GRAUPNER mz-24 Pro Programming Manual page 214

The fields are now empty; the password previously
saved has been deleted.
BACK CLR
A B C D E
Current Unlock Code
G H I
M N O P Q R
New Unlock Code
S T U V W X
_
Y Z << <
Trim lock
CAPS NUM
OFF
Press the BACK button to save and exit.
Battery Type Line
To enter or change the type of power supply battery,
update the setting in the Battery type line. The trans-
mitter can run on either a four-cell nickel–metal hy-
dride battery (NIMH) or a 1s lithium-ion battery (LIPO).
To make any necessary changes to the setting, press
the value field in the Battery type line:
BACK Etc. Set
>>
Touch unlock
Battery type
LIPO
Batt warning 3.6V
Press
Power on Melody ON
Voice Volume 03 NULL
Vario Volume 03
The field highlights blue:
BACK Etc. Set
Touch unlock >>
Battery type LIPO
Batt warning 3.6V
Power on Melody ON
Voice Volume 03 NULL
Vario Volume 03
Press the INC or DEC buttons or the arrow keys
( pq ) to select the appropriate value:
214 System menu - ETC set
Touch unlock
Battery type
F
Batt warning
J K L
Power on Melody
Voice Volume
Vario Volume
=
Press the RES
SPECIAL
back to the default.
Batt Warning Line
Use this setting to program the warning threshold of
the display depending on the battery type selected
in the line above. Nickel–metal hydride batteries can
be set, in increments of 0.1V, between 4.5 and 5.5V.
Lithium-ion/lithium polymer batteries can be set, in in-
crements of 0.1V, between 3.4 and 4.2 V. Do not set
value too low or there will not be sufficient time to land
the model after a battery warning.
To make any necessary changes to the setting, press
the value field of the Batt warning line:
INC
Touch unlock
RES
Battery type
DEC
Batt warning
Power on Melody
Voice Volume
Vario Volume
The field highlights blue:
INC
Touch unlock
RES
Battery type
DEC
Batt warning
Power on Melody
Voice Volume
Vario Volume
Etc. Set
BACK
>>
NIMH
INC
4.8V
ON RES
DEC
03 NULL
03
button to reset the changed value
Etc. Set
BACK
>>
NIMH
INC
4.8V
ON RES
Press
03 NULL DEC
03
BACK Etc. Set
>>
NIMH
4.8V INC
ON RES
03 NULL DEC
03
Press the INC or DEC buttons or the arrow keys
( pq ) to select the appropriate value:
Etc. Set
BACK
Touch unlock >>
Battery type NIMH
Batt warning 4.6V
Power on Melody ON
Voice Volume 03 NULL
Vario Volume 03
Press the RES button to reset the changed value
back to the default.
Check the transmitter voltage at any time by pressing
the red mz in the center of the main display menu to
bring up the following data display:
BACK CLR AUTO LOAD
TX VOLT 00 RX VOLT
3.6V
STRENGTH 00 STRENGTH ALARM
000%
ON
ESC STR 00 ESC VOLT
000.0A
Tip
In a special calibration menu that can be opened by
touching the voltage display in the main display menu:
000%
Press
000:00.0
000 000
mz
000:00.0
0:01:23
M - 1
000 000
PHASE 1
MODELLNAME 1
BATT TIME 00: 01: 23
000
The voltage display and battery warning threshold of
can be fine-tuned using a precision voltmeter. Press
to highlight blue the Cali. Data column value field and
press the +2 , +10 , -2 or -10 buttons to incremen-
INC
RES
DEC
ON
00
3.7V
00
00.0V
000%
4.2V
000