GRAUPNER mz-24 Pro Programming Manual page 116

VOICE TRIGGER
To open the Voice Trigger submenu, press the button
in the VOICE TRIGGER line:
BACK Telemetry
RX SELECT RX1 ALWAYS
>>
SETTING & DATA VIEW
SENSOR >>
Press
>>
RF STATUS VIEW
>>
VOICE TRIGGER
The following display opens:
BACK Telemetry
10s NULL AUTO
REPEAT TONE
TRIGGER NULL VARIO NULL
>> >>
TRANSMITTER RECEIVER
GENERAL MOD >> ELEC MOD >>
>> >>
VARIO MOD GPS MOD
>>
ESC MOD
REPEAT
To start audio reproduction in the REPEAT line a
switch must be assigned. Refer to the Control and
Switch Assignment section (page 26) for information
on how to assign switches. Press the second field in
the REPEAT line to assign or reassign a switch:
BACK Telemetry
REPEAT 10s NULL TONE AUTO
TRIGGER NULL VARIO NULL
Press
TRANSMITTER >> RECEIVER >>
>>
GENERAL MOD >> ELEC MOD
>> >>
VARIO MOD GPS MOD
ESC MOD >>
116 Function menu - Telemetry | Voice Trigger
An active display box appears:
BACK
REPEAT
TRIGGER
TRANSMITTER
INC
GENERAL MOD
RES
VARIO MOD
DEC
ESC MOD
The active switch will play the reproduced message
and repeat it at the time intervals selected in the first
field of the REPEAT line.
TONE
If the transmitter recognizes multiple Vario sensors,
(e.g. both a General Electric and a GPS module are
INC
installed in the model and connected to the receiver),
RES
after pressing the value field in the TONE line, use
DEC
the INC or DEC
nounce options:
BACK
REPEAT
TRIGGER
TRANSMITTER
GENERAL MOD
VARIO MOD
ESC MOD
The following options are available: VARIO, GAM,
EAM, GPS and AUTO. (In the AUTO position the sen-
INC
sors order will be selected as per the aforementioned
RES
list.)
DEC
Tips
• To recall the vario tones, assign a switch in the fol-
lowing VARIO value field.
Telemetry
10s NULL TONE AUTO
Select
NEIN VARIO NULL
NO
>> >> INC
R EIVER
CLR
>> EAMOD >> RES
LOGIC
>> >> DEC
GPS MOD
>>
(Module Select)
buttons to scroll through vario an-
Telemetry
10s NULL TONE AUTO
NULL VARIO NULL
Press
>> >> INC
RECEIVER
>> ELEC MOD >> RES
Press
>> >> DEC
GPS MOD
>>
• As soon as the transmitter and/or the receiver have
been switched on, the system starts to search the
connected sensors. To change the value field in the
TONE line, 30 seconds must pass so the system
can complete the sensor search. If a value other
than ALWAYS has been selected in the RX SE-
LECT line, such as 4x or 8x , then the process will
take longer:
BACK Telemetry
RX SELECT RX1 ALWAYS
SETTINGS & DATA VIEW >>
>>
SENSOR
RF STATUS VIEW >>
>>
VOICE TRIGGER
TRIGGER (NEXT ANNOUNCE)
• Manual
When a switch is assigned to this line, users can
incrementally cycle between the TRANSMITTER
and RECEIVER options (page 117) and the voice
triggers selected under the Sensors display (page
113). It is recommended to chose a self-neutral-
izing switch: S2 or S8. Refer to the Control and
Switch Assignment section (page 26) for informa-
tion on how to assign switches.
BACK Telemetry
REPEAT 10s NULL TONE AUTO
TRIGGER NULL VARIO NULL
TRANSMITTER >> RECEIVER >>
Press
>> >>
GENERAL MOD ELEC MOD
>> >>
VARIO MOD GPS MOD
ESC MOD >>
INC
RES
DEC
INC
RES
DEC