Page 1 ORIGINAL INSTRUCTIONS OPERATOR’S MANUAL B95C B95C TC B110C Tier 4B (ﬁnal) Tractor Loader Backhoe PIN NZHH03067 and after Part number 90453215 edition English November 2020 Replaces part number 51420356...
Page 2: Table Of Contents
Contents 1 GENERAL INFORMATION Note to the owner................1-1 Intended use.
Page 3 EXTERIOR CONTROLS Rotating beacon (Optional) ............3-25 Battery master switch.
Page 4 MOVING THE UNIT Job site travel................4-16 Before operating the machine .
Page 5 Capacities - B95C, B95C LR, and B95C TC ....... . .
Page 6 Initial 10 hours Wheels - Check............... . 7-35 Every 10 hours Checks at start-up and before each workshift (10 hours) .
Page 7 Diesel Exhaust Fluid (DEF)/AdBlue® in-line filter ........7-92 Every 1000 hours Hydraulic oil filter .
Page 8 Telematics - Overview with New Holland FleetForce™ ........
Page 9: General Information
Contact your NEW HOLLAND CONSTRUCTION dealer for any further information or assistance about your machine. Your dealer has NEW HOLLAND CONSTRUCTION approved service parts. Your dealer has technicians with special training that know the best methods of repair and maintenance for your machine. NEW HOLLAND CONSTRUCTION customer assistance is also available. Go to www.newholland.com.
Page 10: Intended Use
Tampering with or changing the setting of any hydraulic system valve is strictly forbidden. Failure to comply could result in minor or moderate injury. C0160A Backhoe loaders B95C - B95C LR - B95C TC - B110C have been designed to perform most earth-moving oper- ations.
Page 11 1 - GENERAL INFORMATION Spare parts The “non-genuine” spare parts have not been checked and authorized by the manufacturer. The assembly and/or use of such products may have negative effects on the machine design features and could impair its operation safety. The manufacturer is not liable for any damage caused by “non-genuine”...
Page 12: Electro-Magnetic Compatibility (Emc)
• The add‐on equipment must not interfere with the functioning of the on board electronics Failure to comply with these rules will render the NEW HOLLAND CONSTRUCTION warranty null and void. Product identification Record the Product Identification Numbers (PIN).
Page 13 1 - GENERAL INFORMATION Engine Model The PIN plate is located on the left-hand side of the oil pan below the water separator. RAIL11TLB0009AA Power shuttle transmission Model The PIN plate is on the lower right-hand side of the trans- mission.
Page 14 1 - GENERAL INFORMATION Rear axle Model The PIN plate is on the right-hand front side of the axle. View the PIN plate from under the machine. LEEN11T0344AA Cab with a certified Roll Over Protective Structure (ROPS) and Falling Object Protective Structure (FOPS). Model The PIN plate is on the left-hand side back post inside the LEEN12T0532AA_1...
Page 15: Read The Operator's Manual
• learns and practices safe use of machine controls in a safe, clear area before operating this machine on a job site. It is your responsibility to observe pertinent laws and regulations and follow NEW HOLLAND CONSTRUCTION in- structions on machine operation and maintenance.
Page 16: Machine Orientation
1 - GENERAL INFORMATION Machine orientation The terms right-hand and left-hand, when used in this manual, indicate the right and left sides of the machine as seen from the operator's seat. Operator and seat in the driving and loader operation position Front side Rear side Right-hand side...
Page 17: Component Identification
1 - GENERAL INFORMATION Component identification RAIL15TLB0249FA Loader bucket Left-hand side stabilizer Loader bucket cylinder and linkage Entry or exit steps Cab with Roll Over Protective Structure (ROPS) Fuel tank Backhoe dipper or telescopic dipper (DEF)/A ® tank IESEL XHAUST LUID Backhoe bucket Loader arm lift cylinder with safety support strut...
Page 18 1 - GENERAL INFORMATION RAIL15TLB0250FA Right-hand side stabilizer Battery compartment Exhaust stack Entry or exit steps Engine hood Rear axle Front axle Swing lock pin (lock position) Hydraulic tank Backhoe boom lock (hydraulic or mechanical) 1-10...
Page 19: Selective Catalytic Reduction (Scr) Exhaust Treatment - Product Overview
What is Selective Catalytic Reduction (SCR)? Your NEW HOLLAND CONSTRUCTION machine is equipped with additional components to comply with national and local exhaust emissions requirements. The main components of the SCR system include the SCR catalyst, the Diesel Exhaust Fluid (DEF)/AdBlue® dosing module, and the DEF/A ®...
Page 20 3. Start the machine. Thawing • Your NEW HOLLAND CONSTRUCTION machine is equipped with an internal tank heater to thaw frozen DEF/ ®. Your machine will still function until the DEF/A ® begins to flow. The SCR system will then function normally.
Page 21 ®, prolonged transportation or storage above 25 °C (77 °F) should be avoided. ² Significant loss of shelf life: check every batch before use. See your NEW HOLLAND CONSTRUCTION dealer for more information on testing. NOTE: The main factors taken into account to define the shelf life in the table above are the ambient storage tem- perature and the initial alkalinity of DEF/A ®.
Page 22 1 - GENERAL INFORMATION SCR Catalyst Full Display Audible alert Action 1. Place the FORWARD-NEUTRAL-REVERSE (F-N-R) lever in the NEUTRAL position. 2. Engage the park brake. Constant audible alarm 3. Use the hand throttle and manually increase the engine speed to 1500 RPM. with illumination NOTE: The operator does not need to stay with the machine during the Hydrocarbon management procedure.
Page 23 • Claims involving the inspection or reconditioning of units after storage or prior use. • Repairs arising from service performed by agents not approved by NEW HOLLAND CONSTRUCTION. • Repairs arising from any unauthorized modification to the product or the use of non- NEW HOLLAND CONSTRUC- TION parts, implements or attachments.
Page 24 FPT Industrial S.p.A. recommends that you retain all receipts covering maintenance on your off- road engine, but NEW HOLLAND CONSTRUCTION cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all scheduled maintenance.
Page 25: Safety Information
2 - SAFETY INFORMATION 2 - SAFETY INFORMATION###_2_### Safety rules and signal word definitions Personal safety This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible death or injury. Throughout this manual and on machine safety signs, you will find the signal words DANGER, WARNING, and CAU- TION followed by special instructions.
Page 26: Safety Rules
2 - SAFETY INFORMATION Safety rules General safety rules Use caution when you operate the machine on slopes. A person or pet within the operating area of a machine can Raised equipment, full tanks and other loads will change be struck or crushed by the machine or its equipment. DO the center of gravity of the machine.
Page 27 2 - SAFETY INFORMATION When, due to exceptional circumstances, you decide to 3. Move the operator’s seat to the backhoe operating keep the engine running after you leave the operator’s position and choose one of the following backhoe station, then you must follow these precautions: positions: ○...
Page 28 2 - SAFETY INFORMATION Wheels and tires Make sure that tires are correctly inflated. Do not exceed wheel to a tire shop or your dealer for service. Explosive any recommended load or pressure. Follow the instruc- separation of the tire can cause serious injury. tions in the manual for proper tire inflation.
Page 29 2 - SAFETY INFORMATION General battery safety Always wear eye protection when you work with batteries. Follow the manufacturer’s instructions when you store and handle batteries. Do not create sparks or have open flame near a battery. Battery post, terminals, and related accessories contain Ventilate the area when you charge a battery or use a lead and lead compounds.
Page 30 2 - SAFETY INFORMATION Seat belts Seat belts must be worn at all times. • Check that bolts are tight on the seat bracket or mount- ing. Seat belt inspection and maintenance: • If the belt is attached to the seat, make sure that the •...
Page 31 2 - SAFETY INFORMATION Operator protective structure Your machine is equipped with an operator protective After an accident, fire, tip over, or roll over, the following structure, such as: a Roll Over Protective Structure MUST be performed by a qualified technician before (ROPS), Falling Objects Protective Structure (FOPS), returning the machine to field or job-site operations: or a cab with a ROPS.
Page 32 2 - SAFETY INFORMATION Do Not Operate tag Before you start servicing the machine, attach a ‘Do Not Operate’ warning tag to the machine in an area that will be visible. RH99E029 Hazardous chemicals If you are exposed to or come in contact with hazardous Dispose of all fluids, filters, and containers in an environ- chemicals you can be seriously injured.
Page 33 2 - SAFETY INFORMATION Electrical storm safety Do not operate machine during an electrical storm. If an electrical storm should strike during operation, re- main in the cab. Do not leave the cab or operator’s plat- If you are on the ground during an electrical storm, stay form.
Page 34 2 - SAFETY INFORMATION Air-conditioning system • The air-conditioning system is under high pressure. Do mosphere. Do not attempt to service or repair the sys- not disconnect any lines. The release of high pressure tem. can cause serious injury. • Only trained service technicians can service, repair, •...
Page 35: Safety Rules - Utility Precautions
2 - SAFETY INFORMATION Safety rules - Utility precautions Call all utility companies before you perform YOU MUST FOLLOW safety precautions when you work near buried utility lines. any machine operation During operation, it is likely that you will be working After you locate any buried utility lines, carefully dig a hole around or near buried utility lines that may include, but to the utility line by hand and/or with automatic vacuum...
Page 36: Safety Rules - Fuel Handling Precautions
2 - SAFETY INFORMATION Safety rules - Fuel handling precautions • Do not smoke or permit open flames while fueling or • Tighten the fuel tank cap securely. Should the fuel near fueling operations. cap be lost, replace it only with the original manufac- turer's approved cap.
Page 37: Safety Rules - Specific Precautions To This Machine
2 - SAFETY INFORMATION Safety rules - Specific precautions to this machine • From the operator's platform, install the backhoe swing • Always use the lift arm support strut when servicing the lock pin when the backhoe is not in use and before all machine with lift arms up.
Page 38: Support Strut For Loader Lift Arm
2 - SAFETY INFORMATION Support strut for loader lift arm WARNING Crushing hazard! If you service the machine with the loader lift arms raised, always use the support strut. Remove the retaining pin and place the support strut onto the cylinder rod. Install the retaining pin into the support strut.
Page 39 2 - SAFETY INFORMATION 4. Remove the strut (3) from the attachment and install the pin (1) and the split pin (2) back into the holes in the strut. 5. Start the engine and lower the loader attachment. MOLI12LBB0263AB 2-15...
Page 40 2 - SAFETY INFORMATION Machines with the Tool Carrier (TC) option Engage the loader arm support strut: 1. Remove the split pins (1) and the safety strut (2) from the storage position on the loader arm. Put the split pins back in place. 2.
Page 41: Safety Rules - Ductile Iron
2 - SAFETY INFORMATION Safety rules - Ductile iron DANGER Altering cast ductile iron can cause it to weaken or break. Before you weld, cut, or drill holes on any part of this machine, make sure that the part is not cast ductile iron.
Page 42: Hand Signals
2 - SAFETY INFORMATION Hand signals When operating the machine, never attempt to carry out tasks calling for fine control or to work in areas where visibility is poor or impaired without seeking the assistance of a signal person. Make perfectly sure that you and the signal person understand the signals to be used.
Page 43 2 - SAFETY INFORMATION Move away from me Wave hands back and forth (palms outward). LEEN11T0008AA Go this far LEEN11T0009AA All stop and hold LEEN11T0010AA Stop Move one hand back and forth. LEEN12T0534AA 2-19...
Page 44 2 - SAFETY INFORMATION Emergency stop Move both hands back and forth. LEEN11T0012AA Raise load or bucket LEEN11T0013AA Lower load or bucket LEEN11T0014AA Raise load or bucket slowly LEEN11T0015AA 2-20...
Page 45 2 - SAFETY INFORMATION Lower load or bucket slowly LEEN11T0016AA Turn machine left swing load left To stop movement, stop moving hand and make a fist. LEEN11T0017AA Turn machine right swing load right To stop movement, stop moving hand and make a fist LEEN11T0018AA Roll back loader bucket LEEN12T0535AA...
Page 46 2 - SAFETY INFORMATION Dump loader bucket LEEN12T0536AA Raise backhoe boom LEEN11T0019AA Lower backhoe boom LEEN11T0020AA Backhoe dipper in LEEN11T0021AA 2-22...
Page 47 2 - SAFETY INFORMATION Backhoe dipper out LEEN11T0022AA Backhoe bucket dig LEEN11T0023AA Backhoe bucket dump LEEN11T0024AA Retract telescopic dipper (if fitted) LEEN12T0537AA 2-23...
Page 48 2 - SAFETY INFORMATION Extend telescopic dipper (if fitted) LEEN12T0538AA 2-24...
Page 49: Ecology And The Environment
CONSTRUCTION strongly recommends that you return ble to your country, and make sure that you understand all used batteries to a NEW HOLLAND CONSTRUCTION this legislation. Where no legislation exists, obtain in- dealer, who will dispose of the used batteries or recycle formation from suppliers of oils, filters, batteries, fuels, the used batteries properly.
Page 50: Safety Signs
2 - SAFETY INFORMATION Safety signs WARNING Avoid injury! Make sure safety signs are legible. Clean safety signs regularly. Replace all damaged, missing, painted over, or illegible safety signs. See your dealer for replacement safety signs. If a safety sign is on a part that is replaced, make sure the new part has a safety sign.
Page 51 2 - SAFETY INFORMATION Safety sign locations RAIL15TLB0251HA When replacing safety signs, be sure to install them in the locations shown. Detailed description of the safety signs given below: 2-27...
Page 52 2 - SAFETY INFORMATION NOTE: Safety signs 1 through 5 are viewed from the op- erator’s seat. (1) Seat belt This safety sign can be located in the cab. Part numbers: English: 85821920 French Canadian: 85828063 Latin American Spanish: 85828064 WARNING Crush hazard! Do not jump if machine tips.
Page 53 2 - SAFETY INFORMATION (2) Safety instructions This safety sign can be located in the cab. Part numbers: English: 85821923 French Canadian: 85828065 Latin American Spanish: 85828066 WARNING Misuse hazard! • Read Operator’s Manual. • Fasten seat belt. • No riders. •...
Page 54 2 - SAFETY INFORMATION (3) Torque converter transmission (only on power shuttle models) This operational instruction sign can be located in the cab on left-hand side. Part numbers: English: 47562801 TORQUE CONVERTER TRANSMISSION WITH CLUTCH DISCONNECT BEFORE STARTING – Place both shuttle (power revers- ing) and gear shift lever in neutral and assure parking brake is applied.
Page 55 2 - SAFETY INFORMATION (5) Unexpected machine movement This safety sign can be located on the backhoe control lever in the cab. Part numbers: English: 87305413 French Canadian: 85828092 Latin American Spanish: 85828093 WARNING Unexpected movement hazard! Machine equipped with two backhoe control patterns. Be- fore operating verify desired control pattern selected for use.
Page 56 2 - SAFETY INFORMATION (7) Tie-down and lift points This safety sign can be located on the left front, rear left, rear right and right front sides of the machine (See Image Part numbers: Pictorial: 86500514 This safety sign shows the tie-down and lift points to be used when securing the machine for transport or lifting.
Page 57 2 - SAFETY INFORMATION (9) Battery This safety sign can be located on the battery cover on the right front side of the machine (See Image 1) Part numbers: English: 85821917 French Canadian: 85828088 Latin American Spanish: 85828089 DANGER Run over hazard! Read procedures in Operator’s Manual before jump start 85821917_A2 or service to avoid injury.
Page 58 2 - SAFETY INFORMATION (11) Hydraulic oil tank This safety sign can be located on the hydraulic tank on the right hand side of the machine (See Image 1) Part numbers: Pictorial: 85804341 Make sure that you only fill a reservoir bearing this safety sign with hydraulic fluid.
Page 59 2 - SAFETY INFORMATION (14) Starting the engine This safety sign can be located on the right-hand side loader support (See Image 1) Part numbers: English: 85821918 French Canadian: 85828086 Latin American Spanish: 85828087 DANGER Runover hazard! Start engine only from operator’s seat with transmission in NEUTRAL.
Page 60 2 - SAFETY INFORMATION (15) Backhoe attachment This safety sign can be located on the right-hand side loader support (See Image 1) Part numbers: English: 85821922 French Canadian: 85828080 Latin American Spanish: 85828081 DANGER Crush hazard! Keep clear Swinging boom can KILL or Seriously injure. Do not enter the platform from the rear.
Page 61 2 - SAFETY INFORMATION (16) Precautions for lifting loads This safety sign can be located on the left side of the back- hoe boom (See Image 1) Part numbers: English: 85821924 French Canadian: 85828069 Latin American Spanish: 85828070 WARNING Rollover Crush hazard! Lifting too heavy a load can cause machine roll over or loss of operator control.
Page 62 2 - SAFETY INFORMATION (18) Air-conditioning (Optional) This safety sign can be located on the left front side of the machine (See Image 1) Part numbers: Pictorial: 85804441 This safety sign indicates that an air-conditioning system is installed in the machine. The maintenance operations must be performed by qualified personnel.
