Teledyne T101 Operation Manual page 19

Teledyne ML - T101 Operation Manual TABLE OF CONTENTS
LIST OF FIGURES
Figure 3-1. Front Panel Layout ......................................................................................... 27
Figure 3-2. Display Screen and Touch Control ..................................................................... 27
Figure 3-3. Display/Touch Control Screen Mapped to Menu Charts ......................................... 29
Figure 3-4. Rear Panel Layout .......................................................................................... 30
Figure 3-5. Internal Chassis Layout ................................................................................... 32
Figure 3-6. Analog In Connector ....................................................................................... 33
Figure 3-7. Analog Output Connector ................................................................................. 34
Figure 3-8. Current Loop Option Installed on the Motherboard ............................................... 35
Figure 3-9. Status Output Connector ................................................................................. 36
Figure 3-10. Control Input Connector ................................................................................ 38
Figure 3-11. Pneumatic Connections, Basic Configuration Using Gas Dilution Calibrator .............. 40
Figure 3-12. Pneumatic Connections, Basic Configuration Using Bottled Span Gas ..................... 41
Figure 3-13. Pneumatic Diagram of the T101 Standard Conf iguration ...................................... 42
Figure 3-14. Basic Pneumatic Connections for Units with Valve Options ................................... 45
Figure 3-15. Pneumatic Diagram of the T101 With Z/S Option Installed ................................... 46
Figure 3-16. Pneumatic Diagram of the T101 with IZS Options Installed .................................. 49
Figure 4-1. Viewing T101 TEST Functions ........................................................................... 60
Figure 4-2. Viewing and Clearing T101 WARNING Messages .................................................. 62
Figure 4-3. Analog Output Connectors Def ined .................................................................... 66
Figure 4-4. Setup for Calibrating Analog Outputs ................................................................. 91
Figure 4-5. Setup for Calibrating Current Outputs ................................................................ 93
Figure 4-6. DIAG - Analog Inputs (Option) Configuration Menu .............................................. 96
Figure 4-7. Rear Panel Connector Pin-Outs for RS-232 Mode................................................ 105
Figure 4-8. CPU Connector Pin-Outs for RS-232 Mode......................................................... 106
Figure 4-9. Jumper and Cables for Multidrop Mode ............................................................. 117
Figure 4-10.Multidrop PCA Host/Analyzer Interconnect Diagram ........................................... 118
Figure 4-11. Default DAS Channels Setup......................................................................... 129
Figure 4-12. APICOM User Interface for Configuring the DAS ............................................... 142
Figure 5-1. Status Output Connector ............................................................................... 144
Figure 5-2. Control Inputs with Local 5 V Power Supply ...................................................... 146
Figure 5-3.Control Inputs with External 5 V Power Supply ................................................... 146
Figure 5-4. APICOM Remote Control Program Interface....................................................... 154
Figure 6-1. Setup for Manual Calibration without Z/S Valve or IZS Option .............................. 166
Figure 6-2. Setup for Manual Calibration with Z/S Valve Option Installed ............................... 170
Figure 6-3. Setup for Manual Calibration Check with Z/S Valve or IZS Option ......................... 175
Figure 6-4. Typical Setup for Manual Calibratio in Multigas Measurement Mode ....................... 178
Figure 8-1. Sample Particulate Filter Assembly .................................................................. 202
Figure 8-2. Charcoal Canister Assembly ........................................................................... 205
Figure 8-3. H2S - SO2 Converter Assembly ...................................................................... 208
Figure 8-4. Critical Flow Orif ice Assembly ........................................................................ 210
Figure 9-1. Viewing and Clearing Warning Messages .......................................................... 214
Figure 9-2. Example of Signal I/O Function ....................................................................... 218
Figure 9-3. CPU Status Indicator..................................................................................... 219
Figure 9-4. Shutter Assembly ......................................................................................... 237
Figure 9-5. Location of UV Reference Detector Potentiometer............................................... 238
Figure 9-6. Pre-Amplif ier Board Layout ............................................................................ 240
Figure 10-1. UV Absorption ............................................................................................ 247
Figure 10-2. UV Light Path............................................................................................. 249
Figure 10-3. Source UV Lamp Construction ....................................................................... 250
Figure 10-4. Excitation Lamp UV Spectrum Before/After Filtration......................................... 251
Figure 10-5. PMT Optical Filter Bandw idth ........................................................................ 252
Figure 10-6. Effects of Focusing Source UV in Sample Chamber............................................ 252
Figure 10-7. T101 Gas Flow and Location of Critical Flow Orif ice ........................................... 256
xv