Danfoss FC 300 Programming Manual page 204

Index
Term. X48/2 High Current 35-43
Term. X48/2 High Ref./feedb. Value 35-45
Term. X48/2 Low Current 35-42
Term. X48/2 Low Ref./feedb. Value 35-44
Term. X48/4 Filter Time Constant 35-14
Term. X48/4 High Temp. Limit 35-17
Term. X48/4 Input Type 35-01
Term. X48/4 Low Temp. Limit 35-16
Term. X48/4 Temp. Monitor 35-15
Term. X48/4 Temp. Unit 35-00
Term. X48/7 Filter Time Constant 35-24
Term. X48/7 High Temp. Limit 35-27
Term. X48/7 Input Type 35-03
Term. X48/7 Low Temp. Limit 35-26
Term. X48/7 Temp. Monitor 35-25
Term. X48/7 Temp. Unit 35-02
Terminal 27 Mode 5-01
Terminal 27 Pulse Output Variable 5-60
Terminal 29 Mode 5-02
Terminal 29 Pulse Output Variable 5-63
Terminal 37 Safe Stop 5-19
Terminal 42 Output 6-50
Terminal 42 Output Bus Control 6-53
Terminal 42 Output Max Scale 6-52
Terminal 42 Output Min Scale 6-51
Terminal 42 Output Timeout Preset 6-54
Terminal 53 Filter Time Constant 6-16
Terminal 53 High Current 6-13
Terminal 53 High Ref./feedb. Value 6-15
Terminal 53 High Voltage 6-11
Terminal 53 Low Current 6-12
Terminal 53 Low Ref./feedb. Value 6-14
Terminal 53 Low Voltage 6-10
Terminal 53 Switch Setting 16-61
Terminal 54 Filter Time Constant 6-26
Terminal 54 High Current 6-23
Terminal 54 High Ref./feedb. Value 6-25
Terminal 54 High Voltage 6-21
Terminal 54 Low Current 6-22
Terminal 54 Low Ref./feedb. Value 6-24
Terminal 54 Low Voltage 6-20
Terminal 54 Switch Setting 16-63
Terminal X30/11 High Voltage 6-31
Terminal X30/11 Low Voltage 6-30
Terminal X30/12 High Voltage 6-41
Terminal X30/12 Low Voltage 6-40
Terminal X30/6 Pulse Output Variable 5-66
Terminal X30/8 Bus Control 6-63
Terminal X30/8 Max. Scale 6-62
Terminal X30/8 Min. Scale 6-61
Terminal X30/8 Output 6-60
Terminal X30/8 Output Timeout Preset 6-64
Terminal X45/1 Output Min Scale, 6-71
Terminal X45/3 Output Min Scale, 6-81
Thermal Load
Thermistor
Thermistor Source 1-93
This Set-up Linked To 0-12
[Torque %] 16-22
[Torque %] High Res. 16-21
Torque Characteristics 1-03
Torque Limit Factor Source 4-20
Torque Limit Generator Mode 4-17
Torque Limit Motor Mode 4-16
[Torque Nm] 16-16
[Torque Nm] High 16-25
Torque PI Integration Time 7-13
204
FC 300 Programming Guide
158 Torque PI Proportional Gain 7-12
158 Torque Ramp Time 2-27
158 Torque Ref 2-26
158 Tracking Error 4-35
157 Tracking Error After Ramping Timeout 4-39
157 Tracking Error Function 4-34
157 Tracking Error Ramping 4-37
157 Tracking Error Ramping Timeout 4-38
157 Tracking Error Timeout 4-36
157 Transformation Ratio 17-53
157 Trigger Event 15-12
158 Trip Delay At Current Limit 14-24
157 Trip Delay At Inverter Fault 14-26
158 Trip Delay At Torque Limit 14-25
158 Trip Reset
157
67
U
81
U/f Characteristic - F 1-56
67
U/f Characteristic - U 1-55
82
Unit For User-defined Readout 0-30
71
88
V
89
89
Value
89
Voltage 15-42
89
Voltage Reduction In Fieldweakening 1-54
86
Voltage Reference Via A Potentiometer
86
VT Level 14-40
86
VVCplus
85
85
W
86
85
Warning Current High 4-51
149
Warning Current Low 4-50
86
Warning Feedback High 4-57
86
Warning Feedback Low 4-56
86
Warning Parameter 10-13
86
Warning Reference High 4-55
86
Warning Reference Low 4-54
86
Warning Speed High 4-53
86
Warning Speed Low 4-52
149
Warning Word
87
Warning Word 2 16-93
87
Warnings
87
Wobble Delta Freq. Scaled 30-19
87
Wobble Delta Freq. Scaling Resource 30-03
82
[Wobble Delta Frequency %] 30-02
91
[Wobble Delta Frequency Hz] 30-01
91
[Wobble Jump Frequency %] 30-05
91
[Wobble Jump Frequency Hz] 30-04
90
Wobble Jump Time 30-06
91
Wobble Mode 30-00
92
Wobble Random Function 30-09
93
Wobble Random Ratio Max. 30-11
38, 147
Wobble Random Ratio Min. 30-12
44
Wobble Ratio 30-10
46
Wobble Sequence Time 30-07
25
Wobble Up/ Down Time 30-08
147
147
34
63
63
63
147
148
96
®
MG.33.M9.02 - VLT is a registered Danfoss trademark
96
51
51
65
65
64
65
65
65
153
143
138
138
138
137
40
40
30
20
145
39
11
139
6
65
65
66
66
116
66
66
66
65
100, 151
151
190
156
155
155
155
155
155
155
154
155
155
155
155
155
155