Page 63 2 - SAFETY INFORMATION (20) Do not use ether This safety sign can be located on the right-hand side of the engine compartment (See Image 1) Part numbers: English: 8603092 French Canadian: 8603093 Latin American Spanish: 8603094 WARNING Explosion hazard! Do not use ether.
Page 64 2 - SAFETY INFORMATION (22) Support loader lift arms This safety sign can be located on the right-hand loader lift arm (See Image 1) Part numbers: English: 85821946 French Canadian: 85828082 Latin American Spanish: 85828083 WARNING Crush hazard! Keep clear. LEEN12T0738AA Support loader lift arms during maintenance or repair.
Page 65: Selective Catalytic Reduction (Scr) Decals
2 - SAFETY INFORMATION Selective Catalytic Reduction (SCR) decals Only fill the DEF/AdBlue® tank with approved DEF/AdBlue® solution. Do not fill with diesel fuel or water. Refer to the Operator's Manual. Quantity: 1 English 84284896 84284896_C Location: Near the DEF/AdBlue® fill cap. RAIL15TLB0021AA Only use Ultra Low Sulfur Diesel (ULSD) fuel.
Page 66 2 - SAFETY INFORMATION 2-42...
Page 67: Controls And Instruments
3 - CONTROLS AND INSTRUMENTS 3 - CONTROLS AND INSTRUMENTS###_3_### ACCESS TO OPERATOR'S PLATFORM Access to operator’s platform CAUTION Fall hazard! When entering or exiting the cab, never use the control levers as handholds. Always mount and dis- mount the machine in a safe way. Maintain a three-point contact with steps, ladders, and/or handholds. Failure to comply could result in minor or moderate injury.
Page 68 3 - CONTROLS AND INSTRUMENTS Cab door window Partially opened Raise the handle (1) and push it outwards and downwards to lock the window in a partially opened position. Fully opened With the window closed, raise the handle (1) to the hor- izontal position and then tilt it rearwards to disengage it from the pin.
Page 69 3 - CONTROLS AND INSTRUMENTS Rear window Opening the rear window 1. Release the rear window pin locks (1). One on each side. 2. Swing the bottom of the window outwards with the both handles (2). 3. Bring the window into horizontal position and lock the window in position with the latches (3).
Page 70: Operator's Seat
3 - CONTROLS AND INSTRUMENTS OPERATOR'S SEAT Operator's seat To operate the machine correctly with maximum efficiency and comfort, check that the operator’s seat and its adjust- ment controls are in good condition and then adjust the seat to suit the operator’s size and weight. CAUTION Avoid injury! Before operating the machine, and whenever...
Page 71 3 - CONTROLS AND INSTRUMENTS Seat back angle adjustment Adjust the seat back angle. Pull and hold the lever (1) upward, tilt the seat back to obtain the desired position and then release the lever. Swing Lift the lever (2) to rotate the seat between the normal driving/loader operating position and the backhoe operat- ing position.
Page 72 3 - CONTROLS AND INSTRUMENTS Deluxe seat – pneumatic suspension with heated seat Seat belt Pull and insert the buckle (4) into the socket (3). Press the button (2) on the socket (3) to release the buckle. Guide the buckle back into position. Armrest angle adjustment Rotate the knob (1) to set the armrest position incline when in a down position.
Page 73 3 - CONTROLS AND INSTRUMENTS Heated seat switch Press the emblem side of the switch (1) to turn on the heat function. Press the “0” side of the switch to turn off the heat function. Lumbar adjustment Turn the knob (2) to adjust the lumbar back. Seat back angle adjustment Adjust the seat back angle.
Page 74 3 - CONTROLS AND INSTRUMENTS Backrest support extension Lift up on the backrest extension (1) to the desired posi- tion. Use tab (2) on posts to lower the backrest extension. RAIL18TLB0200BA...
Page 75: Forward Controls
NOTICE: If the steering hose broke and the machine could not be steered, stop the machine immediately. Contact your NEW HOLLAND CONSTRUCTION Dealer for further assistance. LEEN11T0038AA In the event of loss of power steering due to engine failure, the machine can still be driven to a place of safety.
Page 76: Front Controls
3 - CONTROLS AND INSTRUMENTS Front controls LEEN11T0010FA (1) Four-Wheel Drive (4WD) switch (optional) Two function switch: • Power shuttle machines, – Press the blank side to switch for rear wheel drive and braking on rear wheels (for all gears) (control lamp off). •...
Page 77 3 - CONTROLS AND INSTRUMENTS (5) Rotating beacon switch This switch has two positions: 1. Press the emblem to turn ON the beacon (control lamp off). 2. Press the blank side to turn OFF the beacon (control lamp off). (6) Blank (7) Blank (8) Auto or manual shift (optional) - Powershift machines only Three position switch...
Page 78: Right-Hand Side Control Lever
3 - CONTROLS AND INSTRUMENTS Right-hand side control lever Lever for direction indicators, main beams, front windshield wiper and washer (cab) Located on the right of the steering wheel, this lever has five positions: Position 0: Neutral. Position 1: The left-hand direction indicators and the di- rection indicator lamp on the side instrument cluster flash at the same speed.
Page 79: Pedal Controls
3 - CONTROLS AND INSTRUMENTS Pedal controls Foot throttle The foot throttle (1) is under the steering wheel. Use the foot throttle to increase or decrease engine speed when traveling. Use the foot throttle to increase or decrease power for loader operations. •...
Page 80: Transmission Controls
3 - CONTROLS AND INSTRUMENTS Transmission controls WARNING Loss of control hazard! To prevent inadvertent machine movement, take care to avoid accidental contact with the gearshift levers. Always stop the engine, firmly apply the parking brake, and place all gearshift levers in neutral before leaving the machine.
Page 81 3 - CONTROLS AND INSTRUMENTS Manual transmission The transmission is fully synchronized providing four forward and four reverse speeds allowing gear ratio changes on the move. A torque converter is used to connect the engine to the transmission and the direction control lever (3) enables shifts between forward and reverse travel without disengaging gear ratios.
Page 82 3 - CONTROLS AND INSTRUMENTS Transmission disconnect button WARNING Loss of control hazard! Machines with four-wheel drive engaged or disengaged should not exceed 50 km/h (31 mph) where permitted. Over speeding by towing or coasting downhill with clutch de- pressed or transmission in neutral may cause loss of control, personal injury to the operator or bystanders, or mechanical failure.
Page 83 3 - CONTROLS AND INSTRUMENTS To make upward gear ratio changes 1. Press and hold the button (2) on the gearshift lever (1) while moving the lever from a lower gear to a higher gear. 2. Release the button and allow the unit to gain engine speed and ground speed.
Page 84 3 - CONTROLS AND INSTRUMENTS Powershift transmission controls (optional) RAIL18TLB0067FA (1) Powershift transmission gearshift and direction control lever: This lever controls machine direction and gear selection. (2) Kickdown control: The kickdown control allows the operator to temporarily switch from second gear to first gear, without changing the gear selection control setting.
Page 85 3 - CONTROLS AND INSTRUMENTS Powershift transmission On powershift transmissions the gear selection control is on the direction control lever on the left-hand side of the steering wheel. Direction control lever NOTE: Stop the machine from moving before switching between FORWARD and REVERSE travel. The direction control lever is on the left-hand side of the steering column and controls the direction of travel for the machine.
Page 86 3 - CONTROLS AND INSTRUMENTS Kickdown control NOTE: Only available on machines with the optional Pow- ershift transmissions. NOTE: This feature will only activate when in second gear. Kickdown is used to increase the loader breakout force. The kickdown control lets the operator temporarily switch from second gear to first gear, without changing the gear selection control setting.
Page 87: Right-Hand Side Controls
3 - CONTROLS AND INSTRUMENTS RIGHT-HAND SIDE CONTROLS Key start switch NOTE: The instruments represented may not exactly correspond to the instruments on your machine. Starter switch key WARNING Misuse hazard! Before starting the engine, make sure you are fully aware of the location and the function of each control.
Page 88: Instrument Cluster Panel - Side
3 - CONTROLS AND INSTRUMENTS Instrument cluster panel – Side LEEN11T0021FA (1) Front work lights Front work light switch: This switch has three positions: • The first position is OFF (control lamp off). • Second position, by pressing the symbol side (first click) the outer front work lights are turned on (control lamp on).
Page 89 3 - CONTROLS AND INSTRUMENTS (3)Glide Ride™ switch (optional on 2WD models) or Auto-Glide Ride™ switch (Optional on 4WD models) Glide Ride™ The Glide Ride™ system control improves the machine comfort during travel, regardless of a full or empty bucket over any type of terrain. It reduces forward and rearward pitching when moving rearwards or forwards and when carrying loads, at the same time increasing productivity and operator comfort.
Page 90 3 - CONTROLS AND INSTRUMENTS (9) Rear windshield wiper and washer switch (cab only) Rear windshield wiper and washer switch: This switch has three positions: • Press the switch to activate the windshield wiper. • Press and hold the switch will activate the windshield washer. Release the switch the washer stops and the wiper operates.
Page 91: Exterior Controls
3 - CONTROLS AND INSTRUMENTS EXTERIOR CONTROLS Rotating beacon (Optional) The rotating beacon (1) should be placed on the cab roof and the cable connected to one of the 12 V sockets over the door on each side of the machine. NOTICE: The rotating beacon must be installed and op- erated when undertaking road travel LEEN11T0081AA...
Page 92: Battery Master Switch
3 - CONTROLS AND INSTRUMENTS Battery master switch NOTICE: Wait at least 60 s after you place the ignition key in the OFF position before turning master disconnect switch to OFF. This allows the machine controllers to shut down properly. NOTE: The battery master switch must be switched off at the end of each working day, for machine service or for any operations on the electrical system.
Page 93: Instrument Cluster
3 - CONTROLS AND INSTRUMENTS INSTRUMENT CLUSTER Instrument cluster The vehicle controller, engine controller, and electronic transmission controller, if equipped, on the machine monitors machine functions and controls. The control modules also activate warning lamps and audible alarms and display information on the AIC display.
Page 94 3 - CONTROLS AND INSTRUMENTS Direction (turn signal or hazard) Indicator lamp. Illuminates when the turn signals or hazard lights are ON RAIL19TLB0004AA Low engine oil pressure Warning lamp. Illuminates when, with the engine running, there is no or low oil pressure in the engine.
Page 95 3 - CONTROLS AND INSTRUMENTS Alternator Warning lamp. Illuminates when, with the engine running, the alternator is not charging the battery. RAIL19TLB0004AA Parking brake Indicator lamp. Illuminates when the parking brake is set. RAIL19TLB0004AA Air filter restriction Warning lamp. Illuminates and a one second audible alarm sounds when, with the engine running, the air filter element is restricted and requires service.
Page 96 3 - CONTROLS AND INSTRUMENTS Engine glow plugs Indicator lamp. Illuminates when, with the key switch in the ON position, the engine glow plugs are active due to cold temperatures. Wait until the lamp goes off before turning the key switch to the START position. RAIL19TLB0004AA Low fuel level Warning lamp.
Page 97 3 - CONTROLS AND INSTRUMENTS Tachometer Shows the engine speed in Revolutions Per Minute (RPM). Each tick mark on the gauge is equal to 100 RPM. It is recommended that the engine be run in the green area of the gauge. NOTE: Above the top of the tachometer is a guide for traveling speeds.
Page 98: Menu Screen Display
3 - CONTROLS AND INSTRUMENTS Menu screen display Display screen Display screen In addition to the indicator/warning lamps, the Advanced Instrument Cluster (AIC) displays information on the dis- play screen. The next few pages describe the standard menu screens that are used to program machine func- tionality, perform diagnostics, and troubleshooting.
Page 99 3 - CONTROLS AND INSTRUMENTS Forward-Neutral-Reverse (F-N-R) sensitivity NOTE: Machines with the optional Powershift transmis- sion only. The factory default setting is 2. Increase or decrease the sensitivity setting for shifting between Forward-Neutral-Reverse, 1 is least aggressive and 3 is most aggressive. NOTE: See “Forward-Neutral-Reverse (F-N-R) shift sen- sitivity”...
Page 100 3 - CONTROLS AND INSTRUMENTS Maximum throttle/cold start idle Access the Idle Increment screen to adjust the cold start idle and maximum throttle values for special operating conditions. NOTE: See “Maximum throttle/Cold start idle” 6-3 for more details. RCPH10TLB201AAF Machine hardware Displays machine hardware information.
Page 101 3 - CONTROLS AND INSTRUMENTS Throttle sensitivity Select the sensitivity level for the electronic foot throttle, 1 is least aggressive and 3 is most aggressive. Operators may change the electronic throttle sensitivity for working conditions or personal preference. NOTE: See “Throttle sensitivity” 6-5 for more details. RCPH10TLB195AAF Auto engine shutdown time-out The auto engine shutdown feature allows the operator to...
Page 102 3 - CONTROLS AND INSTRUMENTS Auto-Glide Ride™ (ARC) speed threshold; if equipped: Three factory preset speed thresholds available. Speeds are approximate depending on tire size, model, and transmission type: • Setting 1 — Ride control activates when the machine is moving faster than 9.2 km/h (5.7 mph) and deactivates when the machine is travelling slower than 7.6 km/h (4.7 mph).
Page 103: Selective Catalytic Reduction (Scr) Exhaust Treatment - Overview
Your NEW HOLLAND CONSTRUCTION machine is equipped with a warning system to inform the operator of the DEF/AdBlue® level, system malfunctions, and engine power loss that may result from the SCR system for reducing exhaust emissions.
Page 104 3 - CONTROLS AND INSTRUMENTS Display Description Warning lamps and Corrective action alarms DEF/AdBlue® level is empty. Fill DEF/AdBlue® tank Severe torque reduction and immediately. Cycle the key engine speed reduction will switch (or the POWER button) occur. OFF then ON. Continuous alarm and the DEF gauge indicator is on empty..
Page 105 3 - CONTROLS AND INSTRUMENTS DEF/AdBlue® level faults, failures, and engine power loss levels NHPH14ENG0567HA 3-39...
Page 106 3 - CONTROLS AND INSTRUMENTS DEF/AdBlue® quality faults, failures, and engine power loss levels NHPH14ENG0693HA 3-40...
Page 107 If you attempt a third restart, the engine will be locked at 50% torque and engine idle. Contact your NEW HOLLAND CONSTRUCTION dealer to reset the engine restart counter and resolve the fault causing the loss of productivity.
Page 108 3 - CONTROLS AND INSTRUMENTS 3-42...
Page 109 3 - CONTROLS AND INSTRUMENTS NHPH14ENG0694JA 3-43...
Page 110 3 - CONTROLS AND INSTRUMENTS NHPH14ENG0566JA 3-44...
Page 111 If all three validation re-starts have been used and the system has not been reset, the machine is limited to 50% torque and engine idle only. See your local authorized NEW HOLLAND CONSTRUCTION dealer for repair. Follow the sequence in figure 6 to activate validation re-starts.
Page 112 3 - CONTROLS AND INSTRUMENTS NHPH14ENG0568HA 3-46...
Page 113 • If the same failure is detected three consecutive times within 40 h of engine operation, maximum engine power loss will remain active after engine restart until the system is repaired. • Please contact your authorized NEW HOLLAND CONSTRUCTION dealer for service. 3-47...
Page 114: Cab Controls And Adjustments
3 - CONTROLS AND INSTRUMENTS CAB CONTROLS AND ADJUSTMENTS Cab and platform - Control identification Operator’s manual storage In the rear part of the operator’s seat there is a docu- ment storage box (1) where the Operator’s Manual can be stored. LEEN11T0064AA Document storage box Under the cab roof there is a document storage box (1)
Page 115 3 - CONTROLS AND INSTRUMENTS Sun visor Use the tab (1) to pull the sun visor down and place it in the position required. Push up the latch (2) to roll up the sun visor. LEEN11T0066AA Auxiliary 12 V socket An auxiliary 12 V power socket (1) is located on the cab’s left-hand post.
Page 116 3 - CONTROLS AND INSTRUMENTS Object storage box Located on the left-hand side of the cab. This compart- ment (1) is intended for storing objects of various types. LEEN11T0070AA Front and rear windshield washer reservoir This reservoir (1) is located on the left-hand side of the cab and has two electric pumps controlled by a switch or by the lever for the direction indicators, main beams, front windshield wiper and washer.
Page 117 3 - CONTROLS AND INSTRUMENTS Engine guard handle WARNING Crushing hazard! Always install the safety lock before working under the raised attachment. Failure to comply could result in death or se- rious injury. W1448A Open the engine hood: 1. Insert the key (1) and turn counter-clockwise. 2.
Page 118 3 - CONTROLS AND INSTRUMENTS Coat hanger hook The hook (1) fitted on the left-hand cab upright, allows the hanging of possible clothes. LEEN11T0073AA Air filter The air filter is located under the operator’s seat. See 7-73 for the maintenance procedure. RAIL15TLB0610BA Fire extinguisher DANGER...
Page 119 3 - CONTROLS AND INSTRUMENTS Fuse and relay control unit The fuse and relay control unit is located under the side instrument cluster panel and may be accessed via the right-hand cab door. The diagnostic socket is located to the left of the fuse and relay control unit.
Page 120: Loader Attachment Controls
3 - CONTROLS AND INSTRUMENTS LOADER ATTACHMENT CONTROLS Loader attachment control lever (1) Loader control lever: Controls the loader attachment movement. See “Loader attachment controls” 3-55 for more details. (2) Bucket control, 4-in-1 bucket only: Roll the switch upward to open the bucket (1). Release the switch to stop.
