Table of Contents
Advertisement
4.8.14. SUB.SP - Setpoint value of slaved controller
Acronym
SUB.SP
PR.STP.1 (o PR.STP.2...PR.STP.192) SUBDUED SETPOINT ASSOCIATED TO
STEP se modalità"Programmatore semplificato"disattiva; o PR.STP.1...PR.
STP.16 SUBDUED SETPOINT ASSOCIATED TO STEP se modalità"Programm-
atore semplificato"attiva.
If the S.SP.EN function is enabled, the parameter shows and sets the setpoint value to be retransmitted as a percentage
of the controller setpoint value
EXAMPLE
If the setpoint of the main controller is 180°C and you want the setpoint of the secondary controller to be
85°C, then SUB.SP should be set to 47.2 (47.2% of 180 is about 85).
Unit of measurement:
Options:
0.0...100.0
4.8.15. S.RM.EN - Enabling ramp for slaved controller
Acronym
S.RM.EN
PR.STP.1 (o PR.STP.2...PR.STP.192) SUBDUED SETPOINT RAMP ENABLE
se modalità"Programmatore semplificato"disattiva; o PR.STP.1...PR.STP.16
SUBDUED SETPOINT RAMP ENABLE se modalità"Programmatore semplifica-
to"attiva.
If the S.SP.EN function is enabled, the parameter enables and disables the setpoint ramp for the slaved controller.
Unit of measurement:
Options:
OFF
On
4.8.16. ENBL.1 - Consent 1 to execute step
Acronym
ENBL.1
PR.STP.1 (o PR.STP.2...PR.STP.192) STEP ENABLE FOR STEP START se
modalità"Programmatore semplificato"disattiva; o PR.STP.1...PR.STP.16 STEP
ENABLE FOR STEP START se modalità"Programmatore semplificato"attiva.
The parameter shows and sets consent 1 condition to enable execution of the step.
The consents automatically check that certain conditions have been met before the program continues.
There are 4 different consents (1, 2, 3 and 4) and, at the start of the step, the state of each must match the programmed
state.
Consents can be set via digital inputs, function block outputs, and the RS485 serial input.
If even one of the consents does not match the programmed state, the step is not executed.
If all consents are set to nonE, execution of the step is not conditioned and is always executed.
Unit of measurement:
Options:
nonE
On
OFF
4.8.17. ENBL.2 - Consent 2 to execute step
Acronym
ENBL.2
PR.STP.1 (o PR.STP.2...PR.STP.192) STEP ENABLE FOR STEP START se
modalità"Programmatore semplificato"disattiva; o PR.STP.1...PR.STP.16 STEP
ENABLE FOR STEP START se modalità"Programmatore semplificato"attiva.
The parameter shows and sets consent 2 condition to enable execution of the step.
See ENBL.1 for details.
Scrolling message
%
Scrolling message
-
= Disables setpoint ramp for slaved controller
= Enables setpoint ramp for slaved controller
Scrolling message
-
= Consent state is ignored, i.e., step is always executed
= Consent must be on to execute step
= Consent does not have to be on to execute step
Scrolling message
80209C_MHW_850-1650-1850_02-2020_ENG_pag. 79
Submenu
Attributes
PR.STP
R W
Submenu
Attributes
PR.STP
R W
Submenu
Attributes
PR.STP
R W
Submenu
Attributes
PR.STP
R W
Advertisement
Table of Contents
