Lucent Technologies Stinger Compact Remote Getting Started Manual page 12

Figures
Figure 3-23 Connectors for modules in the COP slot ......................................... 3-31
Figure 3-24 Gigabit Ethernet connection to IP2000 module.............................. 3-33
Figure 3-25 155Mbps optical connection to the COP......................................... 3-34
Figure 3-26 Ethernet connection........................................................................ 3-34
Figure 3-27 Serial management connection for a stand-alone Stinger CR ATM
Figure 3-28 Connecting the door alarm to the ALARM input port.................... 3-37
Figure 3-29 Control module modem jumper connection .................................. 3-37
Figure 3-30 Connecting an LPM......................................................................... 3-38
Figure 3-31 LPM connector cable routing .......................................................... 3-40
Figure 3-32 IP2000 status lights ......................................................................... 3-42
Figure 3-33 COP status lights ............................................................................. 3-44
Figure 3-34 ADSL 48-port low-power LIM ........................................................ 3-45
Figure 3-35 The Stinger CR cooling unit ............................................................ 3-46
Figure 3-36 The Stinger CR ±190Vdc power supply .......................................... 3-47
Figure 4-1
Figure 4-2
Figure 4-3
Figure 4-4
Figure 4-5
Figure 5-1
Figure 5-2
Figure 5-3
Figure 5-4
Figure 5-5
Figure B-1
Figure C-1
Figure C-2
Figure C-3
Figure C-4
Figure C-5
Figure C-6
Figure C-7
Figure C-8
Figure C-9
Figure C-10 -48Vdc power supply cable ............................................................. C-19
Figure C-11 Door alarm connectors on the Stinger CR ATM DSLAM chassis .... C-20
Figure C-12 Door alarm cable for stand-alone operation ................................... C-21
Figure C-13 Optical Connectors .......................................................................... C-21
Figure D-1
Figure D-2
xii
DSLAM............................................................................................ 3-35
Serial management connection to a Stinger CR ATM DSLAM unit . 4-2
10/100 Ethernet connection ............................................................. 4-3
Gigabit Ethernet connection ............................................................. 4-4
Connection for internal modem........................................................ 4-5
Default netmask for class C IP address ............................................ 4-10
Chassis validation ID DIP switches ................................................... 5-2
Setting the Validation ID DIP switch................................................. 5-3
Slot-level CAC bandwidth calculations performed with default
settings ............................................................................................ 5-10
Port-level CAC sequence (performed only at provisioning time) ... 5-10
Factory-default validation ID setting on Compact Remote ............. 5-14
the Stinger OLIM............................................................................... B-2
Modem jumper cable and connectors ............................................... C-2
LPM 64-pin connector ...................................................................... C-4
Protection block cables ...................................................................... C-5
LPMs and related protection blocks .................................................. C-5
Protection block port assignments..................................................... C-6
Protection plug orientation example................................................. C-7
Stub cables for connection to the protection blocks........................ C-16
Protection block power connectors ................................................. C-18
-48Vdc stub-ended power cable...................................................... C-19
UL60950-21 capacitance specification .............................................. D-3
Warning labels for identification of Class 1 laser devices.................. D-7
The Stinger® Compact Remote ATM DSLAM Getting Started Guide
3-31
3-33
3-34
3-34
3-35
3-37
3-37
3-40
3-42
3-44
3-45
3-46
3-47
4-2
4-3
4-4
4-5
4-10
5-2
5-3
5-10
5-10
5-14
B-2
C-2
C-4
C-5
C-5
C-6
C-7
C-16
C-18
C-19
C-19
C-20
C-21
C-21
D-3
D-7