Flap Mix - Flap Mixer - GRAUPNER mz-24 Pro Programming Manual

Flap MIX
Flap Mixer Adjustment
This submenu option is not available for models using
the 1AILE and 2AILE settings.
Use this function to adjust the elevator, aileron and
flaps to have better control in tighter curves, adjust-
ing upward or downward torque, and aileron flap pair
movement.
To adjust these settings, from the main display press
the FUNCTION menu gear icon (blue "F") to bring up
the FUNCTION submenu screen:
000%
000:00.0
000 000
mz
000:00.0
0:01:23
Press
M - 2
000 000
PHASE 1
Extra 360
BATT TIME 00: 01: 23
000
From the FUNCTION submenu, press the Flap MIX
icon:
BACK BASE FUNCTION
Phase D/R,EXPO THR.CRV Idle LOW
Snap roll Aile diff Wing MIX Flap MIX
Press
Airbrake TTrainer Logical sw Sequence
Phase-Dependent Settings
This submenu allows for different phase-specific val-
ues to be programmed. Phase names are displayed
in green in the upper left side of the screen next to
the BACK button. Standard default naming for the
phases are usually displayed as NORMAL/PHASE
1. (Additional phases will be named numerically, e.g.
Phase 2, Phase 3, etc.) To define multiple phases,
refer to the FUNCTION submenu Phase section (page
120). Each new phase will need to be assigned to a
192 Function menu | Airplane models - Flaps mixer
different switch. To change the phases, activate the
corresponding switch(es).
000%
Programming
4.2V
• ACT Column
To activate
combination, press to change the value fields in
the appropriate row.
This turns on and off the effect of the control ele-
ment on the selected mixer when the value field
000
is ON and a switch is assigned to the specific
phase.
• SET Column
SYSTEM
To switch to the mix type setting display menu,
press the appropriate
umn.
Prog.MIX
• CTL Column
Flap set
Press the button in the appropriate row to as-
sign a control to the respective mixer. Refer to the
V-Tail
BASE submenu CTL Set section (page 90) for in-
formation on setting switches. When the phase
is activated by turning the
Column, the assigned switch will perform the ad-
justments made in the SET display screen.
BACK
PHASE 1 Flap MIX SERVO
FLAP TYPE ACT SET CTL
>>
FLAP
AILE >> FLAP >> ON
INH
>>
ELEV >> FLAP INH ON
>>
FLAP >> ELEV INH ON
(Active)
ON or inhibit INH a specific phase
(Setting)
>> button in the SET col-
(Control/Switch)
ON
button in the ACT
FLAP Line
By pressing the >> button in the FLAP line, one of
three display screens will appear, depending on the
selected number of flaps:
BACK PHASE 1 Flap MIX
FLAP
FLAP1
RATE A +100%
RATE B +100%
OFFSET 000%
BACK
PHASE 1 Flap MIX
FLAP
FLAP1 FLAP2
RATE A +100% +100%
RATE B +100% +100%
OFFSET 000% 000%
BACK PHASE 1 Flap MIX
FLAP
FLAP1 FLAP3 FLAP4 FLAP2
+100% +100% +100% +100%
RATE A
RATE B +100% +100% +100% +100%
OFFSET 000% 000% 000% 000%
• Lines RATE A / B
Determine the value input in the RATE A / B line the
flap deflection grade through the selected control
when the following situations occur:
SERVO
INC
RES
DEC
SERVO
INC
RES
DEC
SERVO
INC
RES
DEC