GE MiCOM P40 Technical Manual page 836

Appendix B -Settings and Signals
MENU TEXT
Setting that defines the operative mode of the received InterMiCOM_6 signal.
When 'Direct' tripping is chosen, for security reasons 2 consecutive valid messages have to be received before a change in the signal status
will be acknowledged. That will impose an additional 1-2 ms delay comparing to 'Permissive' mode.
Set 'Direct' in Direct Transfer Tripping (Intertripping) applications.
Set 'Permissive' to accommodate any Permissive or Blocking scheme.
IM6 FallBackMode
Setting that defines the status of IM6 signal in case of heavy noise and message synchronization being lost.
If set to Latching the last valid IM6 status will be maintained until the new valid message is received.
If set to Default, the IM6 status, pre-defined by the user in IM6 Default Value cell will be set. A new valid message will replace IM6 Default
Value, once the channel recovers.
IM6 DefaultValue
Setting that defines the IM6 fallback status.
IM7 Cmd Type
Setting that defines the operative mode of the received InterMiCOM_7 signal.
When 'Direct' tripping is chosen, for security reasons 2 consecutive valid messages have to be received before a change in the signal status
will be acknowledged. That will impose an additional 1-2 ms delay comparing to 'Permissive' mode.
Set 'Direct' in Direct Transfer Tripping (Intertripping) applications.
Set 'Permissive' to accommodate any Permissive or Blocking scheme.
IM7 FallBackMode
Setting that defines the status of IM7 signal in case of heavy noise and message synchronization being lost.
If set to Latching the last valid IM7 status will be maintained until the new valid message is received.
If set to Default, the IM7 status, pre-defined by the user in IM7 Default Value cell will be set. A new valid message will replace IM7 Default
Value, once the channel recovers.
IM7 DefaultValue
Setting that defines the IM7 fallback status.
IM8 Cmd Type
Setting that defines the operative mode of the received InterMiCOM_8 signal.
When 'Direct' tripping is chosen, for security reasons 2 consecutive valid messages have to be received before a change in the signal status
will be acknowledged. That will impose an additional 1-2 ms delay comparing to 'Permissive' mode.
Set 'Direct' in Direct Transfer Tripping (Intertripping) applications.
Set 'Permissive' to accommodate any Permissive or Blocking scheme.
IM8 FallBackMode
Setting that defines the status of IM8 signal in case of heavy noise and message synchronization being lost.
If set to Latching the last valid IM8 status will be maintained until the new valid message is received.
If set to Default, the IM8 status, pre-defined by the user in IM8 Default Value cell will be set. A new valid message will replace IM8 Default
Value, once the channel recovers.
IM8 DefaultValue
Setting that defines the IM8 fallback status.
SECURITY CONFIG
User Banner
Attempts Limit
Attempts Timer
B90
COL ROW DEFAULT SETTING
20 45 Default
20 46 0
20 48 Permissive
20 49 Default
20 4A 0
20 4C Permissive
20 4D Default
20 4E 0
25 00
ACCESS ONLY FOR
25 01
AUTHORISED USERS
25 02 2
25 03 2
DESCRIPTION
Default
Latched
[Indexed String]
0 or 1
[Unsigned Integer(16 bit)]
Direct
Permissive
[Indexed String]
Default
Latched
[Indexed String]
0 or 1
[Unsigned Integer(16 bit)]
Direct
Permissive
[Indexed String]
Default
Latched
[Indexed String]
0 or 1
[Unsigned Integer(16 bit)]
From 32 to 234 in steps of 1
[ASCII Text]
From 0 to 2 in steps of 1
[Unsigned Integer (16 bits)]
From 1 to 3 in steps of 1
[Unsigned Integer (16 bits)]
AVAILABLE OPTIONS
P446SV-TM-EN-1
P446SV