Page 121: Loader Attachment Controls
3 - CONTROLS AND INSTRUMENTS Loader attachment controls WARNING Misuse hazard! Before starting the engine, make sure you are fully aware of the location and the function of each control. Failure to comply could result in death or se- rious injury. W0226A WARNING Avoid injury!
Page 122: Loader Attachment - Operation
3 - CONTROLS AND INSTRUMENTS Loader attachment – Operation Neutral and hold With the lever in the neutral/hold position 0, the attach- ment movement can be stopped. As soon as the lever is released, it automatically returns to the neutral position 0 and the attachment remains in the position where it was when movement stopped.
Page 123 3 - CONTROLS AND INSTRUMENTS Loader bucket float control With the lever in position (3), the bucket follows the con- tours of the ground without it being necessary to operate the lever. NOTE: In this position the lever does not automatically return to neutral when it is released.
Page 124 3 - CONTROLS AND INSTRUMENTS Automatic return to loader bucket filling With the lever in position (6), the attachment lowers and, simultaneously, the bucket places itself to the digging po- sition. NOTE: It is possible to adjust the tilt angle for bucket filling. MOLI12LBB0163AB 3-58...
Page 125: Detent Position For Loader Control Auxiliary Hydraulics
NOTE: See the attachment manufacturers user guide for operating details. Contact your NEW HOLLAND CON- STRUCTION dealer for a list of approved attachments.
Page 126 3 - CONTROLS AND INSTRUMENTS 6. Test the detent operation: A. Push the switch up. The switch should hold in place (not spring back to center), as shown. B. Pull the switch out of the detent position. 7. Replace the cap that covers the screw. NOTE: Take the machine to an open, safe area and test the switch by moving it through the entire range of motion in both directions.
Page 127: Backhoe Attachment Controls
3 - CONTROLS AND INSTRUMENTS BACKHOE ATTACHMENT CONTROLS Remove the backhoe from the stowed position WARNING Unexpected machine movement! Before you use the backhoe attachment, make sure that the machine is resting on the stabilizers. Failure to comply could result in death or serious injury. W1326A WARNING Unexpected machine movement!
Page 128 3 - CONTROLS AND INSTRUMENTS Removing the backhoe from the stowed position (mechanical) 1. Start the machine. 2. Place the direction control lever in NEUTRAL position. 3. If applicable, place gearshift control lever in the NEU- TRAL position. 4. Turn the seat into the backhoe operation position. 5.
Page 129 3 - CONTROLS AND INSTRUMENTS Move the boom all the way towards you to relieve pressure on the boom lock (2). Press the button on the boom lock control lever (1) and move forward to disengage the boom lock. 10. Lower the boom. RAIL15TLB0050AA RAIL15TLB0051AA 11.
Page 130 3 - CONTROLS AND INSTRUMENTS Removing the backhoe from the stowed position (hydraulically, if equipped) 1. Start the machine. 2. Place the direction control lever in NEUTRAL position. 3. If applicable, place gearshift control lever in the NEU- TRAL position. 4.
Page 131 3 - CONTROLS AND INSTRUMENTS 8. Place the switch (1) in the OFF position to disengage the hydraulic boom lock (2) . The indicator lamp (3) (mechanical backhoe models) or the indicator lamp (4) (pilot backhoe models) turns OFF. 9. Lower the boom. LEEN11T0311AA RAIL15TLB0547BA MOLI12LBB0249AB...
Page 132 3 - CONTROLS AND INSTRUMENTS 10. If applicable, remove the extendable dipper lock pin (1) and place it in the storage position (2). RAIL15TLB0545BA 3-66...
Page 133: Place The Backhoe In The Stowed Position
3 - CONTROLS AND INSTRUMENTS Place the backhoe in the stowed position WARNING Unexpected machine movement! Before you use the backhoe attachment, make sure that the machine is resting on the stabilizers. Failure to comply could result in death or serious injury. W1326A WARNING Unexpected machine movement!
Page 134 3 - CONTROLS AND INSTRUMENTS Placing the backhoe in the stowed position (mechanical) 1. Start the machine. 2. Place the direction control lever in NEUTRAL position. 3. If applicable, place gearshift control lever in the NEU- TRAL position. 4. Turn the seat into the backhoe operation position. 5.
Page 135 3 - CONTROLS AND INSTRUMENTS 11. If applicable, open the rear window. 12. Remove the swing lock pin from the storage location. 13. From the operator’s seat, place the swing lock pin in the lock position. RAIL16TLB1504BA RAIL16TLB1340BA 14. Raise the stabilizers. 3-69...
Page 136 3 - CONTROLS AND INSTRUMENTS Placing the backhoe in the stowed position (hydraulically, if equipped) 1. Start the machine. 2. Place the direction control lever in NEUTRAL position. 3. If applicable, place gearshift control lever in the NEU- TRAL position. 4.
Page 137 3 - CONTROLS AND INSTRUMENTS Raise the boom 10. Place the switch (1) in the ON position to engage the hydraulic boom lock (2) . The indicator lamp (3) (mechanical backhoe models) or the indicator lamp (4) (pilot backhoe models) turns ON. LEEN11T0311AA RAIL15TLB0547BA MOLI12LBB0249AB...
Page 138 3 - CONTROLS AND INSTRUMENTS 11. If applicable, open the rear window. 12. Remove the swing lock pin from the storage location. 13. From the operator’s seat, place the swing lock pin in the lock position. RAIL16TLB1504BA RAIL16TLB1340BA 14. Raise the stabilizers. 3-72...
Page 139: Backhoe Attachment Mechanical Controls Version
3 - CONTROLS AND INSTRUMENTS Backhoe attachment mechanical controls version Stabilizer mechanical controls WARNING Unexpected machine movement! Before you use the backhoe attachment, make sure that the machine is resting on the stabilizers. Failure to comply could result in death or serious injury. W1326A Left-hand stabilizer control lever This lever (A) has three positions:...
Page 140 3 - CONTROLS AND INSTRUMENTS Standard configuration Left-hand control lever (boom and swing control) This lever has five positions and is equipped with a horn button (J): Position “0”: Neutral/hold. This position enables the at- tachment movement to be stopped. As soon as the lever is released, it automatically returns to the neutral position “0”...
Page 141 3 - CONTROLS AND INSTRUMENTS LEEN12T0557HA_1 Standard configuration 3-75...
Page 142 3 - CONTROLS AND INSTRUMENTS ISO configuration Left-hand control lever (dipper and bucket/ attachment control) This lever has five positions and is equipped with a horn button (J): Position “0”: Neutral/hold. This position enables the at- tachment movement to be stopped. As soon as the lever is released, it automatically returns to the neutral position “0”...
Page 143 3 - CONTROLS AND INSTRUMENTS LEEN12T0558HA_1 ISO configuration 3-77...
Page 144 3 - CONTROLS AND INSTRUMENTS Four-lever pattern configuration Lever (1) for dipper Lever (3) for backhoe bucket This lever has three positions and is equipped with a This lever has three positions: horn button (J): Position “0”: Neutral/hold. This position enables the Position “0”: Neutral/hold.
Page 145 3 - CONTROLS AND INSTRUMENTS LEEN12T0559GA_1 Four-lever pattern configuration 3-79...
Page 146 3 - CONTROLS AND INSTRUMENTS Cross-pattern configuration Left-hand control lever (boom and swing control) This lever has five positions and is equipped with a horn button (J): Position “0”: Neutral/hold. This position enables the at- tachment movement to be stopped. As soon as the lever is released, it automatically returns to the neutral position “0”...
Page 147 3 - CONTROLS AND INSTRUMENTS LEEN12T0560HA_1 Cross-pattern configuration 3-81...
Page 148 3 - CONTROLS AND INSTRUMENTS Telescopic dipper mechanical control pedal (if fitted) NOTE: Make sure that the telescopic dipper lock pin is in the storage position. This pedal (A) has three positions: Position “0”: Neutral. This position enables the movement of the telescopic dipper to be stopped.
Page 149: Backhoe Attachment Hydraulic Controls
3 - CONTROLS AND INSTRUMENTS Backhoe attachment hydraulic controls MOLI12LBB0178FB Control enable switch: With this switch in the ON dipper. Press the left-hand button to retract the (lamp on) position, all backhoe attachment hydraulic telescopic dipper. controls are functional. Wrist rests: The wrist rests may be adjusted to the Left-hand hydraulic control lever: The left-hand hy- required height.
Page 150 3 - CONTROLS AND INSTRUMENTS Control enable switch This control is located on the right-hand control lever. This switch has three positions: • Position OFF: (Lamp off) all controls will deactivate. • Position “1”: By pressing the upper side (lamp off), the stabilizers will activate.
Page 151 3 - CONTROLS AND INSTRUMENTS Backhoe attachment hydraulic controls Standard configuration Backhoe boom and backhoe attachment swing left-hand hydraulic control lever. This hydraulic control lever has five positions: Position “0”: Neutral/hold. This position enables the at- tachment movement to be stopped. As soon as the hy- draulic control lever is released, it automatically returns to the neutral position “0”...
Page 152 3 - CONTROLS AND INSTRUMENTS Stabilizer hydraulic controls WARNING Unexpected machine movement! Before you use the backhoe attachment, make sure that the machine is resting on the stabi- lizers. Failure to comply could result in death or se- rious injury. W1326A These controls are located on the left-hand hydraulic con- trol lever and may be operated independently or simulta-...
Page 153 3 - CONTROLS AND INSTRUMENTS Auto-up feature (Optional) Position “3”: When the levers are momentarily pulled back to this position and then released, they return to the neu- tral position and the stabilizers automatically rise to road travel position, there by leaving your hand free for other duties.
Page 154 3 - CONTROLS AND INSTRUMENTS Auxiliary uni-directional controls (If fitted) Press and hold the left-hand proportional button (1) to ac- tivate the attachment hydraulic oil flow. NOTE: The left-hand proportional button (2) is inoperable with Uni-driectional option. MOLI12LBB0187AB Auxiliary bi-directional controls (If fitted) Press and hold the left-hand button (1) to let the oil flow out of the left-hand side of the boom.
Page 155: Climate Controls
3 - CONTROLS AND INSTRUMENTS CLIMATE CONTROLS Heating and air-conditioning controls The Heating, Ventilation, and Air-Conditioning (HVAC) controls are located on the right-hand side of the cab (opera- tor’s seat in loader attachment position). Ventilation controls NOTE: The fan control knob circulates the air inside the cab and does not heat or cool the cab air.
Page 156 3 - CONTROLS AND INSTRUMENTS Heating Heater coolant shutoff valve The heater coolant shutoff valve controls the flow of hot coolant to the heater. • In warm ambient temperatures, turn the shutoff valve (1) clockwise to stop hot coolant flow to the heater. •...
Page 157 3 - CONTROLS AND INSTRUMENTS Air-Conditioning system (Optional) WARNING Explosion hazard! Air-conditioning refrigerant boils at -12 °C (10 °F)! -NEVER expose any part of the air-conditioning system to a direct flame or excessive heat. -NEVER disconnect or disassemble any part of the air-conditioning system. Discharging refrigerant gas into the atmosphere is illegal in many countries.
Page 158 3 - CONTROLS AND INSTRUMENTS Climate controls with Air-Conditioning (A/C) (optional) Activate the Air-Conditioning system: 1. Start the machine. 2. Turn the fan control knob (3) to one of the three fan speed settings. 3. Turn the A/C ON/OFF switch t (2) o the ON position. NOTE: The A/C symbol (4) on the instrument cluster will illuminate when the A/C is On.
Page 159: Cab Air Louvers
3 - CONTROLS AND INSTRUMENTS Cab air louvers Air flow diffusers are connected to the heater system and receive air from the blower, to direct warm or cold air onto the windshield and side windows or to the cab interior as required.
Page 160 3 - CONTROLS AND INSTRUMENTS 3-94...
Page 161: Operating Instructions
4 - OPERATING INSTRUCTIONS 4 - OPERATING INSTRUCTIONS###_4_### COMMISSIONING THE UNIT Before using the machine NOTICE: Read and familiarize yourself with the instruc- Make sure that the safety signs are always clean. tions and warnings shown in this manual before operating Clean or replace safety signs which are no longer legible.
Page 162: Operating The Machine
4 - OPERATING INSTRUCTIONS Operating the machine WARNING Before carrying out any road travel, lock the attachments and install the safety systems required by regulations. Driving hazard! Check all controls and safety devices in a safe, The machine must be within the maximum dimensions open area before starting work.
Page 163 4 - OPERATING INSTRUCTIONS NOTICE: Electrical cables, gas pipes, water pipes or Do not work close to live overhead electric lines with- other underground installations can cause serious physi- out first making sure that the minimum distances are ob- cal injury. served: 5 m (16.4 ft).
Page 164: Run In Period Of A New Machine
“Initial 20 hours”. If any abnormalities are found contact your NEW HOLLAND CONSTRUCTION dealer immediately. After the first 50 operating hours After the first 50 operating hours, consult your NEW HOLLAND CONSTRUCTION dealer for the 50 h maintenance interval.
Page 165: Starting The Unit
4 - OPERATING INSTRUCTIONS STARTING THE UNIT Before starting the engine WARNING Inhalation/asphyxiation hazard! Make sure there is proper ventilation before starting the engine. Failure to comply could result in death or serious injury. W0091A WARNING Hazard to bystanders! Before you start the engine, make sure that the area surrounding the machine is clear of all persons, and that the backhoe swing lock pin is in the LOCK position.
Page 166: Normal Engine Starting
4 - OPERATING INSTRUCTIONS Normal engine starting NOTICE: If the engine does not start within 30 s, allow the starter to cool for one minute and then begin the procedure again. 1. Adjust the seat and fasten the seat belt. 2.
Page 167: Engine Speed
4 - OPERATING INSTRUCTIONS Engine speed It is recommended that you run the engine at full throttle when operating conditions permit and when safe. NOTICE: Do not run the engine at idle speed for long periods. This can cause a low operating temperature. Low operating temperature can cause acids and deposits in the engine oil.
Page 168: Cold Temperature Operation
Fuel system: • Check with your dealer for the correct cold weather fuel. In addition to the winter blend NEW HOLLAND CON- STRUCTION recommends the use of a cold weather diesel fuel additive. Follow the directions on the manufactures label.
Page 169 4 - OPERATING INSTRUCTIONS Machine start up in cold weather Machines at temperatures below -2 °C (29 °F): 1. If equipped, plug the engine block heater into an appropriate electrical outlet a few hours before starting the ma- chine. 2. Turn the key switch to the ON position and check the instrument cluster. 3.
Page 170: Hot Temperature Operation
4 - OPERATING INSTRUCTIONS Hot temperature operation Hot weather conditions cause special problems. During these conditions, your machine will require special attention to prevent serious damage. Hot weather maintenance will extend the service life of your machine. Use OAT E premix ( 50% concentrate and 50% distilled water) XTENDED OOLANT...
Page 171: Operating The Machine In High Altitude
4 - OPERATING INSTRUCTIONS Operating the machine in high altitude Air density decreases as altitude or ambient temperature increases. As a result of this, the engine’s maximum output, quality of exhaust gas, temperature level and, in extreme cases, starting behavior, are impaired. Engine can be used at altitudes up to 3000 m (9842 ft) and temperatures up to 50 °C (122 °F) for mobile opera- tions.
Page 172: Operating The Machine In Water
4 - OPERATING INSTRUCTIONS Operating the machine in water WARNING Loss of control hazard! If the machine has to be operated in water, make sure of the following: 1. The bed of the stream or stretch of water can support the weight of the machine. 2.
Page 173: Assisted Starting (Jump-Starting)
4 - OPERATING INSTRUCTIONS Assisted starting (Jump-starting) DANGER Explosion hazard and/or run over hazard! Read the procedure in the operator's manual before jump-start or service to avoid injury. Failure to comply will result in death or serious injury. D0149A WARNING Explosion hazard! If battery electrolyte is frozen, attempting to charge the battery or jump-start the engine can cause the battery to explode.
Page 174 4 - OPERATING INSTRUCTIONS Assisted starting connections Two persons are required for this procedure. Make sure the person making the connection is wearing hand and face protection. Switch off all electrical accessories in receiving ma- chine and turn key switch to “0”. Switch off all accessories in supplying machine (booster battery) and shut off engine.
Page 175: Stopping The Unit
4 - OPERATING INSTRUCTIONS STOPPING THE UNIT Shutting down the engine NOTE: After you turn off the engine you will continue to hear a clapping or clicking sound this is normal. The Selective Catalytic Reduction (SCR) system is clearing the Diesel Exhaust Fluid (DEF)/AdBlue® fluid from the tank lines. NOTICE: Wait 90 s before turning the master disconnect switch to the Off position.
Page 176: Moving The Unit
4 - OPERATING INSTRUCTIONS MOVING THE UNIT Job site travel NOTE: The instruments represented may not exactly correspond to the instruments on your machine. NOTE: After road travel, remove all road safety devices before carrying out any job site travel. 1.
Page 177 4 - OPERATING INSTRUCTIONS 9. (Power shuttle) Press the transmission disconnect button (5) and then place the gearshift lever (6) in first or second gear. LEEN11T0111AA (Powershift) Place the gearshift lever (7) in first or second gear. 10. Press the brake pedals down and lower the parking brake lever.
Page 178: Before Operating The Machine
