Danfoss FC 300 Programming Manual page 32

Parameter Descriptions
0-43 [Reset] Key on LCP
Option:
[0] Disabled
*
[1] Enabled
*
3 3
[2] Password
[7] Enabled
without OFF
[8] Password
without OFF
3.2.6 0-5* Copy / Save
Copy parameter settings between set-ups and to/from the
LCP.
0-50 LCP Copy
Option:
[0] No copy
*
[1] All to LCP
[2] All from LCP
[3] Size indep. from LCP
[4] File from MCO to LCP
[5] File from LCP to MCO
[6] Data from DYN to
LCP
[7] Data from LCP to
DYN
[8] LCP Compare
This parameter cannot be adjusted while the motor is running.
32
FC 300 Programming Guide
Function:
No effect when [Reset] is pressed. Avoids
accidental alarm reset.
Avoids unauthorised resetting. If
par. 0-43 [Reset] Key on LCP is included in the
Quick Menu, then define the password in
par. 0-65 Quick Menu Password.
Resets the drive without setting it in Off
mode.
Resets the drive without setting it in Off
mode. A password is required when
pressing [Reset] (see [2]).
Function:
Copies all parameters in all set-ups
from the frequency converter
memory to the LCP memory.
Copies all parameters in all set-ups
from the LCP memory to the frequen-
cy converter memory.
Copy only the parameters that are
independent of the motor size. The
latter selection can be used to
programme several frequency
converters with the same function
without disturbing motor data.
MG.33.M9.02 - VLT
0-51 Set-up Copy
Option: Function:
[0] No copy No function
*
[1] Copy to set- Copies all parameters in the present Program-
up 1 ming Set-up (defined in par. 0-11 Programming
Set-up) to Set-up 1.
[2] Copy to set- Copies all parameters in the present Program-
up 2 ming Set-up (defined in par. 0-11 Programming
Set-up) to Set-up 2.
[3] Copy to set- Copies all parameters in the present Program-
up 3 ming Set-up (defined in par. 0-11 Programming
Set-up) to Set-up 3.
[4] Copy to set- Copies all parameters in the present Program-
up 4 ming Set-up (defined in par. 0-11 Programming
Set-up) to Set-up 4.
[9] Copy to all Copies the parameters in the present set-up
over to each of the set-ups 1 to 4.
3.2.7 0-6* Password
0-60 Main Menu Password
Range:
100 N/A [0 - 999 Define the password for access to the Main
*
N/A] Menu via the [Main Menu] key. If
par. 0-61 Access to Main Menu w/o Password
is set to Full access [0], this parameter will be
ignored.
0-61 Access to Main Menu w/o Password
Option:
[0] Full access Disables password defined in par. 0-60 Main
*
Menu Password.
[1] LCP: Read only Prevent unauthorized editing of Main Menu
parameters.
[2] LCP: No access Prevent unauthorized viewing and editing of
Main Menu parameters.
[3] Bus: Read only Read-only functions for parameters on
fieldbus and/or FC standard bus.
[4] Bus: No access No access to parameters is allowed via
fieldbus and/or FC standard bus.
[5] All: Read only Read-only function for parameters on LCP,
fieldbus or FC standard bus.
[6] All: No access No access from LCP, fieldbus or FC standard
bus is allowed.
If Full access [0] is selected then par. 0-60 Main Menu Password,
par. 0-65 Personal Menu Password and par. 0-66 Access to
Personal Menu w/o Password will be ignored.
®
is a registered Danfoss trademark
Function:
Function: