Table of Contents
Advertisement
Asterion DC Series Programming
Command
SOURce:CURRent:MONitor:FSC <NRf>
SOURce:CURRent:MONitor:FSC?
SOURce:VOLTage <NRf>
SOURce:VOLTage?
SOURce:VOLTage[:LEVel] <NRf>
SOURce:VOLTage
[:LEVel]?
SOURce:VOLTage[:LEVel]
SOURce:VOLTage[:LEVel]
SOURce:VOLTage[:LEVel]
[:AMPLitude] <NRf>
SOURce:VOLTage[:LEVel]
[:AMPLitude?]
SOURce:VOLTage:LIMit <NRf>
SOURce:VOLTage:LIMit?
SOURce:VOLTage:LIMit[:AMPLitude] <NRf>
SOURce:VOLTage:LIMit[:AMPLitude]?
SOURce:VOLTage:PROTection <NRf>
SOURce:VOLTage:PROTection?
SOURce:VOLTage:PROTection[:LEVel] <NRf>
SOURce:VOLTage:PROTection[:LEVel]?
SOURce:VOLTage:PROTection:TRIPped?
SOURce:VOLTage:PROTection:STATe?
SOURce:VOLTage:PROTection:CLEar
SOURce:VOLTage:PROTection:PROGram<string>
SOURce:VOLTage:PROTection:PROGram?
SOURce:VOLTage:PROTection:PROGram:FSC <NRf>
M330461-01 Rev A
[:IMMediate] <NRf>
[:IMMediate]?
[:IMMediate]
[:IMMediate]
External User Control Signal Connector
Description
Sets Full Scale voltage on Current monitor pin
(IMON), when power supply is producing full
scale output current.
Returns the full scale voltage set for Current
monitor pin (IMON)
Sets the output voltage of the supply in volts
(default) or in millivolts.
Returns the output voltage of the supply in volts
or in millivolts.
Sets the output voltage of the supply in volts
(default) or in millivolts.
Returns the output voltage of the supply in volts
or in millivolts.
Sets the output voltage of the supply in volts
(default) or in millivolts.
Returns the output voltage of the supply in volts
or in millivolts.
Sets the output voltage of the supply in amps
(default) or in milliamps.
Returns the output voltage of the supply in amps
or in milliamps.
Sets the upper soft limit on the programmed
output voltage. The soft limit prevents the supply
from being inadvertently programmed above the
soft limit, thus providing a method for protecting
the load against damaging voltages.
Returns the upper soft limit set on the
programmed output voltage.
Sets the upper soft limit on the programmed
output voltage.
Returns the upper soft limit on the programmed
output voltage.
Sets the overvoltage protection trip point in volts
(default) or in millivolts.
Returns the set overvoltage protection trip point
in volts (default) or in millivolts.
Sets the overvoltage protection trip point in volts
(default) or in millivolts.
Returns the set overvoltage protection trip point
in volts or in millivolts.
Returns 1 (TRIPPED) or 0 (UNTRIPPED) state of
the overvoltage protection circuit.
Returns the state 1 (ON) or 0 (OFF) If the
overvoltage protection is enabled.
Clears the overvoltage protection circuit.
Changes the Over Voltage Programming mode
of the supply. Valid arguments are INT/0
(Internal Digital Over voltage programming)
EXT/1
(External
analog
programming)
Returns
the
setting
Programming mode
Sets the Full-Scale voltage, at which Full Scale
Over Voltage trip point will be programmed in
SCPI
Over
voltage
of
Over
voltage
9-17
N
N
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
N
N
N
- Quick Links:
- Ethernet Interface
Hide quick links:
Advertisement
Table of Contents
