GRAUPNER mz-24 Pro Programming Manual page 108

Generally, a nonlinear control function is used for the
aileron (channel 2), elevator (channel 3) and rudder
(channel 4). These channel settings also correspond
to the default factory setting.
Note
This assignment is only applicable to tail types
other than V-wing or 2ElevSv 3+8, or flaps other
than 2AILE or 2/4AILE 2/4FLAP. Otherwise, the
control function 3 (elevator) is split to control channels
3 + 8 in the transmitter, and control functions 2 (aile-
ron) is split to control channels 2 + 5 for the left and
right aileron. In these two cases, the corresponding
control channels (INPUT CH) of the receiver would be
channels 03 + 08 and 02 + 05.
Set two curves, for example, if a model's flaps are
specified as 2AILE and pilots wish use the RX
CURVE option instead of the individually programma-
ble FUNCTION submenu D/R,EXP (page 124). Other-
wise, the left and right aileron have different control
characteristics:
BACK Telemetry
RX CURVE V6.35 < >
RECV
CURVE1 CH : 02
GAM
TYPE : B
>CURVE2 CH : 05
EAM
TYPE : B
VARIO
CURVE3 CH : 04
TYPE : B
GPS
ESC
CURVE 1, 2 or 3 CH
Select the desired control channel (INPUT CH).
The following setting in TYPE only affects the selected
control channel.
TYPE
Select the servo curve:
A EXP = -100 % and D/R = 125%
108 Base menu - Telemetry | SETTINGS/DISPLAYS
The servo reacts strongly to control stick move-
ment around the neutral position. The curve be-
comes flatter as the rudder deflection increases to
about 125% of the servo travel.
B Linear setting.
The Servo follows the control stick travel in a linear
manner in case of unchanged servo travel.
C EXP = +100 % and D/R = 70%
The servo reacts weakly to control stick movement
around the neutral position. The curve becomes
steeper as the rudder deflection reduces to about
70% of the servo travel.
Notice
The control characteristics that are programmed
here affect the all mapped receiver outputs.
5CH FUNCTION: SERVO or SENSOR
BACK
RX CURVE
>CURVE1 CH :
ESC
CURVE2 CH :
DEC
CURVE3 CH :
INC
5CH FUNCTION: SERVO
ENT
SET
With certain receivers, a certain servo connection is
designed to be switchable instead of an independent
telemetry connection. For example, with the GR-12L
receiver a telemetry sensor can also be connected to
servo connection 5 (identified as 5T):
No.S1012
Connect the servo with either the receiver update
adapter cable (No. 7168.6S) or a telemetry sensor.
Telemetry
V6.35 < > RECV ESC
02
GAM DEC
TYPE : B
03 EAM
INC
TYPE : B
VARIO ENT
04
TYPE : B
GPS SET
ESC
Servo
OR
Sensor
L
In order for the connected device to be correctly iden-
tified by the receiver, servo connection 5 MUST be
switched from SERVO to SENSOR and vice versa.
Press the INC or DEC button to move the bracket
to the 5CH FUNCTION line, and press the
ton at the bottom right of the display. The field high-
lights white:
BACK Telemetry
RX CURVE V6.35 < >
RECV
CURVE1 CH : 02
GAM
TYPE : B
CURVE2 CH : 03
EAM
TYPE : B
VARIO
CURVE3 CH : 04
TYPE : B
GPS
>5CH FUNCTION : SERVO
ESC
Use the INC or DEC button to select the alternative
setting SENSOR:
BACK
Telemetry
RECV
RX CURVE V6.35 < >
CURVE1 CH : 02
GAM
TYPE : B
CURVE2 CH : 03 EAM
TYPE : B
VARIO
CURVE3 CH : 04
TYPE : B GPS
>5CH FUNCTION : SENSOR
ESC
Press the SET button again to save the selection. To
return to the main display of the transmitter, repeat-
edly press the BACK button at the top left of the
display.
SET
but-
ESC
DEC
INC
ENT
SET
ESC
DEC
INC
ENT
SET