Prog.mix - Programmable Mixer - GRAUPNER mz-24 Pro Programming Manual

Programmable Mixers
Programmable Linear and Curve Mixers
In addition to the different model types, per each
set-up phase there are five linear mixers and three
7-point curve mixers in each of the 30 model mem-
ories.
To change these settings, from the main display press
the FUNCTION menu gear icon (blue "F") to bring up
the FUNCTION submenu screen:
000%
000:00.0
000 000
mz
000:00.0
0:01:23
Press
M - 1
000 000
PHASE 1
MODELLNAME 1
BATT TIME 00: 01: 23
000
From the FUNCTION submenu display, press the
Prog.MIX icon:
BACK BASE FUNCTION
Phase D/R,EXP THR.CRV Prog.MIX
Press
Logical sw Sequence
Phase-Dependent Settings of Programmable
Mixers
This submenu allows for different phase-specific val-
ues to be programmed. Phase names are displayed
in green in the upper left side of the screen next to
the BACK button. Standard default naming for the
phases are usually displayed as NORMAL/PHASE
1. (Additional phases will be named numerically, e.g.
Phase 2, Phase 3, etc.) To define multiple phases,
refer to the FUNCTION submenu Phase section (page
120). Each new phase will need to be assigned to a
different switch. To change the phases, activate the
corresponding switch(es).
134 Function menu | general - Free mixer
Page Change
Linear mixers (1 to 5) are shown on the first display
page. Press the
er display (6 to 8):
1.
000%
2.
4.2V
3.
4.
5.
000
SYSTEM
Trainer Mixer Setup
Change to the appropriate phase.
Choose a number line to assign the mixer and press
the NONE
is being assigned to Line 1:
1.
2.
3.
4.
5.
NEXT
button to view the curve mix-
BACK PHASE 1 Prog.MIX SERVO
ACT MST SLV SET LIN.MIX
INH NONE NONE NEXT
>>
INH NONE NONE
>>
Press
INH NONE NONE
>>
INH NONE NONE
>>
INH NONE NONE
>>
BACK PHASE 1 Prog.MIX SERVO
ACT MST SLV SET CRV.MIX
INH NONE NONE NEXT
6. >>
INH NONE NONE
>>
7.
INH NONE
NONE >>
8.
button. In the example below, the mixer
BACK PHASE 1 Prog.MIX SERVO
ACT MST SLV SET LIN.MIX
INH NONE NONE NEXT
>>
INH NONE NONE
>>
Press
INH NONE NONE
>>
INH NONE NONE
>>
INH NONE NONE
>>
The Master >> Slave (source >> target) selection dis-
play page for the mixer appears:
BACK PHASE 1 Prog.MIX
NONE NONE
>>
CH1 CH2 CH3 CH4 CLR
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
• MST
To choose the source (master) channel for mixer
NONE
input, press the first (left)
BACK PHASE 1 Prog.MIX
NONE NONE
>>
Press
CH1 CH2 CH3 CH4 CLR
CH5 CH6 CH7 CH8
CH9 CH10 CH11 CH12
The button highlights blue:
BACK PHASE 1 Prog.MIX
NONE NONE
>>
CH1 CH2 CH3 CH4 CLR
CH5 CH7 CH8
CH6
CH9 CH10 CH11 CH12
Press to select control function 1 to 12. In the ex-
ample below, CH1 needs to be assigned:
SERVO
button:
SERVO
SERVO