4 - OPERATING INSTRUCTIONS Before operating the machine WARNING Equipment failure could cause accident or injury! Before operating the machine, check for correct operation of steering, brakes, hydraulic controls, instruments, and safety equipment. Make sure the transmission control lever is in the neutral position. Make all adjustments before operating the machine.
Page 179: Traveling On A Hill
4 - OPERATING INSTRUCTIONS Traveling on a hill WARNING Driving hazard! Hillside operations can be dangerous. Rain, snow, ice, loose gravel, or soft ground, etc. can change the ground conditions. You must make a judgment if it is safe to operate your machine on any hillside or ramp.
Page 180: Auto Powershift
4 - OPERATING INSTRUCTIONS Auto powershift NOTICE: Transmission disconnects when the parking brake is engaged. The transmission is synchronized in all gears. You may shift to any gear without stopping the machine. When shifting gears, always make sure the engine speed remains in the normal (green) area of the tachometer. Manual transmission Push the transmission disconnect button on the shift lever (1) before you shift gears.
Page 181 4 - OPERATING INSTRUCTIONS Auto shift mode 1. Press the emblem side of the Transmission mode se- lection switch (2) on the left-hand side of the front con- sole. 2. Select a gear on the gear selector lever (1). Use the table as a guide for the appropriate gear selection.
Page 182: Four-Wheel Drive (4Wd) Control Switch (If Equipped)
4 - OPERATING INSTRUCTIONS Four-Wheel Drive (4WD) control switch (if equipped) Machines with or without four wheel drive should not be allowed to exceed 40 km/h (24.8 mph) WARNING Loss of control hazard! Machines with four-wheel drive engaged or disengaged should not exceed 50 km/h (31 mph) where permitted.
Page 183: Differential Lock Button
4 - OPERATING INSTRUCTIONS Differential lock button NOTICE: Never use the differential lock during road travel. The differential lock gives equal power to both rear wheels. It is particularly useful when the wheels have insufficient grip, as in the following cases. When the machine is stuck Make sure that the rear wheels are not turning.
Page 184: Glide Ride™ - Two-Wheel Drive (2Wd) Only
4 - OPERATING INSTRUCTIONS Glide Ride™ - Two-Wheel Drive (2WD) only WARNING Unexpected machine movement! Stand clear of the loader arms. If you enable Glide Ride™ or Auto-Glide Ride™ control with the key switch in the ON or ACC position, the loader arms can drop slightly due to the hydraulic accumulator. Failure to comply could result in death or serious injury.
Page 185: Auto-Glide Ride™ (Agr) - Four-Wheel Drive (4Wd) Only
4 - OPERATING INSTRUCTIONS Auto-Glide Ride™ (AGR) – Four-Wheel Drive (4WD) only WARNING Unexpected machine movement! Stand clear of the loader arms. If you enable Glide Ride™ or Auto-Glide Ride™ control with the key switch in the ON or ACC position, the loader arms can drop slightly due to the hydraulic accumulator. Failure to comply could result in death or serious injury.
Page 186: Parking The Unit
4 - OPERATING INSTRUCTIONS PARKING THE UNIT Parking the machine When parking the machine, follow the safety precautions mentioned in this manual. 1. Move the machine to a level and firm ground, away from any soft ground, excavations or poorly shored cavity.
Page 187: Transport Operations
5 - TRANSPORT OPERATIONS 5 - TRANSPORT OPERATIONS###_5_### ROAD TRANSPORT Precautions for road travel WARNING Avoid injury! Before starting the engine, securely fasten the seat belt. The seat belt can help ensure your safety if it is properly used and maintained. Never wear a seat belt loosely or with slack in the belt system. Never wear the belt if it is twisted or pinched between the seat structures.
Page 188: Preparing For Road Transport
5 - TRANSPORT OPERATIONS PREPARING FOR ROAD TRANSPORT Preparing the machine for road travel 1. If applicable. make sure that the engine accelerator knob (1) is in idle position. LEEN11T0149AA 2. Place all transmission controls in the NEUTRAL posi- tion. 3.
Page 189 5 - TRANSPORT OPERATIONS Mechanical transport lock 13. Lock the backhoe attachment: A. Press the button on the backhoe transport lock lever (1) and move it backward to engage the boom lock B. Retract the boom arm until the transport lock (2) en- gages.
Page 190 5 - TRANSPORT OPERATIONS 14. Raise the stabilizers. 15. Raise the loader about 20 cm (7.9 in) above the ground and roll back the loader bucket completely. 16. Correctly adjust the rearview mirrors (1). LEEN11T0128AA 17. Install the rotating beacon (1) on the cab roof, then connect the relative cable and operate the switch.
Page 191 5 - TRANSPORT OPERATIONS 23. If applicable, disengage the Four-Wheel Drive (4WD). LEEN11T0134AA_1 24. Machines with Power shuttle transmission. A. Press the transmission disconnect button (1) and then place the gearshift lever (2) in first gear. B. Release the button (1). LEEN11T0135AA_2 24.
Page 192 5 - TRANSPORT OPERATIONS 26. Position the direction-of-travel control lever (1) for- wards. LEEN11T0138AA 27. Release the brake pedals and adjust the travel speed by means of the accelerator pedal (1). 28. Shift gears as necessary. NOTE: Monitor all gauges and indicator/warning lamps frequently.
Page 193: Shipping Transport
5 - TRANSPORT OPERATIONS SHIPPING TRANSPORT Transporting on a trailer WARNING Transport hazard! The machine can slip or fall from a ramp or trailer. Make sure the ramp and trailer are not slippery. Remove all oil, grease, ice, etc. Move the machine on or off the trailer with machine centered on the trailer or ramp.
Page 194 5 - TRANSPORT OPERATIONS 12. Use chains and binders to fasten the machine to the trailer. Use the machine tie down locations. • Side chassis (both sides): • Backhoe (both sides): • Secure the backhoe bucket or attachment to the trailer.
Page 195: Lifting The Machine
5 - TRANSPORT OPERATIONS Lifting the machine NOTICE: Before lifting the machine, it is essential to place the backhoe attachment in the road travel position. The hooking points for the machine are shown by signs. NOTICE: Never use any other hooking points than those shown by the signs.
Page 196: Recovery Transport
Failure to comply could result in death or serious injury. W0259A NOTICE: NEW HOLLAND CONSTRUCTION does not recommend towing the machine. NOTICE: Do not attempt to start the engine while towing the machine. Damage to the drivetrain components will occur! If your machine is disabled, repair the machine at the job site unless you are able to move the machine without further damage.
Page 197 5 - TRANSPORT OPERATIONS Tow procedure - engine runs 1. Engage the parking brake. 2. Block the wheels with wheel chocks. 3. If applicable place the manual transmission lever in the NEUTRAL position. 4. Place the direction control lever in NEUTRAL. 5.
Page 198 5 - TRANSPORT OPERATIONS 5-12...
Page 199: Working Operations
6 - WORKING OPERATIONS 6 - WORKING OPERATIONS###_6_### GENERAL INFORMATION Forward-Neutral-Reverse (F-N-R) shift sensitivity NOTE: Machines with the optional Powershift transmissions only. Change F-N-R shift sensitivity: 1. Press Enter (4) to access the menu screens. 2. Press the up arrow (2) or the down arrow (3) to navi- gate through the menu screens.
Page 200: Display Brightness
6 - WORKING OPERATIONS Display brightness Adjust the brightness of the display: 1. Press Enter (4) to access the menu screens. 2. Press the up arrow (2) or the down arrow (3) to navi- gate through the menu screens. LEEN12T0526FA_4 3.
Page 201: Maximum Throttle/Cold Start Idle
6 - WORKING OPERATIONS Maximum throttle/Cold start idle The Idle Increment (engine speed) menu lets the operator configure the cold start idle and/or the maximum engine throttle settings. NOTE: The settings do not reset at key cycle. • Cold start idle - Sets the minimum engine speed (up to 1500 RPM) that the engine idles while cold.
Page 202 6 - WORKING OPERATIONS 3. When the Idle Increment screen displays, press Enter. RCPH10TLB201AAF 4. Press the up arrow or the down arrow until the cold start idle or the maximum throttle screen appears. 5. Press Enter. The setting flashes. 6.
Page 203: Throttle Sensitivity
6 - WORKING OPERATIONS Throttle sensitivity Change the throttle sensitivity: 1. Press Enter (4) to access the menu screens. 2. Press the up arrow (2) or the down arrow (3) to navi- gate through the menu screens. LEEN12T0526FA_4 3. When the Throttle Sensitivity screen displays, press Enter.
Page 204: Auto Engine Shutdown Time-Out Adjustment
6 - WORKING OPERATIONS Auto engine shutdown time-out adjustment NOTE: The default setting is Off. NOTICE: After the machine has been turned off by this feature it will appear completely off, but there are relays still consuming power. So, it is important to turn the key to Off before letting the machine sit for an extended period of time.
Page 205 6 - WORKING OPERATIONS 4. Press the Up arrow or the Down arrow to adjust the time-out setting. The number below the symbol is the time-out value in minutes or Off. NOTE: Select between Off, range of 2 – 5 min in 1 min increments, or a range of 5 –...
Page 206 6 - WORKING OPERATIONS Stop an auto engine shutdown The instrument cluster will provide a warning on the display screen during the 1 min period before the engine will be shut off. • Press the Escape (1) button to cancel the shutdown. NOTE: The number below the auto engine shutdown sym- bol indicates the number of seconds that remain before the shutdown will occur.
Page 207: Auto Engine Protection Shutdown Setting
6 - WORKING OPERATIONS Auto engine protection shutdown setting NOTE: The default setting is ON. NOTICE: After the machine has been turned off by this feature it will appear completely off, but there are relays still consuming power. So, it is important to turn the key to OFF before letting the machine sit for an extended period of time.
Page 208 6 - WORKING OPERATIONS 6. Use the arrows to navigate to a different menu screen or press Escape (1) until you return the main screen (engine hourmeter). LEEN12T0526FA_4 6-10...
Page 209: Auto-Glide Ride™ (Agr) Speed Thresholds
6 - WORKING OPERATIONS Auto-Glide Ride™ (AGR) speed thresholds Change the Auto-Ride Control™ (ARC) speed threshold: 1. Press Enter (4) to access the menu screens. 2. Press the up arrow (2) or the down arrow (3) to navi- gate through the menu screens. LEEN12T0526FA_4 3.
Page 210: Loader Attachment
6 - WORKING OPERATIONS LOADER ATTACHMENT Personal safety This manual contains only basic information that you need to operate the machine, it does not include all possible conditions for loader operation. If you are a new operator, always operate in a clear area at a decreased engine speed. Be a careful operator.
Page 211: Job Layout
6 - WORKING OPERATIONS Job layout WARNING Hazard to bystanders! Always know the location of all workers in your area. Warn them before you start operating the ma- chine. Always keep all unauthorized bystanders clear of the work area. Failure to comply could result in death or serious injury. W0206A WARNING Hazard to bystanders!
Page 212: Operating The Loader Attachment
6 - WORKING OPERATIONS Operating the loader attachment The following instructions do not cover all possible con- ditions of use of the loader attachment. The instructions contain only basic information to enable you to operate the machine correctly. Where possible, always use the loader attachment at full engine speed.
Page 213 6 - WORKING OPERATIONS Dump the bucket completely, raise the attachment and then release the transmission disconnect button. Keep the bucket position as low as possible, especially when working on sloping or rough ground. WARNING Loss of control hazard! A full bucket in the raised position may cause the machine to slide when operating over rough ground.
Page 214 6 - WORKING OPERATIONS For site stripping peeling or scraping, use down pressure with the loader attachment lever in the lowered position, and a slight bucket angle to start the cut. Begin the cut at the notch approximately 50 mm (1.97 in) deep and hold the depth by feathering the bucket to adjust the cutting lip up or down as required.
Page 215: Loader Digging Force
6 - WORKING OPERATIONS Loader digging force Transmission disconnect button Press the transmission disconnect button to increase engine speed and supply the loader with more hydraulic oil for greater loader power and faster control function. Press and hold the transmission disconnect button on the back of the loader control lever, the transmission will dis- engage from the drive wheels.
Page 216: Loader Attachment Safety Strut
6 - WORKING OPERATIONS Loader attachment safety strut WARNING Crushing hazard! If you service the machine with the loader lift arms raised, always use the support strut. Remove the retaining pin and place the support strut onto the cylinder rod. Install the retaining pin into the support strut.
Page 217 6 - WORKING OPERATIONS Disengage the loader arm support strut: 1. Completely raise the loader attachment and stop the engine. 2. Remove the split pin (1) and the lock pin (2). MOLI12LBB0262AB 3. Remove the strut (3) from the attachment and install the pin (1) and the split pin (2) back into the holes in the strut.
Page 218 6 - WORKING OPERATIONS Machines with the Tool Carrier (TC) option Engage the loader arm support strut: 1. Remove the split pins (1) and the safety strut (2) from the arm. Put the split pins back in place. 2. Empty the loader bucket. 3.
Page 219: Loader Bucket Removal
6 - WORKING OPERATIONS Loader bucket Removal B95C - B95CLR - B110C 1. Move the machine to a level and firm ground. 2. Lower the bucket to the ground in dump position (tilted completely forward). 3. Stop the engine and remove the starter switch key.
Page 220: Loader Bucket Installation
6 - WORKING OPERATIONS Loader bucket Installation B95C - B95CLR - B110C Make sure all bushings are completely clean. Re- move any dirt or foreign matter, if necessary. Start the engine. Use the attachment controls to engage the attach- ment between the bucket lugs.
Page 221: Loader Bucket With Quick Coupler (B95Ctc)
6 - WORKING OPERATIONS Loader bucket with quick coupler (B95CTC) The loader hydraulic coupler allows the operator to change front end attachments without using special tools or ad- ditional manpower. Installation 1. Make sure the bucket is in a safe area, on a level and firm ground and with the upper pins in place.
Page 222 6 - WORKING OPERATIONS 5. Lift the loader attachment and rotate the quick coupler rearwards until the lock pins (6) are aligned with the lower bores of the bucket. 6. Release the switch (3) allowing the lock pins (5) to engage in the mounting bores of the bucket.
Page 223: Loader Bucket With Forks (Optional)
6 - WORKING OPERATIONS Loader bucket with forks (optional) NOTICE: The forks are heavy, so use great care when swinging them into their working and stowage position. Install forks in working position 1. Move the bucket to a level and firm ground. 2.
Page 224 6 - WORKING OPERATIONS Install the forks in rest position 1. Rest the loader bucket on a level and firm ground. 2. Stop the engine and remove the starter switch key. 3. Disengage the parking brake. 4. Remove the retained pin and the pin (1). 5.
Page 225: Lifting Loads With The Loader Attachment
6 - WORKING OPERATIONS Lifting loads with the loader attachment WARNING Heavy object! ALWAYS use adequate lifting equipment (heavy-duty hoist, loader, or forklift) to lift the component. Failure to comply could result in death or se- rious injury. W0101A Loader bucket - with lifting ring The lifting ring is the only point to which loads may be attached on the loader bucket.
Page 226 6 - WORKING OPERATIONS Maximum lifting loads with forks equipped) on loader bucket CAUTION Equipment failure could cause accident or in- jury! Never exceed the maximum safe working load of the loader. Failure to comply could result in minor or moderate injury.
Page 227: Backhoe Attachment
6 - WORKING OPERATIONS BACKHOE ATTACHMENT Personal safety This manual contains only basic information that you need to operate the machine, it does not include all possible conditions for backhoe operation. Be a careful operator. You can prevent accidents. Do not allow yourself to become complacent. Basic instructions WARNING Unexpected machine movement!
Page 228: Backhoe Danger Area
6 - WORKING OPERATIONS Backhoe danger area WARNING Crushing hazard! Never place loose items in the operator's platform. Never walk into the danger area to place loose items in the operator's platform. You could inadvertently actuate a control. Failure to comply could result in death or serious injury. W1450A WARNING Hazard to bystanders!
Page 229: Swing Lock
6 - WORKING OPERATIONS Swing lock Install the backhoe swing lock pin Make sure the backhoe swing lock pin is in the LOCK position whenever the backhoe is not in use. To install the backhoe swing lock pin: 1. Place the seat in the backhoe operating position. 2.
Page 230: Basic Instructions
6 - WORKING OPERATIONS Basic instructions WARNING Avoid injury! Read and follow the instructions in this manual. Failure to comply could result in death or serious injury. W1212A The below instructions contain only basic information to enable you to operate the machine correctly. Make sure that all the safety precautions listed in this manual are followed when the backhoe attachment is used.
Page 231: Setting The Backhoe Attachment In Working Position - Center Pivot
6 - WORKING OPERATIONS Setting the backhoe attachment in working position – center pivot WARNING Unexpected machine movement! Before you use the backhoe attachment, make sure that the machine is resting on the stabilizers. Failure to comply could result in death or serious injury. W1326A WARNING Unexpected machine movement!
Page 232 6 - WORKING OPERATIONS Removing the backhoe from the stowed position (mechanical) 1. Start the machine. 2. Place the direction control lever in NEUTRAL position. 3. If applicable, place gearshift control lever in the NEU- TRAL position. 4. Turn the seat into the backhoe operation position. 5.
