Programming Examples; Phase Specific Flaps Trimming - GRAUPNER mz-24 Pro Programming Manual

Programming Example
Phase-Specific Flaps Trimming
The following example shows how to correct the
trimming of the phase-specific (and recallable) flaps
trimming through only one control element in all the
phases.
To understand this programming example make sure:
individual menu descriptions are read and under-
stood, be familiar with basic transmitter use, perform
the fixed-wing Receiver Configuration according to
the instructions (page 32), completely program the
model into the transmitter, mechanically adjust the
controls and understand the correct lateral deflec-
tion of all rudders. It helps, but does not hinder, if the
model has already performed test flights and received
the resulting adjustments.
Programming
Turn on the transmitter and start programming the
flaps positions in the BASE submenu Trim Step.
Trim Step
BACK PHASE 1
Trim Step
CO T1 T2 T3 T4
STEP 04 04 04 04
POS 000% 000% 000% 000%
000%
SET 000% 000% 000%
D.TRIM 1 NONE AUTO TRIM INH
D.TRIM 2 NONE CTL ON
In one of the two D.TRIM lines press to highlight blue
the NONE | button. Press the INC
or the arrow keys ( pq ) to select CH6:
BACK
PHASE 1 Trim Step
CO T1 T2 T3 T4
STEP 04 04 04 04
POS 000% 000% 000% 000%
SET 000% 000% 000% 000%
D.TRIM 1 CH 6 AUTO TRIM INH
D.TRIM 2 NONE CTL ON
230 Programming example - Flaps trimming
Back out and navigate to the FUNCTION submenu
Prog.MIX.
Prog.MIX
Bring up the desired phase.
Program the mixer numbers into the phase according
to the following schema:
• Left/Right Ailerons:
CH6 >> CH2
CH6 >> CH5
• Single Left/Right Flaps Pair:
CH6 >> CH6
CH6 >> CH7
• Second Left/Right Flaps Pair:
CH6 >> CH9
CH6 >> CH10
For a model type with 2AILE 2FLAPS, reference the
"THERMAL" display example as follows:
SERVO
VIEW
1.
INC
2.
RES
3.
DEC
4.
SET
5.
The mixing direction of the individual mixer pairs may
need to be set individually, depending on the wing
or DEC buttons
servos installation situation and the desired operating
direction of the selected digital trim button.
SERVO
VIEW
INC
RES
DEC
SET
BACK SERVO
THERMAL Prog.MIX
ACT MST SLV SET
>>
ON CH 6 CH 2 NEXT
>>
ON CH 6 CH 5 >>
>>
>>
ON CH 6 CH 6
>>
>>
ON CH 6 CH 7
>>
ON CH 6 CH 3 >>
>>
Individually setting mixing directions allows for con-
trasting and parallel mixing directions for each flap
pair:
BACK THERMAL
Prog.MIX
>>
CH6 CH2 TRIM ON
ACT ON CTL ON
A +050% B +050%
OFFSET X 000%
OFFSET Y 000%
SYM OFF
BACK
THERMAL Prog.MIX
CH6 >> CH5 TRIM ON
ACT ON CTL ON
A –050% B –050%
OFFSET X 000%
OFFSET Y 000%
SYM OFF
In both cases, the trimming distance (max. 37.5% at
125% admixture) is determined according to the mix-
ing proportion:
BACK THERMAL Prog.MIX
>> CH2 TRIM ON
CH6
ACT ON CTL ON
A +050% B +050%
OFFSET X 000%
OFFSET Y 000%
SYM OFF
BACK
THERMAL Prog.MIX
>>
CH6 CH5 TRIM ON
ACT ON CTL ON
A –050% B –050%
OFFSET X 000%
OFFSET Y 000%
SYM
OFF
SERVO
INC
RES
DEC
SERVO
INC
RES
DEC
SERVO
INC
RES
DEC
SERVO
INC
RES
DEC