Chevrolet 30 Series 1967 Service Manual page 418

CLUTCHES AND TRANSMISSIONS 7-32
joint flange, and universal joint flange retainer nut on
mainshaft. Tighten retainer nut to 125 ft. lbs. and
install cotter pin.
7. Replace speedometer driven gear.
TRANSMISSION
Removal From Vehicle
1. Drain lubricant from transmission.
2. Disconnect and remove parking brake lever.
3. Disconnect and drop propeller shaft at transmission.
4. Remove the transmission gearshift lever as outlined
under "Maintenance and Adjustments."
5. Remove screws which fasten steering jacket grom-
met to floor and slide grommet up jacket out of the
way.
. Remove accelerator pedal and floor mat.
6
7. Remove the sheet metal screws attaching transmis­
sion cover to body floor and remove cover.
. Disconnect the speedometer cable from the speedom­
8
eter driven gear fitting at the transmission rear
bearing retainer.
9. Remove the two top cap screws attaching the trans­
mission to clutch housing and insert two transm is­
sion Guide Pins Tool J-1126 in these holes.
10. Remove the flywheel underpan and remove the two
lower transmission to clutch housing capscrews.
11. Slide the transmission straight back on the guide pins
until the clutch gear is free of the splines in the
clutch disc. The guide pins in the top holes support
the transmission during this operation and prevent
damage to the clutch disc.
FIVE-SPEED TRANSMISSION (SPICER 3 0 0 0 SERIES)
General Description.........................................................
Maintenance and Adjustments
Gearshift L e v e r ..........................................................
Transmission C o v e r ...................................................
The 5 -speed transmission (Spicer) is a manually
shifted, synchromesh, helical gear type.
speed is direct drive. The clutch or main drive gear
bearing is a single row ball type. The mainshaft is sup­
ported by a straight roller pilot bearing at the front and a
single row ball bearing at the rear.
mounted on a straight roller bearing at the front and a
GEARSHIFT LEVER
Removal
1. P ress down on gearshift lever spring cup and drive
locking pin out of lever.
seal (fig. IS).
2. Remove snap ring from groove in lever housing and
SERVICE OPERATIONS
Page
7-32
....................................... 7-32
7-32
7-33
GENERAL DESCRIPTION
Fifth forward
The countershaft is
MAINTENANCE AND ADJUSTMENTS
Lift off cup, spring, cap and
. Install propeller shaft and install and adjust propel­
8
ler shaft brake.
9. If the transmission was drained, refill with S.A.E. 90
gear lubricant.
12. Remove the transmission from vehicle.
Installation in Vehicle
1. Install guide pins, J-1126, in clutch housing. Posi­
tion transmission under vehicle and raise into posi­
tion on guide pins.
2. Start clutch gear shaft in clutch disc and slide
forward.
3. Install the transmission mounting bolts. Torque bolts
to 70-75 ft. lbs.
4. Install the flywheel underpan.
5. Reconnect the propeller shaft.
. Install and adjust the parking brake.
6
7. If not installed with cover assembly, install trans­
mission gearshift lever as outlined under "Mainte­
nance and Adjustments."
. Connect speedometer cable to the driven gear fitting
8
in the transmission rear bearing retainer.
9. Tighten drain plug and fill transmission with S.A. E.
90 gear lubricant. Install filler plug and tighten.
10. Install the transmission floor cover to body floor.
11. Install the floor mat and connect the foot accelerator
pedal.
12. Slide the mast jacket grommet in position and install
the retainer screws.
13. Road test the vehicle for operation of transmission in
all speeds.
INDEX
Service O perations............................................................
Removal from V e h i c l e ................................................
Installation in Vehicle
single row ball bearing at the rear.
cluster rotates on two straight roller bearings. A 9 -1 /2 "
x 3" band type propeller shaft parking brake is mounted
at the rear of the transmission, except tandems with
auxiliary transmissions. Power take-off openings are
provided on both the right and left sides of the transmis­
sion case.
tap out slotted pin. Lift lever out of housing.
Installation
1. Insert lever in housing with slot in lever in line with
hole through side of cover, and curve in lever to
rear.
2. Install slotted pin through housing and lever and in­
................................................
The reverse idler
CHEVROLET TRUCK SERVICE M ANUAL
Page
7-35
7-35
7-35