Page 233 6 - WORKING OPERATIONS Move the boom all the way towards you to relieve pressure on the boom lock (2). Press the button on the boom lock control lever (1) and move forward to disengage the boom lock. 10. Lower the boom. RAIL15TLB0050AA RAIL15TLB0051AA 11.
Page 234 6 - WORKING OPERATIONS Removing the backhoe from the stowed position (hydraulically, if equipped) 1. Start the machine. 2. Place the direction control lever in NEUTRAL position. 3. If applicable, place gearshift control lever in the NEU- TRAL position. 4. Turn the seat into the backhoe operation position. 5.
Page 235 6 - WORKING OPERATIONS 8. Place the switch (1) in the OFF position to disengage the hydraulic boom lock (2) . The indicator lamp (3) (mechanical backhoe models) or the indicator lamp (4) (pilot backhoe models) turns OFF. 9. Lower the boom. LEEN11T0311AA RAIL15TLB0547BA MOLI12LBB0249AB...
Page 236 6 - WORKING OPERATIONS 10. If applicable, remove the extendable dipper lock pin (1) and place it in the storage position (2). RAIL15TLB0545BA 6-38...
Page 237: Stabilizer Pads
6 - WORKING OPERATIONS Stabilizer pads WARNING Tip-over hazard! Put the stabilizers in the operating position before you lower the boom and extend the dipper. The front of the machine can raise above the ground and become unstable if the stabilizers are not down in the operating position.
Page 238 6 - WORKING OPERATIONS Combination flip-over stabilizer pads: • Working on paved surfaces (rubber pad down) (1) • Working on unpaved surfaces (rubber pad up) (2) MOLI12LBB0515AA 6-40...
Page 239: Operating The Backhoe Attachment
6 - WORKING OPERATIONS Operating the backhoe attachment Digging method RCPH10TLB004GAF 1. Correct bucket position 2. Incorrect bucket position 3. Correct trenching method 4. Incorrect trenching method Operating techniques NOTICE: Never operate any of the backhoe attachment control levers with arm locked in transport position. 6-41...
Page 240 6 - WORKING OPERATIONS Filling the backhoe bucket Fill the backhoe bucket by maneuvering the dipper. Keep the bottom of the backhoe bucket parallel to the cut. The backhoe bucket teeth and blade must cut the ground like the blade of a knife. The depth of dig varies depending on the type of material.
Page 241 6 - WORKING OPERATIONS Telescopic dipper NOTICE: To avoid the risk of damage and to extend the overall life of machines fitted with a telescopic dipper, ob- serve the following precautions. When the attachment is used for compacting operations, the telescopic dipper must be fully retracted and locked. LEEN12T0666AA 1.
Page 242 6 - WORKING OPERATIONS Do not bottom-out the swing cylinder with the dipper ex- tended. NOTICE: For safety reasons, when working on sloping ground, do not swing the boom to dump the bucket con- tents on the side sloping down. WARNING Uncontrolled equipment movement! Windows can interfere with backhoe control...
Page 243 6 - WORKING OPERATIONS Trenching Trenching is the most basic backhoe excavating opera- tion. Other digging operations are merely variations of this ba- sic function (filling the bucket, dumping the bucket and moving the machine forward). While trenching, it is generally important to maintain a level trench bottom.
Page 244 6 - WORKING OPERATIONS When finishing straight walls in sandy soil, position a plat- form under the rear tires and stabilizers to distribute the load over a larger area and reduce the possibility of a cave-in. The platform will also reduce the possibility of the machine creeping rearwards if hard digging is encountered.
Page 245: Backhoe Bucket - Remove
6 - WORKING OPERATIONS Backhoe bucket – Remove 1. Move the machine to a level and firm ground. 2. Lower the stabilizers and place the bucket on the ground. 3. Stop the engine and remove the starter switch key. CAUTION Flying objects! Wear eye protection.
Page 246: Backhoe Bucket - Install
6 - WORKING OPERATIONS Backhoe bucket – Install 1. Start the engine. 2. Extend the bucket cylinder rod to bring the connecting rod to their housing. 3. Reinstall the arm/bucket link pin (2), then install the lock rings and pins. 4.
Page 247: Backhoe Bucket - Digging Angle
6 - WORKING OPERATIONS Backhoe bucket – Digging angle It is possible to change the backhoe bucket opening an- gle, depending on the work which is to be carried out. Position (1): Enables the bucket to open by 30° more and, therefore, to dig vertical side trenches closer to the ma- chine.
Page 248: Ballasting
6 - WORKING OPERATIONS Ballasting Tire liquid ballasting Tire size Water Tire total weight Calcium chloride 12.5/80-18 89 L (23.51 US gal) 53 kg (117 lb) 142 kg (313 lb) 227 L (59.97 US gal) 136 kg (300 lb) 363 kg (800 lb) 16.9-28 NOTE: The tires shown in the table above are for general outfit.
Page 249 6 - WORKING OPERATIONS Weighting limitations WARNING Overturning hazard! If the counterweights (of adequate capacity) mentioned in this manual are added, DO NOT operate the loader with the backhoe removed. Operating the unit with less than the recom- mended rear counterweight may cause the unit to become unstable and overturn.
Page 250 6 - WORKING OPERATIONS Machine weighing When adding ballast to the machine, do not exceed the gross weight shown on the identification plates. NOTE: The total weight on the rear axle is measured with only the rear wheels on the scales, the weight on the front axle is measured with only the front wheels on the scales.
Page 251: Lifting Loads With Backhoe Attachment
6 - WORKING OPERATIONS Lifting loads with backhoe attachment 1. Move the machine to a level and firm ground. 2. Retract the loader bucket completely and then let the bucket weight press against the ground. 3. Lower the loader attachment until the front wheels just touch the ground without supporting the weight of the machine.
Page 252 6 - WORKING OPERATIONS 6-54...
Page 253: Maintenance
(dusty or corrosive atmosphere, etc.), reduce LAND CONSTRUCTION strongly recommends that you the time between the service intervals. use only authorized NEW HOLLAND CONSTRUCTION Before performing any operation on the machine, make dealers and products that meet given specifications. Im-...
Page 254 7 - MAINTENANCE Machine safety and best practices WARNING Crushing hazard! If you service the machine with the loader lift arms raised, always use the support strut. Remove the support strut from the storage position and place the strut onto the cylinder rod. Install the retaining bolt entirely into the strut.
Page 255 Tips and best practices NOTE: Contact your dealer with any questions regarding the service and maintenance of this machine. • Use NEW HOLLAND CONSTRUCTION fluids, lubri- cants, and filters for the best protection and perfor- mance of your machine. • Perform maintenance procedures in a timely matter.
Page 256: Fire Extinguisher
7 - MAINTENANCE Fire extinguisher The NEW HOLLAND CONSTRUCTION recommends that you keep a fire extinguisher on your machine at all times. A fire extinguisher is available from your dealer. This dry chemical fire extinguisher has a 2 kg (5 lb) capacity. This type of fire extinguisher is approved for class A, B, and C type fires.
Page 257: Capacities - B95C, B95C Lr, And B95C Tc
7 - MAINTENANCE Capacities - B95C, B95C LR, and B95C TC Engine crank case Specification: 10W-40( API CJ-4) NGINE YNTHETIC Capacity: With filter change 8.0 L (8.5 US qt) Fuel tank Specification: ASTM D975 G . 2-D S15 (No. 2 diesel)
Page 258 7 - MAINTENANCE Front drive axle - Four-Wheel drive (4WD) Specification: 80W-140 REMIUM RANSAXLE Capacity: Differential 6.5 L (6.9 US qt) Each planetary hub 0.7 L (0.7 US qt) Rear axle (differential and hubs) Specification: 80W-140 REMIUM RANSAXLE Capacity: 21.2 L (22.4 US qt)
Page 259: Capacities - B110C
7 - MAINTENANCE Capacities – B110C Engine crank case Specification: 10W-40( API CJ-4) NGINE YNTHETIC Capacity: With filter change 8.0 L (8.5 US qt) Fuel tank Specification: ASTM D975 G . 2-D S15 (No. 2 diesel) RADE Capacity: 131.0 L (34.6 US gal) Emissions fluid tank Specification: (DEF)/A...
Page 260 7 - MAINTENANCE Front drive axle - Four-Wheel drive (4WD) Specification: 80W-140 REMIUM RANSAXLE Capacity: Differential 6.5 L (6.9 US qt) Each planetary hub 0.7 L (0.7 US qt) Rear axle (differential and hubs) Specification: 80W-140 REMIUM RANSAXLE Capacity: 21.2 L (22.4 US qt)
Page 261: Engine Hood
7 - MAINTENANCE Engine hood NOTICE: It is essential to install the loader attachment support strut before any servicing work is done on the engine. Open the engine hood: 1. Insert the key (1) and turn counter-clockwise. 2. Push the key slot on the engine latch to release the lock (2).
Page 262: Fuel Tank
LAND CONSTRUCTION dealer. Instructions for the use • Stabilize fuel in storage of the fuel conditioner is on the container. NOTICE: Use only NEW HOLLAND CONSTRUCTION The use of diesel fuel conditioner will: approved biocide additives to prevent damage to the ex- haust aftertreatment system (if equipped).
Page 263: General Specification - Biodiesel Fuels
Cold Pressed Oil, Straight Vegetable Oil (SVO), or more generally unrefined vegetable oils used as motor fuel are Biodiesel fuel has several positive features in comparison NOT APPROVED at any blend in any NEW HOLLAND with diesel fuel: CONSTRUCTION product.
Page 264 20 hours to flush the biodiesel fuel out of the fuel system conditions for biodiesel fuel handling and maintenance prior to storage. will not be covered for Warranty by NEW HOLLAND Biodiesel is highly hygroscopic and tends to collect water CONSTRUCTION.
Page 265: Selective Catalytic Reduction (Scr) Exhaust Treatment - Basic Instructions
See “General specification - Biodiesel fuels” for details on biodiesel fuel usage in your NEW HOLLAND CONSTRUC- TION machine.
Page 266 NOTE: DEF/AdBlue® consumption is highly dependent on engine loads, humidity levels, DEF/AdBlue® fluid concen- tration, and engine speed. The “typical” consumption is only a guideline to verify proper function of the SCR system. NEW HOLLAND CONSTRUCTION recommends to fill the DEF/AdBlue® tanks at every fuel refilling interval. 7-14...
Page 267: Hydraulic Oil
7 - MAINTENANCE Hydraulic oil For the first filling, the Manufacturer uses H YDRAULIC RANSMISSION REMIUM Hydraulic oil is not water-soluble; this can cause the for- mation of condensation water in the hydraulic oil tank. Therefore, periodically drain condensation water, espe- cially after the machine has been left unused for a long time.
Page 268 7 - MAINTENANCE Hydraulic oil tank The hydraulic oil tank (1) is located on the right hand side of the machine, under the cab. NOTE: Tank capacity fill to the sight glass line is 50.8 L (13.4 US gal). The oil level can be checked through the sight glass (2). The hydraulic oil tank can be filled through the fill cap/ breather (3).
Page 269: Recommended Engine Oil For Operating Temperature Ranges
(H) = Engine oil pan or coolant block heater recommended in this range Engine oil and filter service intervals NEW HOLLAND CONSTRUCTION develops the oil/filter change intervals given in this manual from tests with NEW HOLLAND CONSTRUCTION lubricants/filters. Engine oil and filter service interval recommendations are based on type of engine oil, oil filter used, sulfur, Bio-diesel content of diesel fuel.
Page 270: Organic Acid Technology (Oat) Coolant
7 - MAINTENANCE Organic Acid Technology (OAT) coolant NEW HOLLAND CONSTRUCTION requires the use of a fully formulated Organic Acid Technology (OAT) based coolant. OAT E is preferred. The coolant must meet the specifications outlined XTENDED OOLANT NTIFREEZE in the CNH Industrial material specification MAT3624. Use of coolant not meeting this specification is not allowed.
Page 271: Diagnostic/Service Tool Port
7 - MAINTENANCE Diagnostic/Service tool port Connect the Electronic Service Tool (EST) or DATAR to this port to update software and/or perform service and diag- nostic tests. 1. Remove the main fuse cover panel cover from the front right-hand side console. RAIL16TLB0532BA 2.
Page 272: Hydraulic Diagnostic Test Ports
7 - MAINTENANCE Hydraulic diagnostic test ports Easily check the machine’s hydraulic system pressure from two locations on the machine. Each location has hydraulic quick connect diagnostic test port(s). One location is on the left-hand side of the machine above the fuel tank behind a cover panel and the second location is near the right-hand stabilizer on the inside of the chassis.
Page 273 7 - MAINTENANCE Machines with backhoe mechanical con- trols: • Load sense pressure test port (1) • Pump output pressure test port (2) • Mechanical pressure test port (3) 84411882 Rear port (attenuator hose) – All machines At the attenuator hose connector test for pump output pressure, hydraulic flow, or bleed air from the system.
Page 274: Work Hours And Intervals
7 - MAINTENANCE Work hours and intervals One of the premises for the manufacturer to satisfy the warranty obligations is the regular performance of all in- spection, maintenance and repair operations prescribed, according to the instructions given in this manual, as well as the use of original spare parts.
Page 275: Maintenance Chart
7 - MAINTENANCE MAINTENANCE CHART Maintenance chart Drain fluid Cleaning Filling Grease Check Adjust Replace Change fluid Maintenance action Page no. At warning message display 7-25 Engine air filters Hydraulic filter(s) 7-27 Fuel system water separator 7-29 Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank - Filling 7-31 7-32 Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank - Drain fluid...
Page 276 7 - MAINTENANCE Drain fluid Cleaning Filling Grease Check Adjust Replace Change fluid Maintenance action Page no. Engine oil and filter 7-83 7-87 Fuel filter Fuel prefilter 7-88 Diesel Exhaust Fluid (DEF)/AdBlue® tank filler screen 7-90 Diesel Exhaust Fluid (DEF)/AdBlue® in-line filter 7-92 Every 1000 hours Hydraulic oil filter...
Page 277: At Warning Message Display
7 - MAINTENANCE At warning message display Engine air filters Clean or replace the engine air filter whenever the warning lamp remains illuminated while the engine is running. 1. Clean the area around the outside front cover of the air filter housing.
Page 278 7 - MAINTENANCE 5. With the primary filter removed, use a lint-free cloth tied to a stiff rod and wipe the inside of the housing clean. Avoid touching the inner filter. RAIL14TLB0976AA 6. Remove the inner filter only if the outside of it is dirty, replace the inner filter do not clean.
Page 279: Hydraulic Filter(S)
7 - MAINTENANCE Hydraulic filter(s) NOTICE: Always replace the hydraulic filter whenever the warning lamp remains illuminated while the engine is running. NOTICE: Oil quality and cleanliness are of utmost importance for the reliability and life of the hydraulic system. De- viation from the prescribed oil specification may lead to severe damage and void warranty.
Page 280 7 - MAINTENANCE 3. Clean the area around the filter head area before re- moving the old filter. Wear eye protection to keep dirt and debris from eyes. 4. Use a filter wrench and remove the old filter. Have a suitable container ready to capture any fluid that might leak or spill.
Page 281: Fuel System Water Separator
7 - MAINTENANCE Fuel system water separator Drain the water separator and check the fuel tank when- ever the engine fault indicator lamp (1) illuminates, the audible alarm sounds, and the water in fuel system screen (2) appears in the display. NOTICE: The indicator lamp only illuminates at potential problems.
Page 282 7 - MAINTENANCE 2. Hold a small container under the water separator and loosen the drain valve. 3. Collect a small amount of fluid and inspect for water or sediment. 4. Drain until water or sediment is no longer present. 5.
Page 283: Diesel Exhaust Fluid (Def)/Adblue®/Arla Tank - Filling
7 - MAINTENANCE Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank - Filling Diesel Exhaust Fluid (DEF)/AdBlue® tank capacity: 13.5 L (3.6 US gal). When theDiesel Exhaust Fluid (DEF)/AdBlue® low fluid symbol appears in the display you will also notice one of the following symbols illuminate on the instru- ment cluster: Warning symbol and an audible alert.
Page 284: Diesel Exhaust Fluid (Def)/Adblue®/Arla Tank - Drain Fluid
7 - MAINTENANCE Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank - Drain fluid Diesel Exhaust Fluid (DEF)/AdBlue® tank capacity: 13.5 L (3.6 US gal). When the Diesel Exhaust Fluid (DEF)/AdBlue® poor quality symbol appears in the display you will also no- tice one of the following symbols illuminate on the in- strument cluster: Warning symbol and an audible alert.
Page 285 7 - MAINTENANCE 3. Place a suitable container below theDEF/AdBlue® tank drain plug. RAIL15TLB0033AA 4. Install the DEF/AdBlue® tank drain plug. 5. Install the cover plate. 6. If applicable, clean the “Diesel Exhaust Fluid (DEF)/ AdBlue® tank filler screen” 7-90, the “Diesel Exhaust Fluid (DEF)/AdBlue®...
Page 286: Hydrocarbon Management
7 - MAINTENANCE Hydrocarbon management NOTICE: Unless the Hydrocarbon (HC) level has reached the most critical level (SCR catalyst full ), running the unit under load is advantageous for quickly reducing the HC levels. If the engine operates at low idle speed for a prolonged period of time, hydrocarbons can accumulate in the SCR cat- alyst.
Page 287: Initial 10 Hours
7 - MAINTENANCE Initial 10 hours Wheels - Check NOTE: Depending on the manufacturing date of your machine the front wheel mounting hardware may be either lug nuts or bolts with washers. Check the wheel torque that is applicable to your machine. NOTICE: Small variations in the friction force between the wheel and the mounting hardware, such as lubricant, lack of lubricant, paint, surface rust, thread variations, etc., will cause large variations in the clamping force.
