter connection signal
0003 24V A output signal
0004 24V B output signal
0005 Serviceman safety SW (Rear cover safety SW)
No. Motor solenoid system
0062 Wakeup LED
No. Unit check
Test Print A (checkered)
0080
Creates Test pattern 1 (Checker Flag)
Test Print B (cross stripes)
0081
Creates Test pattern 2 (Cross Lines)
Test Print C (Dot1) [Available only on RZ3 series]
0082
Creates Test pattern 4 (Dot 1 )
Test Print D (Dot2) [Available only on RZ3 series]
0083
Creates Test pattern 5 (Dot 2 )
Test Print E (Dot1 + Cross Lines) [Available only on RZ3 series]
0084
Creates Test pattern 6 (Dot 1 + Cross Lines)
Test Print F (Dot2 + cross stripes) [Available only on RZ3 series]
0085
Creates Test pattern 7 (Dot 2 + Cross Lines)
Paper-Feed Test (continuous feeding)
0087
Speed 1 = 60rpm
Low-Speed Printing Operation
0088
Prints continuously at 15 rpm.
Stepped Printing Operation
0089
Press "Start" key to switch on the suction fan. Prints at 15 rpm only while "Test print" key is pressed.
Printing stops when "Test Print" key is released, and resumes if the key is pressed again. Press "Stop" to switch suction fan off.
Unit Initialization
0094
Initializes the mechanical moving units to their home positions (TPH pressure, master compression plate, drum lock,
clamp unit, vertical print position, printing pressure).
System Configuration Data Output
0095
Creates a master for the CI system data.
Error Record
0099
Stores the error logs accumulated on FLASH memory into CF card.
Rev Manual Event Code Set
0100
Stores the settings set in Test mode "No. 196 to 198" manual event codes into REv Flash address in CF card.
Machine Clock activation
0101
(Available only on RZ3 series)
No. Data clear
Clearing Jam Status Data
0110
Forcibly clears the jam.
Clearing User Memory
0111
User area memory clear
(Memo down all the settings before activation.)
Clearing Normal Area Test-Mode Data Memory [MACHINE]
Normal area test mode memory clear for test modes
0112
on the machine.
(Memo down all the settings before activation.)
Maintenance Count Clear (master making)
0113
Maintenance Call master count clear
Maintenance Count Clear (printing)
0114
Maintenance Call copy count clear
Maintenance Count Clear (print drum)
0115
Maintenance Call print drum print count clear
Clearing Normal Area Test-Mode Data Memory [PRINT DRUM]
Normal area test mode memory clear for test modes
0117
on the print drum.
(Memo down all the settings before activation.)
RISO Inc. Technical Communications
Key Pressed
Solenoids counter connected
24V-A ON (24V output)
24V-B ON (24V output)
Short interval beep sound = SW ON (Rear Cover installed).
Long interval beep sound = SW OFF (Rear Cover removed: Interlock Safety Switch off).
LED Illuminates
Speed 2 = 80rpm Speed 3 = 100rpm
Activates time set by Test Modes No.0171 to 0173.
The new clock time set by test mode No. 0171 through No.0173 will not be
activated unless this test mode No. 0101 is activated.
This test mode can also be used to clear error data for items for which
jam can otherwise be cleared only by the jam release procedure.
Consumables errors cannot be cleared.
Initializes data in user area memory to the programming defaults.
Initializes all normal area test mode settings on the machine
to their programming default values.
The protected area test modes stay unchanged.
Clears the maintenance-call message for master making.
Clears the maintenance-call message for printing.
Clears the maintenance-call message for print drum.
Initializes all normal area test mode settings within the EEPROM of the print drum to
their programming default values. The protected area test modes stay unchanged.
Detection status
Remarks
Details
Speed 4 = 110rpm Speed 5 = 130rpm
Details
[ 17 - 3 ]
CHAPTER 17: TEST MODE
us.riso.com