Honda CBR650F Service Manual page 12

dummyhead dummyhead
COOLING SYSTEM SPECIFICATIONS
Coolant capacity
Radiator cap relief pressure
Thermostat
Recommended
antifreeze
LUBRICATION SYSTEM SPECIFICATIONS
Engine oil capacity
Recommended engine oil
Oil pressure at EOP switch
Oil pump rotor
CYLINDER HEAD/VALVES SPECIFICATIONS
Cylinder compression at 300 min
Valve clearance
Camshaft Cam lobe height
Oil clearance
Runout
Valve lifter Valve lifter O.D.
Valve lifter bore I.D.
Valve, valve Valve stem O.D.
guide
Valve guide I.D.
Stem-to-guide
clearance
Valve guide height
Valve seat width
Valve spring free length
Cylinder head warpage
ITEM
Radiator and engine
Reserve tank (Upper level)
Begin to open
Fully open
Valve lift
Except TH model
TH model
ITEM
At draining
At oil filter change
At disassembly
Tip clearance
Body clearance
Side clearance
ITEM
-1
(rpm)
IN
EX
IN
EX
IN
EX
IN/EX
IN
EX
IN/EX
IN/EX
SPECIFICATIONS
2.5 liters (2.6 US qt, 2.2 Imp qt)
0.21 liter (0.22 US qt, 0.18 Imp qt)
108 – 137 kPa (1.1 – 1.4 kgf/cm
80 – 84°C (176 – 183°F)
95°C (203°F)
8 mm (0.3 in) minimum
High quality ethylene glycol antifreeze containing silicate-free
corrosion inhibitors (Mix the distilled water and antifreeze in the
ratio of 1:1)
Honda PRE-MIX COOLANT or equivalent
STANDARD
2.6 liters (2.7 US qt, 2.3 Imp qt)
2.9 liters (3.1 US qt, 2.6 Imp qt)
3.5 liters (3.7 US qt, 3.1 Imp qt)
Honda "4-stroke motorcycle oil" or an
equivalent motor oil
API service classification: SG or higher
(except oils labeled as energy
conserving on the circular API service
label)
JASO T903 standard: MA
Viscosity: SAE 10W-30
2
490 kPa (5.0 kgf/cm , 71 psi)
-1
at 5000 min (rpm)/80°C (176°F)
0.15 (0.006)
0.15 – 0.21 (0.006 – 0.008)
0.02 – 0.09 (0.001 – 0.004)
STANDARD
2
1,500 kPa (15.3 kgf/cm , 218 psi)
0.20 ± 0.03 (0.008 ± 0.001)
0.28 ± 0.03 (0.011 ± 0.001)
34.5800 – 34.8200 (1.36141 – 1.37086)
34.3600 – 34.6000 (1.35275 – 1.36220)
0.020 – 0.062 (0.0008 – 0.0024)
–
25.978 – 25.993 (1.0228 – 1.0233)
26.010 – 26.026 (1.0240 – 1.0246)
4.475 – 4.490 (0.1762 – 0.1768)
4.465 – 4.480 (0.1758 – 0.1764)
4.500 – 4.512 (0.1772 – 0.1776)
0.010 – 0.037 (0.0004 – 0.0015)
0.020 – 0.047 (0.0008 – 0.0019)
12.70 – 13.00 (0.500 – 0.512)
0.90 – 1.10 (0.035 – 0.043)
38.94 (1.533)
–
GENERAL INFORMATION
2
, 16 – 20 psi)
Unit: mm (in)
SERVICE LIMIT
–
–
–
–
–
0.20 (0.008)
0.35 (0.014)
0.12 (0.005)
Unit: mm (in)
SERVICE LIMIT
–
–
–
34.56 (1.361)
34.34 (1.352)
0.10 (0.004)
0.04 (0.002)
25.97 (1.022)
26.04 (1.025)
4.465 (0.1758)
4.455 (0.1754)
4.54 (0.179)
0.075 (0.0030)
0.085 (0.0033)
–
1.5 (0.06)
37.8 (1.49)
0.10 (0.004)
1-7