Kyocera KM-C2520 Service Manual page 150

2FZ/2F0/2HC
Emulation mode selection
Change the emulation mode.
1. Press [Emulation].
2. Press the interface to be configured.
3. Select the desired emulation.
PCL6/KPDL/KPDL (Auto) /KC-GL
For [KPDL (Auto)], select KPDL (Auto) alternate
emulation.
For [KPDL] or [KPDL (Auto)], configure the KPDL
error printing setting.
For [KC-GL], configure the pen and printing envi-
ronment settings.
4. Press [Close].
Selecting alternate emulation
When [KPDL (Auto)] emulation is selected, KPDL or
alternate emulation is set automatically depending on the
print data.
1. Refer to steps 1 to 3 of Emulation Mode Selection
to select [KPDL (Auto)].
2. Press [Alt. Emulation].
3. Press [PCL6] or [KC-GL].
4. Press [Close].
Print KPDL errors
When printing in KPDL emulation mode, prints details of
any errors that occur.
1. Refer to steps 1 to 3 of Emulation Mode Selection
to select [KPDL] or [KPDL (Auto)].
2. Press [Print KPDL errors].
3. Select [On] or [Off].
4. Press [Close].
Pen and print environment setting
Specify 8 different pen thicknesses, pen color and page
sizes when KC-GL emulation is selected.
1. Refer to steps 1 to 3 of Emulation Mode Selection
to select [KC-GL].
2. Press [Pen Adjust].
3. Select the pen to configure using the cursor up/
down keys and press [Change #].
4. Press [+] or [-] to set the pen thickness (in dots).
Setting range: 1 - 99 dots
5. Press desired pen color.
Black/Blue/Red/Magenta/Green/Cyan/Yellow/White
6. Press [Close].
7. Press [Close].
8. Press [Page Set].
9. Press the button corresponding to the desired size.
A2/A1/A0/B3/B2/B1/B0/SPSZ
[SPSZ] is the size specified by the prescribed
SPSZ command.
10. Press [Close].
1-3-110
Font selection
Select the default font.
1. Press [Font].
2. Press [Font selection].
3. Press the interface to be configured.
4. Select the Font ID using the cursor up/down keys.
I: Internal Font
SO: Soft font (downloaded)
MO: Font stored on memory card
HO: Font stored or RAM disk or hard disk
5. Press [Close].
Font size setting
Set the default font size.
When the default font is set to Courier or Letter Gothic,
the text pitch setting is shown instead of this menu.
1. Refer to steps 1 - 3 of Font Selection to select the
interface.
2. Press [Detail].
3. Press [+] or [-] to set the font size.
Set between 4.00 - 999.75 points in 0.25 point
increments.
4. Press [Close].
Courier/letter gothic font character pitch setting
Set the character pitch for Courier or Letter Gothic fonts.
1. Refer to steps 1 - 3 of Font Selection to select the
interface.
2. Press [Detail].
3. Press [+] or [-] to set the pitch size.
Set between 0.44 - 99.99 pitch in 0.01 pitch incre-
ments.
4. Press [Close].
Courier/letter gothic font thickness setting
Select the Courier/Letter Gothic font Thickness.
1. Refer to steps 1 - 3 of Font Selection to select the
interface.
2. Press [Internal] or [Dark] in the [Courier] area.
3. Press [Internal] or [Dark] in the [Letter Gothic] area.
4. Press [Close].
Code set selection
When emulation is set to PCL6 and the internal font is
selected as the default font, select the character code
set. The available code sets depend on which font is cur-
rently selected.
1. Press [Font].
2. Press [Code Set].
3. Press the interface to be configured.
4. Select the Code Set using the cursor up/down
keys.
5. Press [Close].