Chevrolet 30 Series 1967 Service Manual page 81

1. Base Assy. , w/Bearings
2. O uter Lever Assy. , w/Pins and Bearings
3. Bearing, Flanged
4. Pin-D rive
5. C enter Lever Assy.
6. Bearing, Housing, L. H.
7.
Bearing, Housing, R. H.
8. Roller and Bearing Assy.
9. Stud
10.
Snap Ring
Washer, Plain
11.
12. Lockwasher, 3/8 SA E Med.
13. N u t, Hex. 3/8-16 (U N C - 2 B )
14. Bearing, Flanged
15. W asher, P lain 7 G a . x 17/32 x 7/8
16. Shock Lever Assy. K it
17. Shock Lever Assy.
18. Hinge Shaft, Shock
19. Hinge Shaft, Shock, Rear
20.
Roll Pin
21. Shock Absorber Assy. K it
Fig. 43 - Adjuster Lever
22. Shock Absorber Assy. , w/Bearings
23. Bearing K it (Shock Absorber)
24. Bearing, Flanged
25. Retainer (T-Bar)
26. Yoke (Adjuster)
27. Torsion Bar Set (2 Bars per Set)
28. Side Panel Assy. , L. H.
29.
Side Panel Assy. , R. H.
30. Adjuster Screw and Lever Assy.
31. G e a r
32. Adjuster Screw
33. Lever Assy.
Washer
34.
35. Spring (Tension)
36. Acorn N u t (S e lf Locking)
37. Pin , Drive
38. W asher, Plain
39. Thrust Ball Bearing
40. Adjuster Pin
W asher, Plain 5/16 Thick x 11/16 x 1-1/4 59.
41.
42. Lub. Fittings (3/32 Shank)
Refer to Fig. 41
Shock Absorber
Removal
1. Wedge upper seat in top position following operation
2. Remove preload on torsion bars following procedure
3. Remove seat cushion following operation 4, torsion
4. Wire side panel assemblies (Nos. 28 and 29) across
5. Remove (2) snap rings (No. 10) from ends of hinge
6
7. Remove (2) roll pins (No. 20) from hinge shaft at
43. Knob (Plastic)
Thrust Washer
44.
45. Roller and Bearing Assy. , (Rubber)
46. W asher, P la in , 5/16 SA E , Z in c Plated
47. Lock Washer, 5/16 SAE M ed. , Z in c Plated
48. N u t, Hex. 5/16-18 (U N C - 2 B ) Z in c Plated
49. Bumper (Topping)
50. Seat Adjuster, R. H.
51. Seat Adjuster, L. H.
52. Cap Screw , 5/16-18 x 5/8 Lg. ,
F illis te r— Ph iIIips Z in c Plated
53. Bumper (Bottom)
54. Seat Cushion Assy.
55. C over Assy. , Seat Cushion
Pad, Seat Cushion
56.
57. Back Cushion Assy.
C over Assy. , Back Cushion
Pad, Back Cushion
58. Universal Riser K it
Fastener C lip , Cushion
60. Ride Level Indicator
Fig. 44 - Shock Absorber
, torsion bar removal.
1
sim ilar to operation 2, torsion bar removal.
disengage adjuster assembly.
bar removal.
front of seat to retain their position (19-3/4" from
outer surface to outer surface).
shaft (No. 18) at front of shock absorber.
. Remove hinge shaft (No. 18) by tapping out from left
hand to right hand side. This operation frees (2)
washers (No. 15).
BODY IB - 19
Do not
CHEVROLET TRUCK SERVICE MANUAL