Page 288 7 - MAINTENANCE Rear wheel 1. Tighten the five mounting nuts in the sequence shown until the wheel is snug against the axle hub. 2. Tighten the nuts in sequence to a torque of 136 N·m (100 lb ft). 3. Tighten the nuts a second time, in sequence, to a torque of 271 N·m (200 lb ft).
Page 289: Every 10 Hours
7 - MAINTENANCE Every 10 hours Checks at start-up and before each workshift (10 hours) Machine - General inspection Before using the machine, it is recommended to per- form a general inspection. Externally check the machine and its working attach- ments, checking for possible breaks or damage of the components or the structure.
Page 290: Working Attachments - Loader Attachment
7 - MAINTENANCE Working attachments — Loader attachment Loader attachment 1. Lubricate the loader attachment. NOTE: The number of grease points may vary depending on the type of accessory installed. Number of grease fittings: 26 LEEN11T0365AA Grease specifications Use M ULTI URPOSE REASE...
Page 291: Working Attachments - Backhoe Attachment
7 - MAINTENANCE Working attachments — Backhoe attachment Backhoe attachment 1. Lubricate the backhoe attachment. NOTE: The number of grease points may vary depending on the type of accessory installed. Number of grease fittings: 30 LEEN11T0367AA Grease specifications 2. Use M ULTI URPOSE REASE...
Page 292: Windshield Washer Fluid Level - Check
NOTICE: The windshield wiper motor is gravity-fed. Do not remove the rubber tube as damage can be caused if liquid gets into the motor. LEEN12T0570AA Fluid specification and capacity Use C or a wind- ONCENTRATED INDSCREEN screen washer fluid approved by NEW HOLLAND CONSTRUCTION. 7-40...
Page 293: Engine Oil Level - Check
7 - MAINTENANCE Engine oil level — Check 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion.
Page 294 7 - MAINTENANCE 11. If the oil level is below the add mark, remove the filler cap (2), and add E 10W-40 NGINE YNTHETIC to raise the level up to the full mark on the dipstick. 12. Reinstall the filler cap (2). RAIL15TLB0025AA 13.
Page 295: Engine Coolant - Check
7 - MAINTENANCE Engine coolant — Check WARNING Hot liquid under pressure! Scalding can result from fast removal of the radiator cap. Check and service the engine cooling sys- tem according to the maintenance instructions in this manual. Failure to comply could result in death or serious injury. W0163A 1.
Page 296: Radiator, Oil Cooler, And Condenser - Check
7 - MAINTENANCE Radiator, oil cooler, and condenser — Check WARNING Hot liquid under pressure! Scalding can result from fast removal of the radiator cap. Check and service the engine cooling sys- tem according to the maintenance instructions in this manual. Failure to comply could result in death or serious injury.
Page 297: Alternator - Check
7 - MAINTENANCE Alternator — Check 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 298: Hydraulic Oil Level - Check
7 - MAINTENANCE Hydraulic oil level — Check 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 299 7 - MAINTENANCE 10. If necessary, remove the tank fill cap/breather (3) with the special wrench (4) and add additional H YDRAULIC until the level is correct RANSMISSION REMIUM inside of the level sight gauge. NOTE: Even when oil level is insufficient, a small quantity of hydraulic oil remains in the lower part of the gauge.
Page 300: Hydraulic Hoses, Tubes, And Fittings
7 - MAINTENANCE Hydraulic hoses, tubes, and fittings WARNING Hot liquid under pressure! If leaks are detected in the hydraulic hoses, tubes, or fittings during the inspection, carry out the following before you perform any maintenance activities: 1. Stop the engine. 2.
Page 301: Every 50 Hours
7 - MAINTENANCE Every 50 hours Working attachments - greasing Telescopic dipper rails NOTICE: Before applying new grease on the sliding surfaces, clean and remove all dirt accumulations and foreign bodies. 1. Apply grease on the sliding surface of the telescopic dipper rails (1).
Page 302: Door Hinges
7 - MAINTENANCE Door hinges 1. Lubricate the door hinges. The number of grease fit- tings (1): 4 LEEN11T0373AA Grease specifications Use M ULTI URPOSE REASE XTREME PRES- NGLI-2. SURE AND ANTI WEAR Front axle trunnion Front axle - Greasing 1.
Page 303: Front Axle King Pins
7 - MAINTENANCE Front axle king pins Axle articulations - Greasing 1. Locate the grease fittings (1) on the top and bottom of each side of the front axle. Lubricate the axle ar- ticulation points with M ULTI URPOSE REASE NGLI-2.
Page 304: Seat And Seat Belt
7 - MAINTENANCE Seat and seat belt Seat suspension and rails - Clean and lubrication 1. Check the operation of the operator’s seat and of the seat belt, and the solidity of the seat belt mountings. 2. Replace parts showing signs of wear or damage. 3.
Page 305: Fuel Pre-Filter - Draining Condensation
7 - MAINTENANCE Fuel pre-filter - draining condensation WARNING Fire hazard! Avoid injury and/or machine damage! During maintenance activities, make sure that the high-pressure fuel lines are not damaged. A fuel leak from the high-pressure fuel lines can cause an accident and/or serious personal injury. If the fuel lines are damaged, contact your dealer immediately.
Page 306 7 - MAINTENANCE 12. Remove the connector (2) from the bottom of the filter. 13. Install a drain pipe (about 1 m long 3.2 ft) on the drain valve, (3) and put the other end of the pipe into the container.
Page 307: Tire Pressure
7 - MAINTENANCE Tire pressure WARNING Explosion hazard! A tire can explode during inflation. Replace a tire if it has any defect(s). Replace a wheel rim that has cracks, wear, or severe rust. Failure to comply could result in death or serious injury. W0455A WARNING Explosion hazard!
Page 308 7 - MAINTENANCE Inflating procedure 1. Move the machine to a level and firm ground. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in neutral position.
Page 309 7 - MAINTENANCE Inflating pressure and allowed carrying capacity table NOTE: The following tables give the approximate carrying capacity at the indicated tire pressures when traveling at a maximum speed of 30 km/h (19 mph). INFLATION PRESSURE bar (psi) Tire (21.8) (29.0) (31.9)
Page 310 7 - MAINTENANCE INFLATION PRESSURE bar (psi) Tire (17.4) (20.3) (21.7) (27.5) (31.9) (49.3) size Profile Rear 21L– MAX LOAD PER TIRE kg (lb) 24 EZ 2455 2840 3005 3165 3760 4030 (5412) (5467) (6624) (6977) (8289) (8884) 7-58...
Page 311: Every 250 Hours
7 - MAINTENANCE Every 250 hours Drive shaft lubrication Cardan shafts - Greasing 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion.
Page 312: Engine Cooling System - Check
7 - MAINTENANCE Engine cooling system — Check Cooling system lines - Check 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion.
Page 313: Fuel Tank - Drain Fluid
7 - MAINTENANCE Fuel tank - Drain fluid 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 314: Hydraulic Oil Tank Breather / Filler Cap - Cleaning
7 - MAINTENANCE Hydraulic oil tank breather / filler cap - cleaning CAUTION Flying debris! Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using com- pressed air. Failure to comply could result in minor or moderate injury. C0049A 1.
Page 315: Transmission Oil Level
7 - MAINTENANCE Transmission oil level NOTICE: Check the oil level with the engine running at low speed and at normal operating temperature. 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut.
Page 316: Front Axle Breather (4Wd) - Clean
7 - MAINTENANCE Front axle breather (4WD) - Clean 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 317: Front Axle And Reduction Gear Oil Level (4Wd)
7 - MAINTENANCE Front axle and reduction gear oil level (4WD) 1. Move the machine to a level and firm ground. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4.
Page 318 7 - MAINTENANCE Reduction gear oil level 1. Raise the front part of the machine with the loader at- tachment until the front wheels are no longer in contact with the ground, and place a suitable support under the front axle. 2.
Page 319: Front Axle System - Check - (2Wd)
7 - MAINTENANCE Front axle system - Check — (2WD) 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 320: Rear Axle Oil Level - Check
7 - MAINTENANCE Rear axle oil level - Check 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 321: Rear Axle Breather
7 - MAINTENANCE Rear axle breather Rear axle breather valve - Cleaning 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion.
Page 322: Radiator And Condenser - Cleaning
7 - MAINTENANCE Radiator and condenser - cleaning 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion.
Page 323 7 - MAINTENANCE 18. Remove the safety support strut and lower the loader attachment. 7-71...
Page 324: Drive Belts - Check
7 - MAINTENANCE Drive belts - check 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion. 4.
Page 325: Cab Air Filter
7 - MAINTENANCE Cab air filter NOTICE: In humid conditions do not switch on the blower prior to servicing the filter. 1. Park the machine on level ground. 2. Stop the engine and remove the starter switch key. 3. Lift the grid cover (1) upward and remove it from the filter housing.
Page 326 7 - MAINTENANCE 6. Gently pull the top of the filter (1) away from the housing and lift the filter out. NOTE: Replace filter if damage occurs or excessive wear is apparent. 7. Do not clean the filter (1) with air or water pressure. 8.
Page 327 7 - MAINTENANCE 13. Slide the grid cover over the filter housing. Make sure that the sliding cover rails (1) engage with the filter housing rails (2) on both sides. 14. Make sure that the grid cover is evenly and fully in the down position.
Page 328: Heater And Evaporator (Air-Conditioning System) - Cleaning
7 - MAINTENANCE Heater and evaporator (Air-conditioning system) - Cleaning CAUTION Flying debris! Compressed air can propel dirt, rust, etc. into the air. Wear eye and face protection when using com- pressed air. Failure to comply could result in minor or moderate injury. C0049A 1.
Page 329: Telescopic Dipper
7 - MAINTENANCE Telescopic dipper The telescopic dipper is equipped with adjustable wear pads (4). Adjust the wear pads as follows: 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Retract the telescopic dipper and place it on a support so that the bucket does not rest on the ground.
Page 330: Battery Terminals
7 - MAINTENANCE Battery terminals 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 331 7 - MAINTENANCE 8. Remove the four bolts (1) and the battery cover (2). RAIL15TLB0073AA RAIL15TLB0074AA 9. Check the battery terminals (3) to ensure they are se- cure. RAIL15TLB0075AA 7-79...
Page 332: Cab Protection System
7 - MAINTENANCE Cab protection system This section provides information about Roll Over Pro- tective Structure (ROPS) and Falling Objects Protective Structure (FOPS). Always adhere to the safety precautions related to the Cab protections systems listed below: • The machine is provided with a safety structure for the operator: •...
Page 333 7 - MAINTENANCE WARNING Roll-over hazard! After an accident, fire, tip over, or roll over, a qualified technician MUST replace the Roll-Over Protective Structure (ROPS) before returning the machine to the field or job site operation. Failure to comply could result in death or seri- ous injury.
Page 334 Age, weather, and accidents can cause damage to the ROPS and ROPS parts. If you have any doubt about the integrity of the ROPS system, see your NEW HOLLAND CONSTRUCTION Dealer. WARNING Tip-over hazard! Adding additional weight (buckets, attach- LEEN11T0377AA ments, etc.) to the machine can create a tipping...
Page 335: Every 500 Hours
7 - MAINTENANCE Every 500 hours Engine oil and filter WARNING Avoid injury! Avoid getting engine oil on your skin. In case of skin contact, wash with running water. Failure to comply could result in death or serious injury. W1336B WARNING Pressurized system! Never attempt to drain fluids or remove filters when the engine is running.
Page 336 7 - MAINTENANCE 10. Remove the drain plug (2) and drain the engine oil from the crankcase. RAIL15TLB0028AA 11. Place a container with suitable capacity under the fil- ter. NOTE: Perform the fuel filter replacement service at the same time as the engine oil and filter replacement service. The fuel filter must be removed to access the oil filter.
Page 337 7 - MAINTENANCE 16. Reinstall the drain plug (2). RAIL15TLB0028AA 17. Fill the engine with new oil through the filler neck (1). RAIL15TLB0025AA 18. Run the engine for a few minutes and check for leaks. NOTE: Always wait 15 min to allow the oil to return to the engine sump before checking the oil level. 19.
Page 338 7 - MAINTENANCE 20. The oil level should be at the full mark. If necessary, add oil to raise the oil level. LEEN11T0361AA 21. Reinstall the cap (1) on the filler neck. RAIL15TLB0025AA 22. Lower and lock the engine hood. 23.
Page 339: Fuel Filter
7 - MAINTENANCE Fuel filter 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 340: Fuel Prefilter
7 - MAINTENANCE Fuel prefilter WARNING Fire hazard! Avoid injury and/or machine damage! During maintenance activities, make sure that the high-pressure fuel lines are not damaged. A fuel leak from the high-pressure fuel lines can cause an accident and/or serious personal injury. If the fuel lines are damaged, contact your dealer immediately.
Page 341 7 - MAINTENANCE 11. Loosen and remove the fuel prefilter cartridge (2). RAIL15TLB0025AA 12. Assemble the new fuel prefilter cartridge. 13. Install and manually tighten the fuel prefilter cartridge (2) until the seal touches the filter head (3). 14. After contact, by hand, tighten the fuel prefilter car- tridge (2) an additional 3/4 of a turn.
Page 342: Diesel Exhaust Fluid (Def)/Adblue® Tank Filler Screen
7 - MAINTENANCE Diesel Exhaust Fluid (DEF)/AdBlue® tank filler screen 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 343 7 - MAINTENANCE 9. Turn the screen filter counter-clockwise and remove. RAIL15TLB0063AA 10. Rinse the screen filter with water. NOTICE: Inspect the filler screen and replace if damaged. 11. Air or blow dry the screen filter. RAIL15TLB0064AA 12. Fully Insert the screen filter and turn it clockwise. 13.
Page 344: Diesel Exhaust Fluid (Def)/Adblue® In-Line Filter
7 - MAINTENANCE Diesel Exhaust Fluid (DEF)/AdBlue® in-line filter 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 345 7 - MAINTENANCE 9. Locate and remove the quick connect supply (suction) tube. RAIL15TLB0077AA 10. Use a flat needle-nose pliers and pull the filter directly upward. RAIL15TLB0079AA 11. Clean the filter with water. RAIL15TLB0078AA 7-93...
Page 346 7 - MAINTENANCE 12. Reinstall the filter. RAIL15TLB0079AA 13. Connnect the supply (suction) tube. you will hear it snap into place. RAIL15TLB0080AA 14. Reinstall the cover for the sending unit. RAIL15TLB0081AA 7-94...
Page 347: Every 1000 Hours
7 - MAINTENANCE Every 1000 hours Hydraulic oil filter 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 348 7 - MAINTENANCE 12. Install the new filter cartridge (2). 13. Tighten the filter by hand until the seal touches the filter head. 14. Then, tighten the filter cartridge an additional to 3/4 of a turn. NOTICE: Overtightening can damage the filter seal. LEEN12T0473AA 15.
Page 349: Hydraulic Oil
7 - MAINTENANCE Hydraulic oil 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 350 7 - MAINTENANCE 10. Remove the hydraulic oil tank drain plug (3). 11. Drain the hydraulic oil into a suitable container and clean the tank. 12. Reinstall and tighten the drain plug. RAIL15TLB0179AA Filling 13. Fill hydraulic tank with YDRAULIC until the level reaches RANSMISSION REMIUM...
Page 351 7 - MAINTENANCE 18. Check the hydraulic oil level. 19. The oil must reach the middle of the gauge (4). If necessary, add more oil. NOTICE: Even when its level is insufficient, a small quan- tity of hydraulic oil remains in the lower part of the gauge. This does not mean that the level is sufficient.
Page 352: Power Shuttle Transmission - Oil Change
7 - MAINTENANCE Power shuttle transmission - Oil change 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion.
Page 353 7 - MAINTENANCE 18. Engage the parking brake. 19. Check the oil level again by means of the dipstick and, if necessary, add more oil. 20. Lower and lock the engine hood. 21. Remove the safety support strut and lower the loader attachment.
Page 354: Power Shuttle Transmission - Oil Filter Replacement
7 - MAINTENANCE Power shuttle transmission - Oil filter replacement 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion.
Page 355: Power Shuttle Transmission - Screen Filter Cleaning
7 - MAINTENANCE Power shuttle transmission - Screen filter cleaning 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion.
Page 356 7 - MAINTENANCE Oil specification and capacities Use H YDRAULIC RANSMISSION REMIUM Capacities: 2WD Total System 18.5 L (19.5 US qt), Re- fill with or without filter change 11.9 L (12.6 US qt). Capacities: 4WD Total System 20.8 L (22.0 US qt), Re- fill with or without filter change 14.4 L (15.2 US qt).
Page 357: Powershift Transmission - Oil Change
7 - MAINTENANCE Powershift transmission - Oil change 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion.
Page 358 7 - MAINTENANCE 15. Reinstall the dipstick (1). 16. Check the oil level by means of the dipstick, and add additional oil if necessary. LEEN11T0356AA 17. Drive the machine for a few minutes in first and second gear. Then stop the machine with the engine running, and the direction-of-travel lever and the transmission gearshift lever in the neutral position.
Page 359: Powershift Transmission - Oil Filter Replacement
7 - MAINTENANCE Powershift transmission - Oil filter replacement 1. Move the machine to a level and firm surface. 2. Raise the loader attachment and install the safety sup- port strut. 3. Place the backhoe attachment in the road travel posi- tion.
Page 360: Front Axle Fluid - Four-Wheel Drive (4Wd)
7 - MAINTENANCE Front axle fluid - Four-Wheel Drive (4WD) 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and gearshift lever in the neutral position.
