Danfoss FC 300 Programming Manual page 112

Parameter Descriptions
9-47 Fault Number
Range:
0 [0 - 0 ] This buffer contains the alarm number (e.g. 2 for live
*
zero error, 4 for mains phase loss) for all alarms and
warnings that have occurred since last reset or
3 3
power-up. The maximum buffer capacity is eight
error events.
9-52 Fault Situation Counter
Range:
0 [0 - 1000 ] This parameter displays the number of error
*
9-53 Profibus Warning Word
Range:
0 N/A [0 - 65535 N/A] This parameter displays Profibus
*
Read only
Bit: Meaning:
0 Connection with DP-master is not ok
1 Not used
2 FDLNDL (Fieldbus Data link Layer) is not ok
3 Clear data command received
4 Actual value is not updated
5 Baudrate search
6 PROFIBUS ASIC is not transmitting
7 Initialisation of PROFIBUS is not ok
8 Frequency converter is tripped
9 Internal CAN error
10 Wrong configuration data from PLC
11 Wrong ID sent by PLC
12 Internal error occured
13 Not configured
14 Timeout active
15 Warning 34 active
9-63 Actual Baud Rate
Option:
[0] 9,6 kbit/s
[1] 19,2 kbit/s
[2] 93,75 kbit/s
[3] 187,5 kbit/s
[4] 500 kbit/s
[6] 1500 kbit/s
[7] 3000 kbit/s
112
Function:
Function:
events which have occurred since last reset of
power-up.
Function:
communication warnings. Please refer to
the Profibus Operating Instructions for
further information.
Function:
This parameter displays the actual
Profibus baud rate. The Profibus
Master automatically sets the baud
rate.
MG.33.M9.02 - VLT
FC 300 Programming Guide
9-63 Actual Baud Rate
Option:
[8] 6000 kbit/s
[9] 12000 kbit/s
[10] 31,25 kbit/s
[11] 45,45 kbit/s
[255] No baudrate found
*
9-64 Device Identification
Range:
0 [0 - 0 ] This parameter displays the device identification.
*
9-65 Profile Number
Range:
0 N/A
*
NOTE
This parameter is not visible via LCP.
9-67 Control Word 1
Range:
0 [0 - 65535 ] This parameter accepts the Control Word from a
*
9-68 Status Word 1
Range:
0 [0 - 65535 ] This parameter delivers the Status Word for a
*
9-70 Programming Set-up
Option:
[0] Factory setup Uses default data. This option can be used as
[1] Set-up 1
[2] Set-up 2
[3] Set-up 3
[4] Set-up 4
[9] Active Set-up Follows the active set-up selected in
*
This parameter is unique to LCP and fieldbuses. See also
par. 0-11 Programming Set-up.
®
is a registered Danfoss trademark
Function:
Function:
Please refer to the Operating Instructions for Profibus,
MG.33.CX.YY for further explanation.
Function:
[0 - 0 N/A] This parameter contains the profile identifica-
tion. Byte 1 contains the profile number and
byte 2 the version number of the profile.
Function:
Master Class 2 in the same format as PCD 1.
Function:
Master Class 2 in the same format as PCD 2.
Function:
Select the set-up to be edited.
a data source to return the other set-ups to a
known state.
Edits Set-up 1.
Edits Set-up 2.
Edits Set-up 3.
Edits Set-up 4.
par. 0-10 Active Set-up.