Danfoss FC 300 Programming Manual page 123

Parameter Descriptions
13-01 Start Event
Option: Function:
Feedback Low and par. 4-57 Warning
Feedback High.
[14] Below feedb. Below feedb. Low [14] The feedback is below
low the limit set in par. 4-56 Warning Feedback
Low.
[15] Above feedb. Above feedb. High [15] The feedback is above
high the limit set in par. 4-57 Warning Feedback
High.
[16] Thermal Thermal warning [16] The thermal warning
warning turns on when the temperature exceeds the
limit in the motor, the frequency converter,
the brake resistor or the thermistor.
[17] Mains out of Mains out of range [17] The mains voltage is
range outside the specified voltage range.
[18] Reversing Reversing [18] The output is high when the
frequency converter is running counter
clockwise (the logical product of the status
bits "running" AND "reverse").
[19] Warning Warning [19] A warning is active.
[20] Alarm (trip) Alarm (trip) [20] A (trip) alarm is active.
[21] Alarm (trip Alarm (trip lock) [21] A (Trip lock) alarm is
lock) active.
[22] Comparator 0 Comparator 0 [22] Use the result of
comparator 0.
[23] Comparator 1 Comparator 1 [23] Use the result of
comparator 1.
[24] Comparator 2 Comparator 2 [24] Use the result of
comparator 2.
[25] Comparator 3 Comparator 3 [25] Use the result of
comparator 3.
[26] Logic rule 0 Logic rule 0 [26] Use the result of logic rule
0.
[27] Logic rule 1 Logic rule 1 [27] Use the result of logic rule
1.
[28] Logic rule 2 Logic rule 2 [28] Use the result of logic rule
2.
[29] Logic rule 3 Logic rule 3 [29] Use the result of logic rule
3.
[33] Digital input Digital input DI18 [33] Use the result of
DI18 digital input 18.
[34] Digital input Digital input DI19 [34] Use the result of
DI19 digital input 19.
[35] Digital input Digital input DI27 [35] Use the result of
DI27 digital input 27.
[36] Digital input Digital input DI27 [35] Use the result of
DI29 digital input 29.
FC 300 Programming Guide
13-01 Start Event
Option:
[37] Digital input
[38] Digital input
[39] Start command Start command [39] A start command is
[40] Drive stopped
[41] Reset Trip
[42] Auto-reset Trip Auto-reset Trip [42] An Auto reset is
[43] Ok key
[44] Reset key
[45] Left key
[46] Right key
[47] Up key
[48] Down key
[50] Comparator 4
[51] Comparator 5
[60] Logic rule 4
[61] Logic rule 5
13-02 Stop Event
Select the boolean (TRUE or FALSE) input to activate Smart Logic
Control.
Option:
[0]
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10] Out of speed range
[11] Below speed low
[12] Above speed high
[13] Out of feedb. range
[14] Below feedb. low
®
MG.33.M9.02 - VLT is a registered Danfoss trademark
Function:
Digital input DI32 [37] Use the result of
DI32 digital input 32.
Digital input DI33 [38] Use the result of
DI33 digital input 33.
issued.
Drive stopped [40] A stop command ( Jog,
Stop, Qstop, Coast) is issued – and not from
the SLC itself.
Reset Trip [41] A reset is issued
performed.
OK key [43] The Ok key is pressed.
Reset key [44] The reset key is pressed.
Left key [45] The left key is pressed.
Right key [46] The right key is pressed.
Up key [47] The up key is pressed.
Down key [48] The down key is pressed.
Comparator 4 [50] Use the result of
comparator 4.
Comparator 5 [51] Use the result of
comparator 5.
Logic rule 4 [60] Use the result of logic rule
4.
Logic rule 5 [61] Use the result of logic rule
5.
Function:
False For descriptions [0] - [61], see
*
par. 13-01 Start Event Start Event
True
Running
In range
On reference
Torque limit
Current limit
Out of current range
Below I low
Above I high
3 3
123