Lucent Technologies Stinger Compact Remote Getting Started Manual page 6

Atm dslam
Table of Contents

Advertisement

Contents
Checking the LPMs .......................................................................................... 2-14
Checking the cooling unit................................................................................ 2-15
Checking the power supply ............................................................................. 2-16
Chapter 3
Enclosure and Component Installation ...........................................3-1
Introduction ............................................................................................................. 3-1
Before you begin ...................................................................................................... 3-1
Stinger CR enclosure Mounting Hardware .............................................................. 3-2
Pole mounting hardware ................................................................................... 3-3
Cabinet mounting hardware.............................................................................. 3-4
Pedestal mounting hardware ............................................................................. 3-6
Inside rack mounting hardware ........................................................................ 3-6
Mounting the enclosure on a pole ........................................................................... 3-7
Center-mounting the enclosure on a pole......................................................... 3-8
Side-mounting the enclosure on a pole........................................................... 3-11
Mounting the enclosure on a wiring cabinet ......................................................... 3-13
Prepare the cabinet and install the mounting bracket..................................... 3-13
Mounting the enclosure .................................................................................. 3-14
Routing the cables out of the enclosure................................................................. 3-16
Routing the cables for cabinet mounting......................................................... 3-16
Routing the cables for pole mounting ............................................................. 3-17
Grounding the enclosure ....................................................................................... 3-18
Inspecting and replacing the door gasket ............................................................... 3-19
Installation and replacement of Stinger CR components....................................... 3-20
Slot numbering and module placement .......................................................... 3-21
Module installation and replacement for the COP slot.................................... 3-21
Installing and replacing LIMs........................................................................... 3-23
Installing and replacing LPMs.......................................................................... 3-25
Replacing the chassis cooling module.............................................................. 3-26
Replacing the external cooling fan .................................................................. 3-28
Replacing the power supply............................................................................. 3-30
Physical connections to the components ............................................................... 3-31
Connections to modules in the COP slot ......................................................... 3-31
vi
SHDSL 48-Port LIM................................................................................... 2-13
The T1-IMA LIM ....................................................................................... 2-14
The ±190Vdc power supply....................................................................... 2-16
The -48Vdc power supply ......................................................................... 2-17
Removing a module from the COP slot..................................................... 3-21
Installing a module in the COP slot........................................................... 3-22
Installing a LIM ......................................................................................... 3-23
Replacing a LIM ........................................................................................ 3-24
Installing an LPM ...................................................................................... 3-25
Replacing an LPM ..................................................................................... 3-25
PCMCIA slot .............................................................................................. 3-32
Gigabit Ethernet port................................................................................. 3-33
155Mbps optical port................................................................................. 3-33
10/100 Ethernet port ................................................................................ 3-34
Diagnostic port .......................................................................................... 3-35
Alarm input port ....................................................................................... 3-36
Modem port .............................................................................................. 3-37
The Stinger® Compact Remote ATM DSLAM Getting Started Guide
2-13
2-14
2-14
2-15
2-16
2-16
2-17
3-1
3-1
3-1
3-2
3-3
3-4
3-6
3-6
3-7
3-8
3-11
3-13
3-13
3-14
3-15
3-16
3-16
3-17
3-18
3-19
3-20
3-21
3-21
3-21
3-22
3-23
3-23
3-24
3-25
3-25
3-25
3-26
3-28
3-30
3-31
3-31
3-32
3-33
3-33
3-34
3-35
3-36
3-37

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Stinger Compact Remote and is the answer not in the manual?

Table of Contents