Danfoss FC 300 Programming Manual page 31

Parameter Descriptions
0-30 Unit for User-defined Readout
Option: Function:
[125] ft3/s
[126] ft3/min
[127] ft3/h
[130] lb/s
[131] lb/min
[132] lb/h
[140] ft/s
[141] ft/min
[145] ft
[160] °F
[170] psi
[171] lb/in2
[172] in WG
[173] ft WG
[180] HP
0-31 Min Value of User-defined Readout
Range: Function:
0.00 Custom- [Application This parameter sets the min. value of
ReadoutUnit dependant] the custom defined readout (occurs
*
at zero speed). Only possible to set
different from 0 is when selecting a
linear unit in par. 0-30 Unit for User-
defined Readout. For Quadratic and
Cubic units the minimum value will
be 0.
0-32 Custom Readout Max Value
Range: Function:
100.00 [Application This parameter sets the max value to
CustomRea- dependant] be shown when the speed of the
doutUnit motor has reached the set value for
*
par. 4-13 Motor Speed High Limit
[RPM] or par. 4-14 Motor Speed High
Limit [Hz] (depends on setting in
par. 0-02 Motor Speed Unit).
0-37 Display Text 1
Range: Function:
0 [0 - 0 ] Enter a text which can be viewed in the graphical
*
display by selecting Display Text 1 [37] in par. 0-20,
0-21, 0-22, 0-23 or 0-24.
0-38 Display Text 2
Range: Function:
0 [0 - 0 ] Enter a text which can be viewed in the graphical
*
display by selecting Display Text 2 [38] in par. 0-20,
0-21, 0-22, 0-23 or 0-24.
FC 300 Programming Guide
0-39 Display Text 3
Range:
0
*
3.2.5 0-4* LCP Keypad
Enable, disable and password protect individual keys on the
LCP.
0-40 [Hand on] Key on LCP
Option:
[0]
[1]
[2]
[3]
[4]
0-41 [Off] Key on LCP
Option:
[0]
[1]
[2]
0-42 [Auto on] Key on LCP
Option:
[0]
[1]
[2]
®
MG.33.M9.02 - VLT is a registered Danfoss trademark
Function:
[0 - 0 ] Enter a text which can be viewed in the graphical
display by selecting Display Text 3 [39] in par. 0-20,
0-21, 0-22, 0-23 or 0-24.
Function:
Disabled No effect when [Hand on] is pressed. Select
[0] Disabled to avoid accidental start of the
drive in Hand on mode.
Enabled The LCP switches to Hand on mode directly
*
when [Hand on] is pressed.
Password After pressing [Hand on] a password is
required. If par. 0-40 is in included in My
Personal Menu, define the password in par.
0-65, Personal Menu Password. Otherwise
define the password in par. 0-60, Main Menu
Password
Hand Off/On When [Hand on] is pressed once, the LCP
switches to Off mode. When pressed again,
the LCP switches to Hand on mode.
Hand Off/On Same as [3] but a password is required (see
w. Passw. [2]).
Function:
Disabled Avoids accidental stop of the frequency converter.
*
Enabled
*
Password Avoids unauthorised stop. If par. 0-41 [Off] Key on
LCP is included in the Quick Menu, then define the
password in par. 0-65 Quick Menu Password.
Function:
Disabled Avoid accidental start of the frequency converter
*
in Auto mode.
Enabled
*
Password Avoids unauthorised start in Auto mode. If
par. 0-42 [Auto on] Key on LCP is included in the
Quick Menu, then define the password in
par. 0-65 Quick Menu Password.
3 3
31