HindlePower ATevo Series Operating/Service Instructions Manual page 12

Table of Contents - ATevo
4.2 Configuring Basic Set Points and Alarms . . . . . . . . . . . . . . . . 37
4.2.1. How to Configure General Parameter Settings � � � � � � � � � � � � � � � � � 37
4.2.2 Setting Float Voltage � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 38
4.2.3 Setting Equalize Voltage � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 38
4.2.4 Setting Equalize Timer � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39
4.2.5 Setting High DC Alarm Voltage � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39
4.2.6 Setting Low DC Alarm Voltage � � � � � � � � � � � � � � � � � � � � � � � � � � � � 39
4.2.7 Setting Current Limit Level � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 40
4.3 Configuring Advanced Set Points and Alarms . . . . . . . . . . . . 41
4.3.1 How to Configure Advanced Settings � � � � � � � � � � � � � � � � � � � � � � � � 41
4.3.2 Setting High Voltage Shutdown � � � � � � � � � � � � � � � � � � � � � � � � � � � � 41
4.3.3 Setting High Level Detect � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 42
4.3.4 Setting End of Discharge (EOD) Alarm � � � � � � � � � � � � � � � � � � � � � � � 42
4.3.5 Setting Low Voltage Level Detect � � � � � � � � � � � � � � � � � � � � � � � � � � � 42
4.3.6 Setting AC Ripple Alarm � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 43
4.3.7 Setting Positive (+) Ground Fault Sensitivity Level � � � � � � � � � � � � � � � 43
4.3.8 Setting Negative (-) Ground Fault Sensitivity Level � � � � � � � � � � � � � � 43
4.3.9 Setting Battery Temperature Compensation � � � � � � � � � � � � � � � � � � � 44
4.3.10 Setting Battery Type for Temperature Compensation � � � � � � � � � � � � 44
4.4 Configuring System Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
4.4.1 How to Configure System Settings � � � � � � � � � � � � � � � � � � � � � � � � � � 45
4.4.2 Setting System Time � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 45
4.4.3 Setting System Date � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 46
4.4.4 Setting Display Backlight Control � � � � � � � � � � � � � � � � � � � � � � � � � � 46
4.4.5 Setting Display Contrast � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 46
4.4.6 Setting Display Backlight Intensity � � � � � � � � � � � � � � � � � � � � � � � � � � 47
4.4.7 Setting Display Reverse Image Control � � � � � � � � � � � � � � � � � � � � � � 47
4.5 Configuring Relays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
4.5.1 Configuring Common Alarm Relay � � � � � � � � � � � � � � � � � � � � � � � � � 47
4.5.2 Configuring Auxiliary I/O Board Relays � � � � � � � � � � � � � � � � � � � � � � 49
4.6 Disabling Alarms in Common Alarm List . . . . . . . . . . . . . . . . 49
4.7 Configuring Serial Communications Adapter . . . . . . . . . . . . . 50
4.8 Configuring Ethernet Communications Adapter . . . . . . . . . . 50
4.9 Enabling/Disabling High Level Detect . . . . . . . . . . . . . . . . . . . 51
5. BASIC OPERATION � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 52
5.1 ATevo Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
5.1.1 Changing Display Mode � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 52
5.1.2 Changing Charge Mode � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 53
5.1.3 Changing Equalize Method � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 54
5.1.4 Lamp Test & Display of Firmware Versions � � � � � � � � � � � � � � � � � � � � 55
5.1.5 Resetting Latched Relays (legacy method) � � � � � � � � � � � � � � � � � � � � 55
xii
ATevo