Danfoss FC 300 Programming Manual page 203

Index
Rated Motor Speed
RCD
Readout Bus Off Counter 10-07
Readout Filtering 8-08
Readout Receive Error Counter 10-06
Readout Transmit Error Counter 10-05
Readout: Edit Set-ups / Channel 0-14
Readout: Linked Set-ups 0-13
Reference
[Reference %] 16-02
Reference Function 3-04
Reference Range 3-00
Reference Resource 1 3-15
Reference Resource 2 3-16
Reference Resource 3 3-17
Reference Site 3-13
[Reference Unit] 16-01
Reference/feedback Unit 3-01
Regional Settings 0-03
Relative Scaling Reference Resource 3-18
[Relay Output Bin] 16-71
Relay Outputs
Release Brake Current 2-20
Reset
Reset Control Word Timeout 8-06
Reset kWh Counter 15-06
Reset Mode 14-20
Reset Running Hours Counter 15-07
Reset SLC 13-03
[Reset] Key On Lcp 0-43
Resolution (Positions/Rev) 17-21
Resolution (PPR) 17-11
Resolver Interface 17-59
Resonance Dampening 1-64
Resonance Dampening Time Constant 1-65
Reversing Select 8-54
RFI Filter 14-50
Rotor Leakage Reactance (x2) 1-34
Rotor Resistance (rr) 1-31
Running Hours 15-01
S
Safety Precautions
Samples Before Trigger 15-14
Screened/armoured
Serial Communication
Service Code 14-29
Setpoint 9-00
Set-up Copy 0-51
Set-up Select 8-55
Signal Type 17-10
SL Controller Action 13-52
SL Controller Event 13-51
SL Controller Mode 13-00
SL Controller State 16-38
SL Controller Timer 13-20
Slave Error Count 8-83
Slave Messages Rcvd 8-82
Slip Compensation 1-62
Slip Compensation Time Constant 1-63
Software Version 15-43
Speed PID Diff. Gain Limit 7-05
Speed PID Differentiation Time 7-04
Speed PID Feed Forward Factor 7-08
Speed PID Feedback Gear Ratio 7-07
Speed PID Feedback Source 7-00
FC 300 Programming Guide
4 Speed PID Integral Time 7-03
5 Speed PID Lowpass Filter Time 7-06
114 Speed PID Proportional Gain 7-02
100 [Speed RPM] 16-17
114 Speed Up/down
114 SSI Data Format 17-26
26 SSI Data Length 17-24
26 Stall Protection 14-35
119 Start Current 1-76
146 Start Delay
53 Start Event 13-01
52 Start Function
54 Start Select 8-53
54 [Start Speed Hz] 1-75
54 [Start Speed Rpm] 1-74
54 Start/stop
146 Stator Leakage Reactance
52 Stator Leakage Reactance (x1) 1-33
24 Stator Resistance (rs) 1-30
55 Status
150 Status Messages
72 Status Word 16-03
50 Status Word 1 9-68
14 Step Size 3-90
100 Step-by-step
142 Stop Delay 2-24
137 Stop Event 13-02
142 Store Always 10-33
124 Store Data Values 10-31
32 SW ID Control Card 15-49
152 SW ID Power Card 15-50
152 Switching Frequency 14-01
153 Switching Pattern 14-00
41 Synchronous Motor Speed
41
106
T
139
Telegram Selection 8-40
37
Temp. Input X48/10 18-39
37
Temp. Input X48/4 18-37
142
Temp. Input X48/7 18-38
Temperature Sensor Alarm Function 35-06
Term 32/33 Encoder Direction 5-71
6 Term 32/33 Pulses Per Revolution 5-70
143 Term X30/6 Digi Out (mcb 101) 5-32
9 Term X30/7 Digi Out (mcb 101) 5-33
4 Term. 29 High Frequency 5-51
138 Term. 29 High Ref./feedb. Value 5-53
108 Term. 29 Low Frequency 5-50
32 Term. 29 Low Ref./feedb. Value 5-52
106 Term. 33 High Frequency 5-56
152 Term. 33 High Ref./feedb. Value 5-58
132 Term. 33 Low Frequency 5-55
131 Term. 33 Low Ref./feedb. Value 5-57
122 Term. X30/11 Filter Time Constant 6-36
148 Term. X30/11 High Ref./feedb. Value 6-35
128 Term. X30/11 Low Ref./feedb. Value 6-34
107 Term. X30/12 Filter Time Constant 6-46
107 Term. X30/12 High Ref./feedb. Value 6-45
41 Term. X30/12 Low Ref./feedb. Value 6-44
41 Term. X48/10 Filter Time Constant 35-34
145 Term. X48/10 High Temp. Limit 35-37
94 Term. X48/10 Input Type 35-05
94 Term. X48/10 Low Temp. Limit 35-36
96 Term. X48/10 Temp. Monitor 35-35
96 Term. X48/10 Temp. Unit 35-04
94 Term. X48/2 Filter Time Constant 35-46
®
MG.33.M9.02 - VLT is a registered Danfoss trademark
94
95
94, 156
147
10
152
152
139
43
42
122
42
106
43
42
9
36
37
37
13
12
146
112
61
20
50
123
117
117
145
145
134
134
4
102, 109
154
154
154
157
83
83
75
75
80
80
80
80
80
81
80
81
87
87
87
87
87
87
158
158
157
158
158
157
158
203