Danfoss FC 300 Programming Manual page 76

Parameter Descriptions
5-33 Term X30/7 Digi Out (MCB 101)
Option:
[17] Above speed, high
[18] Out of feedb. range
[19] Below feedback, low
3 3
[20] Above feedback, high
[21] Thermal warning
[22] Ready,no thermal W
[23] Remote,ready,no TW
[24] Ready, Voltage OK
[25] Reverse
[26] Bus OK
[27] Torque limit & stop
[28] Brake, no brake war
[29] Brake ready, no fault
[30] Brake fault (IGBT)
[31] Relay 123
[32] Mech brake ctrl
[33] Safe stop active
[39] Tracking error
[40] Out of ref range
[41] Below reference, low
[42] Above ref, high
[43] Extended PID Limit
[45] Bus ctrl.
[46] Bus ctrl, 1 if timeout
[47] Bus ctrl, 0 if timeout
[51] MCO controlled
[60] Comparator 0
[61] Comparator 1
[62] Comparator 2
[63] Comparator 3
[64] Comparator 4
[65] Comparator 5
[70] Logic rule 0
[71] Logic rule 1
[72] Logic rule 2
[73] Logic rule 3
[74] Logic rule 4
[75] Logic rule 5
[80] SL digital output A
[81] SL digital output B
[82] SL digital output C
[83] SL digital output D
[84] SL digital output E
[85] SL digital output F
[120] Local ref active
[121] Remote ref active
[122] No alarm
[123] Start command activ
[124] Running reverse
[125] Drive in hand mode
[126] Drive in auto mode
76
FC 300 Programming Guide
Function:
®
MG.33.M9.02 - VLT is a registered Danfoss trademark
3.7.4 5-4* Relays
Parameters for configuring the timing and the output
functions for the relays.
5-40 Function Relay
Array [9]
(Relay 1 [0], Relay 2 [1], Relay 3 [2] (MCB 113), Relay 4 [3] (MCB 113),
Relay 5 [4] (MCB 113), Relay 6 [5] (MCB 113), Relay 7 [6] (MCB 105),
Relay 8 [7] (MCB 105), Relay 9 [8] (MCB 105))
Option: Function:
[0] No operation All digital and relay outputs are default
*
set to "No Operation".
[1] Control ready The control card is ready. E.g.:
Feedback from a drive where the
control is supplied by an external 24 V
(MCB 107) and the main power to
drive is not detected.
[2] Drive ready Drive is ready to operate. Mains and
control supplies are OK.
[3] Drive rdy/rem ctrl The frequency converter is ready for
operation and is in Auto On mode
[4] Enable / no warning Ready for operation. No start or stop
commands have been applied (start/
disable). No warnings are active.
[5] Running Motor is running, and shaft torque
present.
[6] Running / no Output speed is higher than the speed
warning set in par. 1-81 Min Speed for Function
at Stop [RPM] Min Speed for Function
at Stop [RPM]. The motor is running
and no warnings.
[7] Run in range/no Motor is running within the program-
warn med current and speed ranges set in
par. 4-50 Warning Current Low and
par. 4-53 Warning Speed High. No
warnings.
[8] Run on ref/no warn Motor runs at reference speed. No
warnings.
[9] Alarm An alarm activates the output. No
warnings
[10] Alarm or warning An alarm or a warning activates the
output.
[11] At torque limit The torque limit set in par. 4-16 Torque
Limit Motor Mode or par. 4-17 Torque
Limit Generator Mode has been
exceeded.
[12] Out of current The motor current is outside the range
range set in par. 4-18 Current Limit.
[13] Below current, low Motor current is lower than set in
par. 4-50 Warning Current Low.