Autoreclose Ddb Signals - GE MiCOM P40 Technical Manual

P446SV
Signal Name
TARA CB1-pole / 3-pole trip (13)
TARAny CB1-pole / 3-pole trip (13)
TARB CB1-pole / 3-pole trip (13)
TARC CB1-pole / 3-pole trip (13)
TMEM1Ph CB1-pole / 3-pole trip (13)
TMEM2/3Ph CB1-pole / 3-pole trip (13)
TMEM3Ph CB1-pole / 3-pole trip (13)
TMemAny CB1-pole / 3-pole trip (13)
4.3

AUTORECLOSE DDB SIGNALS

The following table lists all the DDB signals used in the CB control and Autoreclose logic system:
DDB Signal Name DDB Signal Number
1P DTime 1554
1P Follower Time 1446
1P Reclaim TComp 1568
1P Reclaim Time 1567
1PF TComp 1561
2/3 Ph Fault 527
3 Ph Fault 528
3P Dead Time IP 853
3P DTime1 1556
3P DTime2 1557
3P DTime3 1558
3P DTime4 1559
3P Follower Time 1447
3P Reclaim TComp 1570
3P Reclaim Time 1569
3PF TComp 1562
Any Trip 522
AR CB1 No C/S 308
AR CB1 Unhealthy 307
P446SV-TM-EN-1
Source
CB Trip Time Monitor (53)
Force 3-phase Trip (10)
CB1-pole / 3-pole trip (13)
Evolving Fault (20)
CB Trip Time Monitor (53)
CB Trip Time Monitor (53)
1-phase AR Cycle Selection (19)
CB1 AR In Progress (16)
Autoreclose Lockout (55)
CB Trip Time Monitor (53)
Autoreclose Lockout (55)
CB1 AR In Progress (16)
Evolving Fault (20)
3-phase AR cycle selection (21)
Source Module (Module Number)
1-phase AR Dead Time (24)
Follower 1-phase CB AR Time (28)
Reclaim Time (35)
Reclaim Time (35)
Follower 1-phase CB AR Time (28)
CB Trip Conversion (63)
CB Trip Conversion (63)
3-phase AR Dead Time (25)
3-phase AR Dead Time (25)
3-phase AR Dead Time (25)
3-phase AR Dead Time (25)
3-phase AR Dead Time (25)
Follower 3-phase CB AR Time (29)
Reclaim Time (35)
Reclaim Time (35)
Follower 3-phase CB AR Time (29)
CB Trip Conversion (63)
CB Healthy and System Check Timers (39)
CB Healthy and System Check Timers (39)
Destination
An A-phase trip has initiated Autoreclose
Any trip has initiated Autoreclose
A B-phase trip has initiated Autoreclose
A C-phase trip has initiated Autoreclose
Signal to remember that Autoreclose was
initiated by a single-phase fault
Signal to remember that Autoreclose was
initiated by a 2-phase fault or a 3-phase
fault
Signal to remember that Autoreclose was
initiated by a 3-phase fault
Signal to remember that Autoreclose was
initiated by an AnyTrip
Sequence Counter (18)
Evolving Fault (20)
Successful AR Signals (36)
Reclaim Time (35)
Follower 1-phase CB AR Time (28)
Successful AR Signals (36)
Reclaim Time (35)
Follower 1-phase CB AR Time (29)
AR Initiation (11)
CB1 Autoclose (32)
CB2 Autoclose (33)
CB Control (43)
CB2 Control (44)
Autoreclose Lockout (55)
Force 3-phase Trip (10)
Autoreclose Lockout (55)
Leader Follower Logic (7)
Chapter 11 - Autoreclose
Description
Destination Module (Module Number.)
277