HindlePower ATevo Series Operating/Service Instructions Manual page 16

Table of Contents - ATevo
12.5 Software Configuration for Binary Inputs . . . . . . . . . . . . . . 110
12.5.1 Binary Input Configuration � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 110
12.5.2 Binary Input Name Assignment � � � � � � � � � � � � � � � � � � � � � � � � � � 111
12.5.3 Binary Active State Assignment � � � � � � � � � � � � � � � � � � � � � � � � � � 111
12.5.4 Binary Input Alarm Enable � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 112
12.5.5 Binary Input Action Assignment � � � � � � � � � � � � � � � � � � � � � � � � � 112
12.5.6 Factory Default Binary Input Configuration � � � � � � � � � � � � � � � � � 113
12.6 Software Configuration for Analog Inputs . . . . . . . . . . . . . 113
12.6.1 Analog Input Configuration � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 114
12.6.2 Analog Input Name Assignment � � � � � � � � � � � � � � � � � � � � � � � � � 114
12.6.3 Analog Input Primary Unit Assignment � � � � � � � � � � � � � � � � � � � � 115
12.6.4 Analog Input Scaling Assignment � � � � � � � � � � � � � � � � � � � � � � � � 115
12.6.5 Analog Input Alarm and Trigger Assignment � � � � � � � � � � � � � � � � 116
12.6.6 Analog Input Alarm Threshold Assignment � � � � � � � � � � � � � � � � � � 117
12.6.7 Analog Input Action Assignment � � � � � � � � � � � � � � � � � � � � � � � � � 119
12.6.8 Factory Default Analog Input Configuration � � � � � � � � � � � � � � � � � 119
13. FORCED LOAD SHARING � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 120
13.1 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
13.2 System Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
13.3 Forced Load Sharing Configuration . . . . . . . . . . . . . . . . . . . 120
13.3.1 Installing Serial Communications Adapter (A13) � � � � � � � � � � � 121
13.3.2 Configuring Serial Communications Hardware � � � � � � � � � � � � 121
13.4 Wiring ATevo Chargers for Forced Load Sharing . . . . . . . . 122
13.4.1 Configuring ATevo for Forced Load Sharing � � � � � � � � � � � � � � � 123
13.5 Forced Load Sharing Operation . . . . . . . . . . . . . . . . . . . . . . 125
13.5.1 Requirements to Maintain Forced Load Sharing � � � � � � � � � � � � 126
13.5.2 Virtual Independent Mode � � � � � � � � � � � � � � � � � � � � � � � � � � � � 126
13.5.3 Forced Load Sharing Alarms � � � � � � � � � � � � � � � � � � � � � � � � � � 127
13.6 Temperature Compensation with Forced Load Sharing . . 127
13.7 Battery Open Alarm for Forced Load Sharing . . . . . . . . . . 127
13.8 Timed Equalize with Forced Load Sharing . . . . . . . . . . . . . 127
13.9 Auto-Equalize with Forced Load Sharing . . . . . . . . . . . . . . . 128
13.10 Firmware Updates with Forced Load Sharing . . . . . . . . . . 128
13.11 Troubleshooting Forced Load Sharing ATevos . . . . . . . . . . 128
14. MAINTENANCE � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 129
14.1 Performing Routine Maintenance . . . . . . . . . . . . . . . . . . . . 129
14.1.1 Keeping ATevo Clean � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 129
14.1.2 Checking Power and Signal Connections � � � � � � � � � � � � � � � � � � � 129
14.1.3 Checking Remote Sense Wiring - optional � � � � � � � � � � � � � � � � � � � 129
14.1.4 Checking Temperature Compensation Probe - optional � � � � � � � � � 130
14.1.5 Measuring Output Ripple Voltage � � � � � � � � � � � � � � � � � � � � � � � � 130
xvi
ATevo