YASKAWA FSDrive-MV1000 Parameter Manual page 171

2.7 H: Terminal Functions
H parameters are used to assign functions to the external terminals.
u H1: Contact Inputs
H1-02 to H1-16: Functions for Contact Inputs 2 to 16
n
These parameters assign functions to the contact inputs. The various functions and settings are listed below in
No.
H1-02 Contact Input 2 Function Selection
H1-03 Contact Input 3 Function Selection
H1-04 Contact Input 4 Function Selection
H1-05 Contact Input 5 Function Selection
H1-06 Contact Input 6 Function Selection
H1-07 Contact Input 7 Function Selection
H1-08 Contact Input 8 Function Selection
H1-09 Contact Input 9 Function Selection
H1-10 Contact Input 10 Function Selection
H1-11 Contact Input 11 Function Selection
H1-12 Contact Input 12 Function Selection
H1-13 Contact Input 13 Function Selection
H1-14 Contact Input 14 Function Selection
H1-15 Contact Input 15 Function Selection
H1-16 Contact Input 16 Function Selection
<1> The default setting is set to 73 and cannot be changed under the following conditions.
The drive software version is S0108 and later.
o2-09 is set to 2.
Setting
1 LOCAL/REMOTE Selection
2 External Reference 1/2 Selection
3 Multi-Step Speed Reference 1
4 Multi-Step Speed Reference 2
5 Multi-Step Speed Reference 3
6 Jog Reference Selection
7 Accel/Decel Time Selection 1
8 Baseblock Command (N.O.)
9 Baseblock Command (N.C.)
A Accel/Decel Ramp Hold
B Drive Overheat Alarm (oH2)
C Analog Terminal Input Selection
E ASR Integral Reset
F Through Mode
10 Up Command
11 Down Command
12 Forward Jog
13 Reverse Jog
14 Fault Reset
15 Fast Stop (N.O.)
16 Motor 2 Selection
17 Fast Stop (N.C.)
18 Timer Function Input
19 PID Disable
YASKAWA ELECTRIC TOEP C710687 03B FSDrive-MV1000 Parameter Guide
Table 2.20 Contact Input Parameters
Name Setting Range
Table 2.21 Contact Input Terminal Settings
Function
1 to 9F 40: Forward Run Command (2-Wire Sequence)
0 to 9F 6A: Drive Enable
0 to 9F 70: Drive Enable 2
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
0 to 9F F: Through Mode
Page Setting
172 31 PID Integral Hold
172 32 Multi-Step Speed Reference 4
172 33 Thermostatic Switch (N.C.)
172 34 PID Soft Starter Cancel
172 35 PID Input Level Selection
172 40 Forward Run Command (2-Wire Sequence)
172 41 Reverse Run Command (2-Wire Sequence)
172 42 Run Command (2-Wire Sequence 2)
172 43 FWD/REV Command 2 (2-Wire Sequence 2)
173 44 Add Offset Frequency 1
173 45 Add Offset Frequency 2
173 46 Add Offset Frequency 3
173 60 DC Injection Braking Command
173 61 External Search Command 1
173 62 External Search Command 2
173 63 Field Weakening
175 67 Communications Test Mode
175 6A Drive Enable
175 70 Drive Enable 2
175 71 Speed/Torque Control Switch
176 73 Door Switch NC
175 75 Up 2 Command
176 76 Down 2 Command
176 77 ASR Gain Switch
2.7 H: Terminal Functions
Default
<1>
Function
Table 2.21.
Page
178
178
178
178
178
178
178
178
178
178
178
178
178
179
179
179
179
179
179
179
179
179
179
180
171