FUTABA T16IZ SUPER Full Manual page 9

Digital proportional r/c system
Hide thumbs Also See for T16IZ SUPER:
Table of Contents

Advertisement

WARNING
Never grasp the transmitter antenna while flying.
■ The transmitter output may drop drastically.
Always  make  sure  that  all  transmitter  stick  move-
ments operate all servos properly in the model prior to 
flight.    Also,  make  sure  that  all  switches,  etc.  function 
properly as well.  If there are any difficulties, do not use 
the system until all inputs are functioning properly. 
Never fly in range check mode. 
■ In the dedicated range test range check mode, the transmitter 
output range is reduced and may cause a crash.
While operating, never touch the transmitter with, or 
bring  the  transmitter  near,  another  transmitter,  a  cell-
phone, or other wireless devices.
■ Doing so may cause erroneous operation.
Do not point the antenna directly toward the aircraft 
during flight. 
■ The antenna is directional and the transmitter output is 
weakest. (The strength of the radio waves is greatest from the 
sides of the antenna.)
Never fly on a rainy day, when the wind is strong, or 
at night. 
■ Water could lead to failure or improper functionality and poor 
control of the aircraft which could lead to a crash. 
Never turn the power switch off during flight or while 
the engine or motor is running. 
■ Operation will become impossible and the aircraft will crash. 
Even if the power switch is turned on, operation will not begin 
until transmitter and receiver internal processing is complete.
Do  not  start  the  engine  or  motor  while  wearing  the 
neck strap.  
■ The neck strap may become entangled with the rotating 
propeller, rotor, etc. and cause a serious injury.
Do  not  fly  when  you  are  physically  impaired  as  it 
could pose a safety hazard to yourself or others.
Do not fly at the following places:   
■ Near another radio control flying field.
■ Near or above people.
■ Near homes, schools, hospitals or other places where people 
congregate.
■ Near high voltage lines, high structures, or communication 
facilities.
When setting the transmitter on the ground during 
flight preparations, do not stand it upright.
■ The transmitter may tip over, the sticks may move and the 
propeller or rotor may rotate unexpectedly and cause injury. 
Do  not  touch  the  engine,  motor,  or  ESC  during  and 
immediately after use. 
■ These items may become hot during use. 
For safety, fly so that the aircraft is visible at all times.
   
■ Flying behind buildings or other large structures will not only 
cause you to lose sight of the aircraft, but also degrade the RF 
link performance and cause loss of control. 
From the standpoint of safety, always set the fail safe 
function.   
■ In particular, normally set the throttle channel to idle. For a 
helicopter, set the throttle channel to maintain a hover.  
When  flying,  always  return  the  transmitter  setup 
screen to the Home screen.
■ Erroneous input during flight is extremely dangerous. 
Always  check  the  remaining  capacity  of  the  trans-
mitter and receiver batteries before each flying session 
prior to flight. 
■ Low battery capacity will cause loss of control and a crash.  
Always  check  operation  of  each  control  surface  and 
perform  a  range  test  before  each  flying  session.  Also, 
when using the trainer function, check the operation of 
both the teacher and student transmitter. 
■ Even one incorrect transmitter setting or aircraft abnormality 
can cause a crash. 
Before turning on the transmitter:
1. Always move the transmitter throttle stick position to the 
minimum (idle) position. 
2. Turn on the transmitter first and then the receiver.
When  turning  off  the  transmitterʼ s  power  switch 
after the engine or motor has stopped (state in which it 
will not rotate again):
1. Turn off the receiver power switch. 
2. Then turn off the transmitter power switch.
■ If the power switch is turned on/off in the opposite order, the 
propeller may rotate unexpectedly and cause a serious injury.
■ Also always observe the above order when setting the fail safe 
function.
When adjusting the transmitter, stop the engine ex-
cept when necessary. In the case of a motor, disconnect 
the  wiring  that  allows  it  to  continue  operation.  When 
doing  so,  please  exercise  extreme  caution.  Ensure  that 
the aircraft is secured and that it will not come into con-
tact with anything or anyone. Ensure that the motor will 
not rotate prior to making any adjustments.           
■ Unexpected high speed rotation of the engine/motor may 
cause a serious injury. 
9

Hide quick links:

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the T16IZ SUPER and is the answer not in the manual?

Questions and answers

Table of Contents

Save PDF