Page 361 7 - MAINTENANCE 7. When the oil has drained, manually turn the wheel until the hole of the plug (1) is in horizontal position. 8. Fill the reduction gear with new Ambra Transaxle Fluid (MS-1317) through the hole (1) until the level reaches the hole.
Page 362: Rear Axle
7 - MAINTENANCE Rear axle Rear axle - Oil change 1. Move the machine to a level and firm surface. 2. Lower the loader attachment to the ground. 3. Place the backhoe attachment in the road travel posi- tion. 4. Place the direction-of-travel lever and the gearshift lever in the neutral position.
Page 363: Machine Inspection And Cleaning
7 - MAINTENANCE Machine inspection and cleaning Inspection Externally check the machine and its working attach- ments, checking for possible breaks or damage of the components or the structure. If you find any problems, contact an authorized work- shop to have the necessary repairs carried out. Replace the damaged or excessively worn parts with original spare parts.
Page 364: Brake Pedal Lever - Greasing
7 - MAINTENANCE Brake pedal lever - Greasing 1. Grease the brake pedal levers (1) by introducing the new clean grease and expelling the exhaust grease until the new grease starts coming out. 2. Clean all the grease that come out with a cloth. LEEN11T0411AA_1 Grease specifications Use M...
Page 365: Hydraulic Cylinders
7 - MAINTENANCE Hydraulic cylinders The hydraulic cylinders must not show any kind of leaks. The cylinder rods must have a slightly oily aspect in order to guarantee a long life and a good operation. Cylinder tightness A tightness check must be performed after a certain working period and when the hydraulic system is at nor- mal operating temperature.
Page 366: Alternator - Check
7 - MAINTENANCE Alternator - check NOTICE: Do not use steam cleaning devices nor cleaning solvents to clean the alternator. Have the alternator (1) checked by your Dealer. NOTE: Make sure the terminal protectors are correctly in- stalled. RAIL15TLB0041AA 7-114...
Page 367: Every 1500 Hours Of Operation Or Annually
7 - MAINTENANCE Every 1500 hours of operation or annually Engine breather filter Change the engine breather filter every 1500 h or annually, whichever comes first. 1. With cold engine, remove the ventilation pipe (1) from the cover (2) after removing the retaining clamp. 2.
Page 368: Every 3000 Hours
7 - MAINTENANCE Every 3000 hours Diesel Exhaust Fluid (DEF)/AdBlue® supply module filter 1. To access the supply module, remove the corner shroud. RAIL15TLB0023AA 2. Remove the DEF/AdBlue® tank cover plate. RAIL15TLB0022AA 3. Remove the fuel tank step plate. RAIL15TLB0020AA 7-116...
Page 369 7 - MAINTENANCE 4. Remove the three bolts from the panel to the right-hand side of the step, in front of the rear tire. RAIL15TLB0019AA 5. These bolts attach to a bracket that hold the supply module in place. RAIL15TLB0018AA 7-117...
Page 370 7 - MAINTENANCE NOTICE: Pay attention to the location of each tube in the supply module. Also take care not to damage or loosen the connectors on the lines. Tubes and connector that have damage or fit loosely will not connect properly to the supply module causing leaks and issues with the Selective Cata- lyst Reduction (SCR) system.
Page 371 7 - MAINTENANCE 8. Remove the equalizing element. RAIL13GEN0027AA 9. Remove the filter tool from the new filter element. Check the color of the filter (Grey or Black). Based on the color of your filter element, insert the correct end of the filter tool into the filter element.
Page 372 7 - MAINTENANCE 12. Clean the supply module filter housing and threads with distilled water. RAIL13GEN0031AA 13. Oil the O-rings on the new filter element. Insert the filter element fully into the supply module. RAIL13GEN0032AA 14. Install the new equalizing element. RAIL13GEN0027AA 15.
Page 373 7 - MAINTENANCE 16. Connect the three connections back to the supply module. you will hear them snap in place. RAIL14TLB0968BA 17. Install the bracket and secure the supply module in place. RAIL15TLB0018AA RAIL15TLB0019AA 7-121...
Page 374: Every 4000 Hours
7 - MAINTENANCE Every 4000 hours Engine coolant CAUTION Burn hazard! Hot coolant can spray out if you remove the filler cap while the system is hot. After the system has cooled, turn the filler cap to the first notch and wait for all pressure to release before proceeding. Failure to comply could result in minor or moderate injury.
Page 375 7 - MAINTENANCE NOTE: In some situations air pockets in the coolant system may prevent you from filling the system to capacity. If this occurs remove the de-aeration valve cap this allows the air to escape during the fill procedure. The de-aeration valve cap is on the top right-hand side of the engine below the air filter housing.
Page 376: As Required
7 - MAINTENANCE As required Drive belt Replace the fan drive belt as needed. Removal 1. Remove the air conditioning compressor belt, if equipped. 2. Loosen the lower alternator bolt (2). 3. Loosen the pivot bolt (1). 83118121 4. Loosen the adjustment bolt lock nut (1). 5.
Page 377 7 - MAINTENANCE Install 1. Route the drive belt on the pulleys as shown. 83118087 2. Setting and securing the fan belt tension: A. Turn the adjustment bolt (1) clockwise, until the pivot bolt (2) is at the end of the tension bracket slot (3).
Page 378: Air-Conditioning Compressor Drive Belt
7 - MAINTENANCE Air-conditioning compressor drive belt 1. Visually check the condition of the belt (1). Replace it if it is worn or damaged. 2. To release the belt, loosen the mounting hardware of the tensioner (3) and loosen the tensioner adjusting screw (2).
Page 379: Turbocharger - Check
7 - MAINTENANCE Turbocharger - Check NOTICE: Observe the following recommendations on the adequate lubrication to avoid serious damage to the tur- bocharger bearing. The following procedure must be observed in order to prevent the turbocharger bearings from deteriorating. 1. Disconnect the inlet and outlet oil pipes from the tur- bocharger and pour some clean engine oil into the oil inlet port, taking care that no contaminants enter the turbocharger.
Page 380: Fuel System Bleeding
7 - MAINTENANCE Fuel system bleeding WARNING Pressurized system! Only use the bleed screw to bleed air from the fuel system. DO NOT loosen the fuel or injector lines to bleed air. Injury or damage can occur. Fuel or injector lines are under very high pressure. Failure to comply could result in death or serious injury.
Page 381: Wheels And Tires
7 - MAINTENANCE Wheels and tires NOTE: Depending on the manufacturing date of your machine the front wheel mounting hardware may be either lug nuts or bolts with washers. Check the wheel torque that is applicable to your machine. NOTICE: Small variations in the friction force between the wheel and the mounting hardware, such as lubricant, lack of lubricant, paint, surface rust, thread variations, etc., will cause large variations in the clamping force.
Page 382 7 - MAINTENANCE Rear wheel 1. Tighten the five mounting nuts in the sequence shown until the wheel is snug against the axle hub. 2. Tighten the nuts in sequence to a torque of 136 N·m (100 lb ft). 3. Tighten the nuts a second time, in sequence, to a torque of 271 N·m (200 lb ft).
Page 383 7 - MAINTENANCE 2. Periodical checks should be made to ensure the correct toe-in is maintained. Adjustment 3. Place the machine on a level ground presenting no el- ements which could affect adjustments. 4. Steer the wheels to the front. 5.
Page 384: Hydraulic System - Release Pressure
7 - MAINTENANCE Hydraulic system - Release pressure 1. Park the machine on firm level ground. 2. Put all transmission controls in the Neutral position. 3. Engage the parking brake. 4. Lower the bucket to the ground but do not apply down pressure;...
Page 385 7 - MAINTENANCE 15. Rotate the loader control joystick in one complete cir- cle, stopping in the neutral (center) position. RAIL18TLB0403BA 16. If applicable, operate the bucket control switch. 17. Turn the key switch to the Off position. Releasing hydraulic pressure on machines with mechanical backhoe controls 1.
Page 386 7 - MAINTENANCE 13. Rotate the loader control joystick in one complete cir- cle, stopping in the neutral (center) position. RAIL18TLB0403BA 14. If applicable, operate the bucket control switch. 15. Turn the key switch to the Off position. Hydraulic fittings and lines - Replace 1.
Page 387: Bulbs
7 - MAINTENANCE Bulbs NOTICE: Never touch a halogen bulb with your fingers. Always use a clean cloth when handling halogen bulbs. Operator’s compartment light 1. Remove the lens (1) unscrewing it by turning 90° through its central slot. 2. Remove the bulb (2) and install a new bulb. 3.
Page 388 7 - MAINTENANCE Front, side, and rear work lights 1. Remove the screws and take off the light assembly (1). 2. Remove the bulb and install a new bulb. 3. Install the light assembly and the screws. Bulb wattage: 55 W LEEN12T0706AA Rotating beacon (optional) 1.
Page 389: Fuses And Relays - Powershift
7 - MAINTENANCE Fuses and relays – Powershift NOTICE: NEVER replace a fuse with a fuse of a different rating. Main fuse and relay panel Remove the main fuse cover panel from the front right- hand side console. The vehicle diagnostic connector (1) and the four pin FleetForce™...
Page 390 7 - MAINTENANCE Fuses Fuse No. Rating Function 15 A Rear windshield wiper and rear windshield washer 7.5 A +15 Antitheft 10 A 4wd, automatic manual, TRAX, cut transmission and differential block 15 A Instrument power supply, switches lamps, seat 15 A Air-conditioning 15 A...
Page 391 7 - MAINTENANCE RAIL14TLB1180GA 7-139...
Page 392 7 - MAINTENANCE Fuse and relay module Remove the side instrument cluster panel to expose the mini relay and fuse panel. NOTE: Four-Wheel Steer (4WS) machines will have less relays then what is shown. RAIL15TLB0258BA RAIL15TLB0136AA Fuse or relay reference Designation K225 Parking brake relay X-225 (not applicable to 4WS)
Page 393 7 - MAINTENANCE Engine compartment fuse and relay panel Open the engine hood and locate the fuse and relay panel on the left-hand side of the engine. • X-449 Fuse panel (1) • X-448 Fuse and relay panel (2) • Glow-Plug Control Unit (GCU) (3) •...
Page 394 7 - MAINTENANCE If the machine is equipped with Air-Conditioning (A/C). On the right-hand side of the engine near the alternator is a 40 A in-line harness blower fuse (F953/X-953). RAIL16TLB0369BA Main power fuse module Open the battery compartment door and locate the 80 A main power fuse.
Page 395: Fuses And Relays - Power Shuttle
7 - MAINTENANCE Fuses and relays – Power shuttle NOTICE: NEVER replace a fuse with a fuse of a different rating. Main fuse and relay panel Remove the main fuse cover panel from the front right- hand side console. The vehicle diagnostic connector (1) and the four pin FleetForce™...
Page 396 7 - MAINTENANCE Fuses Fuse No. Rating Function 15 A Rear windshield wiper and rear windshield washer 7.5 A Fuel shut off, +15 antitheft, key switch +15 ECU, reset parking brake 10 A Stop lights switch 15 A Instrument side panel, switches lamps 15 A Air conditioning 15 A...
Page 397 7 - MAINTENANCE RAIL14TLB1183GA 7-145...
Page 398 7 - MAINTENANCE Side relay and fuse module Remove the side instrument cluster panel to expose the mini relay and fuse panel. RAIL15TLB0258BA RAIL15TLB0138AA Fuse or relay reference Designation K225 Parking brake relay X-225 K230 Hand hammer relay X-230 K232 Glide Ride™...
Page 399 7 - MAINTENANCE Engine compartment fuse and relay panel Open the engine hood and locate the fuse and relay panel on the left-hand side of the engine. • X-449 Fuse panel (1) • X-448 Fuse and relay panel (2) • Glow-Plug Control Unit (GCU) (3) •...
Page 400 7 - MAINTENANCE If the machine is equipped with Air-Conditioning (A/C). On the right-hand side of the engine near the alternator is a 40 A in-line harness blower fuse (F953/X-953). RAIL16TLB0369BA Main power fuse module Open the battery compartment door and locate the 80 A main power fuse.
Page 401: Telematics System Fuses (If Equipped)
7 - MAINTENANCE Telematics system fuses (if equipped) NOTE: If your machine is equipped with a Telematics system, your machine will have two additional 5 A fuse locations. 1. The first in-line fuse location. A. Remove the side instrument cluster panel. B.
Page 402: Battery Removal And Installation
7 - MAINTENANCE Battery removal and installation WARNING Electrical shock hazard! Do not reverse battery terminals. Connect positive cable ends to positive terminals (+) and negative cable ends to negative terminals (-). Failure to comply could result in death or serious injury. W0262A WARNING Battery gas can explode!
Page 403 7 - MAINTENANCE 9. Remove the terminal covers and disconnect the cables, first from the negative terminal (3) then the positive ter- minal (4). 10. Remove the nuts and washers (5), the clamping bar (6) and the battery (7). 11. Install the battery (7). 12.
Page 404: Telescopic Dipper (If Equipped)
7 - MAINTENANCE Telescopic dipper (if equipped) 1. Ensure the drain port (1) in the end of the dipper is kept clear to prevent accumulation of water inside the unit. 2. Check the hole for hydraulic oil traces, which would indicate the presence of a pressure loss in the cylinder.
Page 405: Bucket Teeth
7 - MAINTENANCE Bucket teeth Bucket - Loader attachment 1. Move the machine to a level and firm ground. 2. Position the loader bucket so that the bucket teeth can be replaced. 3. Place the direction-of-travel lever and gearshift lever in neutral position.
Page 406: Loader Bucket - Self-Leveling Adjustment
7 - MAINTENANCE Loader bucket - Self-leveling adjustment 1. The self-leveling linkage mounted on the right hand loader arm and frame automatically controls the angle of the loader bucket during the raising cycle of the lift arms to maintain a constant bucket level. There is no self-leveling during the lowering cycle.
Page 407 7 - MAINTENANCE Return-to-dig system 1. Return to dig is an electrically activated feature which enables the operator to automatically return the bucket to a level digging position for a further work cycle with one simple movement of the loader control lever (3). 2.
Page 408: Disable Parking Brake
7 - MAINTENANCE Disable parking brake For disabled machines, disable the parking brake whenever the parking brake fails to disengage. 1. Chock the wheels to prevent movement. 2. Remove the mat and floor plate. 3. Locate the solenoid block for the parking brake on the transmission.
Page 409 7 - MAINTENANCE 10. To enable the parking brake: A. Slowly loosen and remove the two bolts that hold the solenoid block in position. Grease trapped in the parking brake will come out under the block. B. Confirm that the three O-rings are in the correct position and that all surfaces are free of contam- ination.
Page 410: Storage
7 - MAINTENANCE STORAGE Machine storage If the machine is to be in storage for more than 30 days, park the machine inside a building. If a building is not available, park the machine in a dry area on planks and cover the machine with a waterproof covering. Geographic, environmental and actual storage conditions make it difficult to follow a set storage procedure for all areas and conditions.
Page 411: Preparation For Use After Storage
7 - MAINTENANCE Preparation for use after storage Do not start the engine until Steps 1 through 12 have been done. 1. Change the fuel filters and fill the fuel take if required. 2. Tighten the cooling system drain valves. 3.
Page 412 7 - MAINTENANCE 7-160...
Page 413: Troubleshooting
8 - TROUBLESHOOTING TROUBLESHOOTING###_8_### FAULT CODE RESOLUTION Troubleshooting Often failures are due to improper use or to an irregular maintenance of the machine. In case of failure, it is recommended to read the relevant chapter in the manual. In case no failure cause can be determined or if you are not able to eliminate the problem, consult the Service De- partment.
Page 414 8 - TROUBLESHOOTING Correction Here it is explained how to detect and eliminate the cause of the problem.
Page 415: Engine - Troubleshooting
8 - TROUBLESHOOTING Engine - Troubleshooting Problem Possible Cause Correction The engine does not start. Partially discharged batteries. Check, charge the batteries and, if neces- sary, replace them. Corroded or loose connections to the bat- Clean, inspect, tighten the nuts and, if nec- tery terminals.
Page 416 8 - TROUBLESHOOTING Problem Possible Cause Correction Noisy cylinder pin due to excessive clear- Contact your dealer. ance in hub and connecting rod bushing. Bushings free in their seat on the connect- ing rod. Ticking due to noisy distribution. Contact your dealer. Anomalous engine Contact your dealer.
Page 417: Starter Motor - Troubleshooting
8 - TROUBLESHOOTING Starter motor - Troubleshooting Problem Possible Cause Correction The starter motor does Too low specific density and battery level. Inspect the battery. not run. Poor ignition switch circuit connection or Replace the wiring harness and the ignition contact.
Page 418: Alternator - Troubleshooting
8 - TROUBLESHOOTING Alternator - Troubleshooting Problem Possible Cause Correction Not recharged. Recharge circuit interrupted (warning lamp, Check the connections of the recharge cir- fuse, connector, etc.). cuit, clean and tighten the alternator and battery terminals. Voltage regulator inefficient. Replace alternator. Rotor winder interrupted.
Page 419: Transmission - Troubleshooting
8 - TROUBLESHOOTING Transmission - Troubleshooting Problem Possible Cause Correction The vehicle does not Control valve supply problem. Check and, if necessary, replace the con- move. trol valves. Damaged connections of transmission and Repair and, if necessary, replace the wiring vehicle wiring harness.
Page 420 8 - TROUBLESHOOTING Problem Possible Cause Correction Damaged connections of transmission and Repair and, if necessary, replace the con- vehicle wiring harness (only for powershift nections (only for powershift models). models). Damaged logic of EGM/ECU gearshift Replace the EGM/ECU (only for powershift electronic control (only for powershift mod- models).
