YASKAWA FSDrive-MV1000 Parameter Manual page 59

H2-
Function
Setting
Inrush Current Suppression
62
Circuit Fault
Function 0 to 60 with Inverse
100 to 160
Output
No.
Name
(Addr.)
Analog Input 1
H3-01
Signal Level
(410H)
Selection
H3-02 Analog Input 1
(434H) Function Selection
H3-03
(411H)
Analog Input 1 Gain Sets the level of the input value selected in H3-02 when 10 V is input at
H3-04
(412H)
Analog Input 1 Bias Sets the level of the input value selected in H3-02 when 0 V is input at
Analog Input 2
H3-09
Signal Level
(417H)
Selection
H3-10 Analog Input 2
(418H) Function Selection
H3-11
(419H)
Analog Input 2 Gain Sets the reference value for the function assigned for analog input 2 in %
H3-12
(41AH)
Analog Input 2 Bias Sets the amount of bias for the function assigned for analog input 2 in %
H3-13 Analog Input Filter
(41BH) Time Constant
Analog Input
H3-14
Terminal Enable
(41CH)
Selection
H3-16 Analog input 1
(2F0H) Offset
H3-17 Analog input 2
(2F1H) Offset
YASKAWA ELECTRIC TOEP C710687 03B FSDrive-MV1000 Parameter Guide
H2 Contact Output Settings
All Modes
Open: The inrush current suppression circuit fault has been detected.
Note: This setting is available from the drive software versions S0109 and later.
All Modes
Inverts the output switching of the contact output functions.
Set the last two digits of 1
Example: 108: Reverses the output of 8 (During Baseblock)
14C: Reverses the output of 4C (During Fast Stop)
H3: Analog Inputs
All Modes
0: 0 to 10 V
1: -10 to 10 V
All Modes
Sets the function of analog input 1.
All Modes
analog input 1.
All Modes
analog input 1.
All Modes
0: 0 to 10 V
1: -10 to 10 V
All Modes
Sets the function of analog input 2.
All Modes
units when 10 V is input.
All Modes
units when 0 V is input.
All Modes
Sets a primary delay filter time constant for analog inputs 1 and 2. Used for
noise filtering.
All Modes
Determines which analog input terminals will be enabled when the analog
input is set for "PID target value" (H3-
1: Analog input 1 only
2: Analog input 2 only
3: Analog inputs 1 and 2 only
All Modes
Adds an offset when the analog signal to analog input 1 is at 0 V.
All Modes
Adds an offset when the analog signal to analog input 2 is at 0 V.
Description
to reverse the output signal of that specific function.
Description
= C).
1.3 Parameter Table
common_
common_
Setting
common_ Default: 0
Min: 0
Max: 1
Default: 0
common_
Min: 0
Max: FF
common_ Default: 100.0%
Min: -999.9%
Max: 999.9%
Default: 0.0%
common_
Min: -999.9%
Max: 999.9%
Default: 1
common_
Min: 0
Max: 1
Default: 0
common_
Min: 0
Max: 32
Default: 100.0%
common_
Min: -999.9%
Max: 999.9%
common_ Default: 0.0%
Min: -999.9%
Max: 999.9%
common_ Default: 0.03 s
Min: 0.00 s
Max: 2.00 s
common_
Default: 3
Min: 1
Max: 3
Default: 0
common_
Min: -500
Max: 500
Default: 0
common_
Min: -500
Max: 500
Page
191
191
Page
192
193
193
193
194
194
194
194
194
194
195
195
59