GRAUPNER mz-24 Pro Programming Manual page 146

Following the standard conventions for model types
Airplane, Glider and Helicopter when assigning con-
trol functions.
Channel Function
1 Motor/airbrake or pitch
2 Aileron or Roll
3 Elevator or Nick
4 Rudder or Yaw
Select by pressing the control function inputs 1 to 12
to be transferred to the PUPIL. In the example below,
inputs 1 - 4 have been transferred to the pupil:
BACK Trainer
CH 1. PUPIL CH 7. TEACH CTL
CH 2. CH 8. TEACH NONE
PUPIL
CH 3. PUPIL CH 9. TEACH BIND
CH 4. PUPIL CH 10. TEACH OFF
CH 5. TEACH CH 11. TEACH TYPE
CH 6. TEACH CH 12. TEACH RF
To change between teacher and pupil a trainer-switch
must be assigned in the CTL column value field. Re-
fer to the Control and Switch Assignment section
(page 26).
Using an intermittent switch, such as S8, is highly rec-
ommended so that control can be easily withdrawn
from the trainer at any time:
146 Function menu | general - Trainer
BACK
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
Since the trainer system programming an operable
PUPIL transmitter will not be connected to a TEACH
transmitter, the transmitter will react with acoustical
alarms to switches connected during the switch as-
signment. A warning message flashes every second
at the top left in the transmitter's main display. Open
the switch that has just been assigned.
Binding PUPIL Transmitter to TEACH Transmitter
Notice
During binding, the transmitters cannot be too far
SERVO
apart. If binding fails, bring the two transmitters
closer together, and restart the binding process.
Start the binding process in the PUPIL transmitter by
pressing the value field button in the BIND column:
BACK
CH 1.
CH 2.
CH 3.
CH 4.
CH 5.
CH 6.
Trainer SERVO
PUPIL TEACH
CH 7. CTL
PUPIL CH 8. TEACH SW 8
PUPIL CH 9. TEACH BIND
PUPIL CH 10. TEACH OFF
TEACH CH 11. TEACH TYPE
TEACH CH 12. TEACH RF
Trainer SERVO
TEACH CH 7. TEACH CTL
TEACH CH 8. TEACH NULL
CH 9.
TEACH TEACH BIND
TEACH CH 10. TEACH OFF
TEACH CH 11. TEACH TYPE
Press
TEACH CH 12. TEACH RF
Immediately press the same button on the TEACH
transmitter:
BACK Trainer
CH 1. PUPIL CH 7. TEACH CTL
CH 2. PUPIL CH 8. TEACH SW 8
CH 3. PUPIL CH 9. TEACH BIND
CH 4. PUPIL CH 10. TEACH OFF
CH 5. TEACH CH 11. TEACH TYPE
Press
TEACH CH 12. TEACH RF
CH 6.
The value field shows ON in both displays:
BACK Trainer
CH 1. TEACH CH 7. TEACH
CTL
CH 2. TEACH CH 8. TEACH NULL
CH 3. TEACH CH 9. TEACH BIND
CH 4. TEACH CH 10. TEACH ON
CH 5. TEACH CH 11. TEACH TYPE
CH 6. TEACH CH 12. TEACH RF
BACK
Trainer
CH 1. PUPIL CH 7. TEACH CTL
CH 2. CH 8.
PUPIL TEACH SW 8
CH 3. PUPIL CH 9. TEACH BIND
CH 4. PUPIL CH 10. TEACH ON
CH 5. TEACH CH 11. TEACH
TYP
CH 6. TEACH CH 12. TEACH DSC-S
The transmitters are now bound. Both transmitters
can now return to the basic display and commence
training after a thorough check of all functions.
Bind has failed if only one (or neither) transmitter dis-
plays ON in the BIND column. Bring the two trans-
mitters closer together, and restart the binding pro-
cess.
Attention
BEFORE starting trainer mode for the operational
model, always make sure all functions have been
correctly transferred.
SERVO
SERVO
SERVO