Ricoh J001 Service Manual page 248

Service Center Call
Event
Response
Paper jams During paper feed from Tray 2,
between the the trailing edge sensor
trailing edge switched on, but the registration
sensor and sensor did not detect the paper,
registration even though it fed to the
sensor prescribed position. Make sure
(Paper does not that there is no paper inside the
arrive at the printer.
registration
sensor)
Tray 2
Paper jams During duplex printing, or when
between the
the sheet is exiting before
trailing edge reversal in the duplex unit, the
sensor and trailing edge sensor switched
registration on, but the registration sensor
sensor
did not detect the paper, even
(Paper does not though it fed to the prescribed
arrive at the position.
registration (The registration sensor detects
sensor) the leading edge of the
Duplexing reversed paper from the duplex
unit.) Make sure there is no
paper in the printer.
Initial jam - At power on, or during printer
(At initialization initialization, the trailing edge
the trailing sensor goes on. Make sure that
edge sensor there is no paper inside the
switches on.) printer.
Bypass tray jam At power on, or during printer
(paper remains) initialization, the bypass set
sensor goes on.
When Tray 1 or Tray 2 is used
for paper feed, the bypass set
sensor goes on. Check the
bypass tray for paper.
SM
CÓPIA NÃO CONTROLADA
Probable Cause
The paper is folded or caught in the
paper feed path.
- The paper is folded or caught in the
paper feed path.
- Paper remains in the paper path.
- Feed clutch defective.
Paper remains in the bypass tray.
CÓPIA NÃO CONTROLADA
Operator Action
(1) If Tray 2 has paper loaded, remove (1) If Tray 2 has paper loaded, remove the paper
the paper from the tray. from the tray.
(2) If the duplex unit is not attached, open the
(2) If the duplex unit is not attached, rear cover of the printer, open the reverse guide
open the rear cover of the printer, open and remove the paper.
the reverse guide and remove the (3) If the duplex unit is attached, detach it, open
paper. the reverse guide, and then remove the jammed
paper.
(3) If the duplex unit is attached, detach (4) Open the rear cover of Tray 2, remove the
it, open the reverse guide, and then jammed paper, and then press [Paper Feed] on
remove the jammed paper. the printer operation panel.
(4) Open the rear cover of Tray 2,
remove the jammed paper, and then
press [Paper Feed] on the printer
operation panel.
(1) Remove the duplex unit from the - Remove the duplex unit from the printer, open
printer, open the reverse guide. the reverse guide.
- Remove the paper.
(2) Remove the paper. - After removing the jam, press the [Paper Feed]
button on the printer.
(3) After removing the jam, press the
[Paper Feed] button on the printer.
(1) If the duplex unit is not attached, (1) If the duplex unit is not attached, open the
open the rear cover of the printer, open rear cover of the printer, open the reverse guide
the reverse guide and remove the and remove the paper.
paper. (2) If the duplex unit is attached, open the rear
cover of the duplex unit, open the reverse guide,
(2) If the duplex unit is attached, open remove the jammed paper, and then press the
the rear cover of the duplex unit, open [Paper Feed] key on the printer operation panel.
the reverse guide, remove the jammed
paper, and then press the [Paper Feed]
key on the printer operation panel.
(1)Remove the paper from the bypass Remove the paper from the bypass tray.
tray. - After removing the jam, press the [Paper Feed]
button on the printer.
(2) After removing the jam, press the
[Paper Feed] button on the printer.
8-48
Problem Solution
Content User ST
X
X
X
X
J001/J003
NRC