Page 421 8 - TROUBLESHOOTING Problem Possible Cause Correction Damaged synchronizers (only for power Replace the synchronizers (only for power shuttle models). shuttle models). Lack of 4WD power Damaged 4WD connection assembly. Replace the 4WD connection assembly. transmission. Hydraulic system fault. Repair the hydraulic system. Damaged control valve.
Page 422: Axles - Troubleshooting
8 - TROUBLESHOOTING Axles - Troubleshooting Problem Possible Cause Correction Wheel vibrations. Incorrect installation. Correct the installation. Inspect and repair the axle. Defective axle. Wrong weight distribution. Distribute the weight differently. Overload. Remove the excessive load. Incorrect tire rotation radius. Replace the tire or adjust pressure on both tires.
Page 423 8 - TROUBLESHOOTING Problem Possible Cause Correction Vibrations during travel. Incorrect installation. Correct the installation. Inspect and repair. Defective axle. Wrong weight distribution. Distribute the weight differently. Bent or broken axle shaft. Replace the axle beam. Break towards the outer Excessive gear load compared to the pre- Replace the bevel gear.
Page 424 8 - TROUBLESHOOTING Problem Possible Cause Correction Worn or scratched washer Replace all scratched washers and those Insufficient lubrication. surfaces. with a thickness by 0.1 mm (0.004 in)lower than the new ones. Incorrect lubrication. Contaminated lubri- Use proper lubricant, fill up to the correct cant.
Page 425: Steering System - Troubleshooting
8 - TROUBLESHOOTING Steering system - Troubleshooting Problem Possible Cause Correction No steering or excessive Incorrect oil level in the tank. Fill with the correct oil type and quantity. effort required to steer. Check for loose connections or damaged lines. Bleed the system. Air in the system.
Page 426: Hydraulic Systems - Troubleshooting
8 - TROUBLESHOOTING Hydraulic systems - Troubleshooting Problem Possible Cause Correction All circuits fail to operate. Pump drive inoperative. Check and repair as necessary. Low oil level. Check the level and top up. Restricted pump suction line. Inspect the suction line and the tank and repair as necessary.
Page 427: Loader Attachment - Troubleshooting
8 - TROUBLESHOOTING Loader attachment - Troubleshooting Problem Possible Cause Correction Valve spool leaking. The lifting circuit fails to Inspect the spool and check it for wear or operate, is slow or loses scratches. power. Cylinder seals leaking or cylinder barrel Inspect and reseal the cylinder.
Page 428: Backhoe Attachment - Troubleshooting
8 - TROUBLESHOOTING Backhoe attachment - Troubleshooting Problem Possible Cause Correction The lifting system is The lifting circuit relief valve is stuck open, Test the pressure of the lifting circuit relief inoperative, is too slow, set to a too low value or there is a leak in valve.
Page 429: Swing - Troubleshooting
8 - TROUBLESHOOTING Swing - Troubleshooting Problem Possible Cause Correction Right or left swing is The swing circuit relief valves are not seat- Test the swing circuit relief valve. inoperative, is too slow or ing, set to a too low value or there is a leak loses power.
Page 430: Hydraulic Pump - Troubleshooting
8 - TROUBLESHOOTING Hydraulic pump - Troubleshooting Problem Possible Cause Correction Noisy system. Worn or damaged pump gears or pressure Make a hydraulic pump performance test. plates. Aeration: air entering the systems at: suc- Make a hydraulic pump performance test. tion tube, pump shaft, fittings or cylinder ring nuts.
Page 431: Electrical Systems - Troubleshooting
8 - TROUBLESHOOTING Electrical systems - Troubleshooting Problem Possible Cause Correction The electrical system is Loose or oxidized battery connections. Check that the battery voltage with open inoperative. circuit is at least 12.6 V. Clean and tighten the connections. Sul- Check the electrolyte level and density.
Page 432: Cab - Troubleshooting
8 - TROUBLESHOOTING Cab - Troubleshooting Problem Possible Cause Correction Dust enters the cab. Improper seal around the filter. Check the seal condition. Restricted filter. Clean or replace the filter. Defective filter. Replace the filter. The blower motor Restricted air filter(s). Clean or replace the filter(s).
Page 433: Air-Conditioning System - Troubleshooting
8 - TROUBLESHOOTING Air-conditioning system - Troubleshooting Problem Possible Cause Correction The system does not cool. Condenser obstructed. Clean the radiator, the oil cooler and the condenser. Insufficient coolant. Check sight glass for bubbles. Consult your Dealer. Belt slipping or damaged. Check the automatic belt tensioner and belt condition.
Page 434: Alarm(S)
8 - TROUBLESHOOTING ALARM(S) Display screen messages Display Description Action Warning machine fault is present Contact your dealer for assistance. Stop the machine a critical error is present. Contact your dealer for assistance Engine de-rate Contact your dealer for assistance. Parking brake not released Disengage the parking brake.
Page 435 8 - TROUBLESHOOTING Display Description Action Controller Area Network (CAN) malfunction Contact your dealer for assistance. Fuel level sensor or transmission temperature Contact your dealer for assistance. sensor error Throttle fault Contact your dealer for assistance. Battery voltage too high or too low Contact your dealer for assistance.
Page 436 8 - TROUBLESHOOTING 8-24...
Page 437: Specifications
9 - SPECIFICATIONS SPECIFICATIONS###_9_### Capacities - B95C, B95C LR, and B95C TC Engine crank case Specification: 10W-40( API CJ-4) NGINE YNTHETIC Capacity: With filter change 8.0 L (8.5 US qt) Fuel tank Specification: ASTM D975 G . 2-D S15 (No. 2 diesel)
Page 438 9 - SPECIFICATIONS Front drive axle - Four-Wheel drive (4WD) Specification: 80W-140 REMIUM RANSAXLE Capacity: Differential 6.5 L (6.9 US qt) Each planetary hub 0.7 L (0.7 US qt) Rear axle (differential and hubs) Specification: 80W-140 REMIUM RANSAXLE Capacity: 21.2 L (22.4 US qt)
Page 439: Capacities - B110C
9 - SPECIFICATIONS Capacities – B110C Engine crank case Specification: 10W-40( API CJ-4) NGINE YNTHETIC Capacity: With filter change 8.0 L (8.5 US qt) Fuel tank Specification: ASTM D975 G . 2-D S15 (No. 2 diesel) RADE Capacity: 131.0 L (34.6 US gal) Emissions fluid tank Specification: (DEF)/A...
Page 440 9 - SPECIFICATIONS Front drive axle - Four-Wheel drive (4WD) Specification: 80W-140 REMIUM RANSAXLE Capacity: Differential 6.5 L (6.9 US qt) Each planetary hub 0.7 L (0.7 US qt) Rear axle (differential and hubs) Specification: 80W-140 REMIUM RANSAXLE Capacity: 21.2 L (22.4 US qt)
Page 441: Engine
9 - SPECIFICATIONS Engine B95C, B95C LR, and B95C TC Model Diesel, F5BFL413B*B003, Tier 4B (Final) emissions compliant (base engine F5BFL413A*B007) Type Four cylinder, turbocharged Firing order 1-3-4-2 Bore and stroke 99 mm x 110 mm( 3.90 in x 4.33 in) Displacement 3.4 l (207.5 in³)
Page 442 9 - SPECIFICATIONS B110C Model Diesel, F5BFL413A*B006, Tier 4B (Final) emissions compliant (base engine F5BFL413A*B007) Type Four cylinder, turbocharged Firing order 1-3-4-2 Bore and stroke 99 mm x 110 mm( 3.90 in x 4.33 in) Displacement 3.4 l (207.5 in³) Compression ratio 17 to 1 Fuel injection...
Page 443: Powertrain
9 - SPECIFICATIONS Powertrain TRANSMISSION - POWER SHUTTLE Model CARRARO TLB2 Type (4x4) 4 forward and 4 reverse travel gears Torque converter ratio 2.38 Transmission ratios: 1st gear forward travel 5.603:1 — reverse travel 4.643:1 2nd gear forward travel 3.481:1 — reverse travel 2.884:1 3rd gear forward travel 1.585:1 —...
Page 444: Brakes And Controls - General Specification
Brakes and controls - General specification FRONT AXLES FRONT AXLE Model CNH 26.17 Type steering REAR AXLES REAR AXLE Model (B95C - B95C TC - B95C LR) CARRARO 28.44 Model (B110C) CARRARO 28.50 Type rigid Differential lock electrical BRAKES SERVICE BRAKES Type Hydraulic foot operated, two disc per side.
Page 445: Hydraulics
9 - SPECIFICATIONS Hydraulics GEAR PUMP 72 kW - 97 HP PUMP (B95C - B95CTC - B95CLR) Model CASAPPA Type double gear pump Flow rate 35.427 + 35.427 cm3/rev (2.16 + 2.16 in3/rev) 82 kW - 110 HP PUMP (B110C)
Page 446: Front Counterweight
9 - SPECIFICATIONS Front counterweight COUNTERWEIGHT Small 159 kg (351 lb) Medium 326 kg (719 lb) Large 442 kg (974 lb) 9-10...
Page 447: Noise And Vibration Levels
9 - SPECIFICATIONS Noise and vibration levels Noise level Internal noise level (LpA) 77 dB External noise level (LwA) (B95C - B95C TC - B95C LR) 102 dB External noise level (LwA) (B110C) 103 dB Vibration level inside the cab Upper limbs level lower than 2.5 m/s²...
Page 448: Buckets
9 - SPECIFICATIONS Buckets Loader buckets 0.88 m³ (31.08 ft³) Type 1 m³ (35.3 ft³) standard 6 x 1 (with forks) 4 x 1 standard Heaped 0.88 m³ (31.08 ft³) 1.0 m³ (35.3 ft³) 1.0 m³ (35.3 ft³) 1.0 m³ (35.3 ft³) capacity Width 2250 mm (88.58 in)
Page 449: Tires
9 - SPECIFICATIONS Tires Inflating pressure and allowed carrying capacity table NOTE: The following tables give the approximate carrying capacity at the indicated tire pressures when traveling at a maximum speed of 30 km/h (19 mph). INFLATION PRESSURE bar (psi) (21.7) (29.0) (31.9)
Page 450 9 - SPECIFICATIONS INFLATION PRESSURE bar (psi) (17.4) (20.3) (21.7) (27.5) (31.9) Tire size Profile Rear 16.9–28 EZ MAX LOAD PER TIRE kg (lb) 2300 2490 2620 3110 3410 (5070) (5489) (5776) (6856) (7517) INFLATION PRESSURE bar (psi) (17.4) (20.3) (21.7) (27.5) (31.9)
Page 451: Dimensions And Performance
9 - SPECIFICATIONS Dimensions and performance Dimensions LEEN12T0742FA Front tires 12.5/18 Rear tires 18.4–26 Standard loader bucket 1 m³ (35.31 ft³) Standard backhoe bucket 914 mm (36.0 in) Overall machine length 7030 mm (276.4 in) Loader bucket reach 1870 mm (73.6 in) Wheel base 2175 mm (86.0 in) 2985 mm (117.5 in)
Page 452 9 - SPECIFICATIONS Loader attachment performance B95C TC with standard bucket 1 m³ (35.3 ft³) LEEN12T0743FA_1 Maximum height/dimensions Maximum height of loader bucket pin/pivot Maximum dumping height Digging depth Loader attachment reach when raised in dumping position α. Angle of lowered closed bucket β.
Page 453 9 - SPECIFICATIONS B95C and B110C with standard bucket 0.88 m³ (31.1 ft³) LEEN12T0743FA_1 Maximum height/dimensions Maximum height of loader bucket pin/pivot Maximum dumping height Digging depth Loader attachment reach when raised in dumping position α. Angle of lowered closed bucket β.
Page 454 9 - SPECIFICATIONS B95C and B110C with standard bucket 1 m³ (35.3 ft³) LEEN12T0743FA_1 Maximum height/dimensions Maximum height of loader bucket pin/pivot Maximum dumping height Digging depth Loader attachment reach when raised in dumping position α. Angle of lowered closed bucket β.
Page 455 9 - SPECIFICATIONS B95C and B110C with 4x1 bucket 1 m³ (35.3 ft³)) LEEN12T0743FA_1 Maximum height/dimensions Maximum height of loader bucket pin/pivot Maximum dumping height Digging depth Loader attachment reach when raised in dumping position α. Angle of lowered closed bucket β.
Page 456: Dimensions And Performance - 6 In 1 Bucket
9 - SPECIFICATIONS Dimensions and performance – 6 in 1 bucket B95C and B110C LEEN12T0744FA Front counterweight Maximum height of loader bucket pin/pivot with lifted forks Fork maximum height Height of loader bucket pin/pivot with lowered forks Fork reach when raised...
Page 457: Backhoe Attachment Performance
9 - SPECIFICATIONS Backhoe attachment performance B95C, B95C TC, and B110C (with short standard dipper) LEEN12T0745FA_1 Front tires 11L-16F3 Rear tires 17.5L-24 Maximum digging height 5443 mm (214.3 in) Maximum height at full load 3613 mm (142.2 in) Maximum digging depth 4426 mm (174.3 in)
Page 458 9 - SPECIFICATIONS B95C LR and B110C (with long standard dipper) LEEN12T0745FA_1 Front tires 11L-16F3 Rear tires 17.5L-24 Maximum digging height 5634 mm (221.8 in) Maximum height at full load 3823 mm (150.5 in) Maximum digging depth 4727 mm (186.1 in) Digging depth [Length = 2438.4 mm (96.00 in)]...
Page 459 9 - SPECIFICATIONS B95C, B95C TC, and B110C (with short telescopic dipper) LEEN12T0745FA_1 Retracted dipper Front tires 11L-16F3 Rear tires 17.5L-24 Maximum digging height 5547 mm (218.4 in) Maximum height at full load 3737 mm (147.1 in) Maximum digging depth 4586 mm (180.6 in)
Page 460 9 - SPECIFICATIONS B95C LR and B110C (with long telescopic dipper) LEEN12T0745FA_1 Retracted dipper Front tires 11L-16F3 Rear tires 17.5L-24 Maximum digging height 5635 mm (221.9 in) Maximum height at full load 3826 mm (150.6 in) Maximum digging depth 4735 mm (186.4 in) Digging depth [Length = 2438.4 mm (96.00 in)]...
Page 461: Backhoe Attachment Lifting Capacity
9 - SPECIFICATIONS Backhoe attachment lifting capacity Lifting capacity - B95C and B95CTC (Short dipper – 14ft in-line cylinder) Lifting capacity in normal operating mode - SAE rated The following table reports the lifting capacities of the dip- per “A” and the boom “B”.
Page 462 9 - SPECIFICATIONS Lifting capacity - B95CLR and B110C (Long dipper – 15ft in-line cylinder) Lifting capacity in normal operating mode - SAE rated The following table reports the lifting capacities of the dip- per “A” and the boom “B”. NOTE: The capacities indicated may slightly vary from one machine to another, according to the accessories mounted, the pressure settings and the market require-...
Page 463: 10 - Accessories
10 - ACCESSORIES 10 - ACCESSORIES###_10_### Mechanical loader bucket quick coupler It is possible to install a quick coupler (1) for the loader bucket on the loader attachment, using the standard mounting pins (2). Quick removal and installation of the loader bucket Make sure the bucket to be installed is in a safe area, on a level and firm ground and with the upper pins in place.
Page 464: Mechanical Backhoe Bucket Quick Coupler
10 - ACCESSORIES Mechanical backhoe bucket quick coupler WARNING Equipment failure could cause accident or injury! Use only authorized auxiliary hydraulic attachments. Always read and understand the manual or in- structions supplied by the manufacturer to avoid injury or damage. Understand the operation and safety instructions before you attach, remove, or operate the attachment.
Page 465 10 - ACCESSORIES Installing an attachment with a mechanical quick coupler 1. Make sure that all unauthorized workers or bystanders are away from the machine. 2. Position the backhoe so that you will be able to extend the backhoe and reach the lower bucket pin (4). NOTICE: The bucket must have a pin in the maximum power position (3) otherwise you will not be able to attach the bucket.
Page 466: Backhoe Attachment Auxiliary Hydraulic Tools
10 - ACCESSORIES Backhoe attachment auxiliary hydraulic tools WARNING Equipment failure could cause accident or injury! Use only authorized auxiliary hydraulic attachments. Always read and understand the manual or in- structions supplied by the manufacturer to avoid injury or damage. Understand the operation and safety instructions before you attach, remove, or operate the attachment.
Page 467: Hand Held Auxiliary Hydraulic Tools
10 - ACCESSORIES Hand held auxiliary hydraulic tools WARNING Equipment failure could cause accident or injury! Use only authorized auxiliary hydraulic attachments. Always read and understand the manual or in- structions supplied by the manufacturer to avoid injury or damage. Understand the operation and safety instructions before you attach, remove, or operate the attachment.
Page 468: Backhoe Attachment Safety Valves
10 - ACCESSORIES Backhoe attachment safety valves The function of the safety valves (1) is to prevent the at- tachment from falling because of oil leaks in the control valve (spool in neutral) or hoses accidentally breaking, as well as to guarantee a smooth and controlled lowering of the attachment in the event of a hose or pipe accidentally breaking.
Page 469: Reversible Stabilizer Pads
10 - ACCESSORIES Reversible stabilizer pads These stabilizer pads are intended for use in the street or on the job site. They may be turned around 180°, as required. NOTICE: When these pads are used, there is a danger of them hitting the cab windows.
Page 470: Telematics - Overview With New Holland Fleetforce
Telematics - Overview with New Holland FleetForce™ NOTE: The NEW HOLLAND CONSTRUCTIONFleetForce™ website (www.newhollandfleetforce.com) will not be accessible until the NEW HOLLAND CONSTRUCTIONFleetForce™ subscription for this machine is registered by an authorized NEW HOLLAND CONSTRUCTION dealer. Contact an authorized NEW HOLLAND CONSTRUCTION dealer for details.
Page 471 ........7-7, 9-3 Capacities - B95C, B95C LR, and B95C TC ......7-5, 9-1 Checks at start-up and before each workshift (10 hours) .
Page 472 Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank - Drain fluid ..... . 7-32 Diesel Exhaust Fluid (DEF)/AdBlue®/ARLA tank - Filling ......7-31 Diesel Exhaust Fluid (DEF)/AdBlue®...
Page 473 Hot temperature operation ........4-10 Hydraulic cylinders .
Page 474 Swing - Troubleshooting ........8-17 Telematics - Overview with New Holland FleetForce™...
Page 475 Tire pressure ......... . . 7-55 Tires .
Page 476 New Holland dealer. © 2020 CNH Industrial America LLC. All Rights Reserved. New Holland is a trademark registered in the United States and many other countries, owned or licensed to CNH Industrial N.V., its subsidiaries or a liates.

This manual is also suitable for:

B95c tc B110c

New Holland B95C Original Instructions Manual

1 General Information

2 Safety Information

3 Controls and Instruments

4 Operating Instructions

5 Transport Operations

6 Working Operations

7 Maintenance

Every 1000 Hours

Every 1500 Hours of Operation or Annually

Every 3000 Hours

Every 4000 Hours

As Required

Storage

8 Troubleshooting

9 Specifications

10 - Accessories

Quick Links

Troubleshooting

Related Manuals for New Holland B95C

Summary of Contents for New Holland B95C