Related Manuals for Ametek AMREL SPS Series
Summary of Contents for Ametek AMREL SPS Series
- Page 1 SPS Series Medium Power DC Power Supplies Operation Manual M470008-01 Rev A www.programmablepower.com...
- Page 5 About AMETEK AMETEK Programmable Power, Inc., a Division of AMETEK, Inc., is a global leader in the design and manufacture of precision, programmable power supplies for R&D, test and measurement, process control, power bus simulation and power conditioning applications across diverse industrial segments.
- Page 6 This page intentionally left blank.
-
Page 7: Safety Symbols
Neither AMETEK Programmable Power Inc., San Diego, California, USA, nor any of the subsidiary sales organizations can accept any responsibility for personnel, material or inconsequential injury, loss or damage that results from improper use of the equipment and accessories. - Page 8 This page intentionally left blank.
-
Page 9: Warranty Terms
AMETEK will, at its expense, deliver the repaired or replaced Product or parts to the Buyer. Any warranty of AMETEK will not apply if the Buyer is in default under the Purchase Order Agreement or where the Product or any part thereof: •... - Page 10 This page intentionally left blank.
-
Page 11: Remote Operation
Table of Contents FEATURES AND SPECIFICATIONS INSTALLATION III: LOCAL OPERATION REMOTE OPERATION CALIBRATION P a g e... -
Page 12: Features And Specifications
I. FEATURES AND SPECIFICATIONS INTRODUCTION The AMREL Medium Power SPS Series Switching Power Supply provides a complete solution offering to your power supply needs. The Medium Power SPS series is rated for 5kW, 10kW, and 15kW in a 3U package and 20kW, 25kW, and 30kW in a 6U package, with a wide selection of models. -
Page 13: Environmental Characteristics
The following subsections provide environmental, electrical, and physical characteristics for the SPS MEDIUM POWER Series power supplies. ENVIRONMENTAL CHARACTERISTICS PARAMETER SPECIFICATION 0.02%/°C of maximum output voltage rating for voltage set point. 0.03%/°C of TEMPERATURE COEFFICIENT maximum output current rating for current set point. AMBIENT TEMPERATURES Operating 0 to 50°C... - Page 14 FRONT PANEL AND REMOTE DIGITAL PROGRAMMING Voltage ±0.1% of full-scale output ±0.4% of full-scale output Current Overvoltage Protection (OVP) ±1% of full-scale output REMOTE DIGITAL READBACK Voltage ±0.15% of full-scale output ±0.4% of full-scale output Current REMOTE ANALOG PROGRAMMING Constant Voltage ±0.25% of full-scale output for 0-5V range (±0.5% 0-10V range) Constant Current ±0.8% of full-scale output...
- Page 15 MODELS 1&2 Amperage PARD P–P Voltage 5 kW 10 kW 15 kW 20 kW 25 kW 30 kW 0-40V 0-125A 0-250A 0-375A 0-500A 0-625A 0-750 20 mV 75 mV 0-60V 0-83A 0-167A 0-250A 0-333A 0-417A 0-500A 20 mV 75 mV 0-80V 0-63A 0-125A...
-
Page 16: Front & Rear Panel Description
FRONT & REAR PANEL DESCRIPTION: (3.) Keypad (4.) Encoder (1.) AC Power (2.) VFD Display FIGURE 1.1 3U & 6U FRONT PANEL DESCRIPTION (5.) J1 Analog Programming (6.) & (7.) Master/Slave Input & Port (25P D-SUB) Output Connector (9P D-SUB) (12.) USB (8.) GPIB (9.) Remote (13.) Positive (+) - Page 17 (1.) J1 Analog Programming (2.) Remote (3.) & (4.) Master/Slave Input & (8.) USB (6.) RS-232 (7.) LAN (5.) GPIB Port (25P D-SUB) Sense Output Connector (9P D-SUB) (9.) AC Input (10.) DC Output FIGURE 1.3 6U REAR PANEL DESCRIPTION P a g e...
- Page 18 KEYPAD DESCRIPTION 8 [ CURR or ▲ ] 7 [ VOLT ] 9 [ OV/TIME ] LOCAL [ UTILITY ] 4 [ VLIST or ◄ ] 5 [ ILIST ] 6 [ OC or ► ] MODE [ LOCKOUT ] 2 [ OVP ON/OFF or ▼...
- Page 19 P a g e...
- Page 20 DIAGNOSTIC FUNCTIONS: LCD DISPLAY MSG DESCRIPTION FAILURE MODE Fault General fault for Over Temperature/Module Fault Over Current Trip Supply has exceeded the over current protection level. Over Voltage Trip Supply has exceeded the over voltage protection level. (Allow 7s to clear OVT) External Shut Down Output disabled by J1 (analog control port) in Local Mode Digital Remote Operation (PC)